LG Flatron W2452v Users Guide

Make sure to read the Important Precautionsbefore using the product. 
Keep the Users Guide(CD) in an accessible place for future reference.
See the label attached on the product and give the information to your
dealer when you ask for service.
W2452V
User’s Guide
 

A1
This unit has been engineered and manufactured to ensure your personal
safety, however improper use may result in potential electrical  shock or fire
hazards. In order to allow the proper operation of all safeguards
incorporated in this display, observe the following basic rules for its
installation, use, and servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided...

A2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place the
display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release of
heat generated during operation. If these openings are blocked, built-up heat can
cause failures which...

Stand Body Stand Base
Stand Base
A3
Connecting the Display
Important
This illustration depicts the general model of connection. Your monitor may differ from
the items shown in the picture.
Do not carry the product upside down holding only the stand base. The product may
fall and get damaged or injure your foot.
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Connecting the stand 
1.Place the monitor with its front facing...

A4
Connecting the Display
Disassembling the stand
1.Put a cushion or soft cloth on a flat surface.
2.Place the monitor face down on the cushion or soft cloth.
4.Loosen the screw, then take off the stand base from stand body.
5.Please pull the stand body lightly to separate it from the hinge body. 
3.Slide the Cable Deco Cover out from the stand body.
Important
Your monitor may differ from the items shown in the picture.
 

A5
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off. 
Positioning your display
1.Adjust the position of the panel in various ways for maximum comfort.
Tilt Range:-5˚~20˚ 
Ergonomic
It is recommended that in order to maintain an ergonomic and comfortable viewing
position, the forward tilt angle of the monitor should not exceed 5 degrees.
Swivel:355˚ 
 

A6
Using the Computer
1.Make sure to turn off the computer and  product. Connect the cable as below sketch map
form to .1
3.Press        button on the front switch panel to turn the power on.
When monitor power is turned on, the Self Image Setting
Functionis executed automatically.
(Only RGB Mode)
NOTE‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user connects the
monitor for the first time, this function automatically adjusts the display to...

A7
Connecting the Display
4.Press the SOURCEbutton at the front side of the monitor.
When connecting with a DVI signal input cable.
• Select DVI: DVI digital signal.
When connecting with a D-sub signal cable.
• Select RGB: D-sub analogue signal.
When connecting with a HDMI cable.
• Select HDMI
RGB
DVI INPUT
HDMI
 

A8
Control Function
Control Panel Functions
MENU ButtonUse this button to enter or exit from the On Screen Display.
FUN ButtonUse this button to enter EZ ZOOMING, 4:3 IN WIDE,
PHOTO EFFECT, SOUND items, for more information,
refer to page A17-A18.
Use this button to enter On Screen Display Sub-menu
to adjust BRIGHTNESS directly.
OSD LOCKED/UNLOCKED
This function allows you to lock the current control settings, so
that these settings are not inadvertently changed. To lock the
OSD settings, press and hold...

A9
Control Panel Functions
This Indicator lights up as blue when the display is
operating normally(On Mode). If the display is in
Sleep Mode (Energy Saving), this indicator color
changes to amber. Use this button to turn the display on or off.
Power Button
Power Indicator
Use this button to select an icon in the On Screen
Display.AUTO/SET
Button
AUTO IMAGE ADJUSTMENT
When adjusting your display settings, always press
the AUTO/SETbutton prior to entering the On
Screen Display(OSD). This will automatically...