LG Flatron W2486l Owners Manual

www.lg.com
OWNER’S MANUAL
LCD MONITOR 
L\fD MONITOR MODELS
W2286L
W2486L
Plea\fe  read  t\bi\f  manual  carefully  before  operating  your  \fet  and 
retain it for future reference.
ENGLISH
  

1
Important Precautions
This unit has been engineered and manufactured to ensure your personal
safety, however improper use may result in potential electrical  shock or fire
hazards. In order to allow the proper operation of all safeguards
incorporated in this display, observe the following basic rules for its
installation, use, and servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards...

2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place
the display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which may...

Important Precautions
3
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display
screen because over-spraying may cause electrical shock.
When cleaning the product, unplug the power cord and scrub gently with a soft
cloth to prevent scratching. Do not clean with a wet cloth or spray water or
other liquids directly onto the product. An electric shock may occur. (Do not use
chemicals such as benzene,...

4
Accessories
Users Guide/CardsPower Cord
15-pin D-Sub Signal Cable
(To set it up, this signal cable may
be attached to  this product before
shipping out.)DVI-D Signal Cable
(This feature is not available
in all countries.)
NOTEThis accessories may look different from those shown here.
User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferrite
cores to maintain standard compliance for the product.
Cable Holder(This feature is not
available in all models.)AC-DC adapter...

5
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor,
the computer system, and other attached devices is turned off. 
Connecting and Disassembling the stand
1.Place the monitor face down on the soft cloth.
2.Assemble the Stand Base into the Stand Body in the correct direction.
Make sure you push the Stand Base until the end.
Stand Base Stand Body
The Stand Base may
fall and get damaged
or cause injury.
Good ConnectionBad Connection
 

6
Connecting the Display
IMPORTANT
This picture depicts the general model of connection. Your monitor may differ from the items
shown in the picture.
Do not carry the product upside down holding only the stand base. The product may fall and
get damaged or cause injury.
4.Then fold the screw handle flat. 5.Once assembled take the monitor up
carefully and face the front side.
6.To disconnect the Stand Base from the Stand Body, unfold the screw handle and
turn it to the left. 
3.Turn the screw to the right...

7
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor,
the computer system, and other attached devices is turned off. 
Positioning your display
After installation, adjust the angle as shown below. 
1.Adjust the position of the panel in various ways for maximum comfort.
Tilt Range : -2˚ to 15˚                            
ERGONOMIC
It is recommended that in order to maintain an ergonomic and comfortable viewing position,
the forward tilt angle of the monitor should...

8
Connecting the Display
A
B
Connect DVI-D(Digital signal) Cable
Connect D-sub(Analog signal) Cable 
Connect HDMI Cable 
1.Before setting up the monitor, ensure that the power to the monitor, the computer system, and
other attached devices is turned off.  
2.Connect the signal cable        . When attached, tighten the thumbscrews to secure the 
connection.
3.Connect the power cable        with the AC-DC adapter (AC-DC power supply)       , and then
plug the cable in the outlet.
Connecting with the PC/AV...

9
Connecting the Display
NOTE
‘ Self Image Setting Function’? This function provides the user with optimal display
settings.When the user connects the monitor for the first time, this function automatically adjusts
the display to optimal settings for individual input signals. 
‘AUTO/SET’ Function? When you encounter problems such as blurry screen, blurred letters,
screen flicker or tilted screen while using the device or after changing screen resolution, press
the AUTO/SETfunction button to improve...