LG Flatron W2246pm Users Guide

							20
On Screen Display(OSD) Selection and Adjustment 
Main menu Sub menu Description
Change the input image signal ratio to
original. 
WIDE
ORIGINALSwitch to full screen mode according to
input image signal.  
* This function works only if input
resolution is lower than monitor ratio
(16:9).
Exit: Exit,     : Move: Select another sub-menu
 
						

							21
Troubleshooting
No image appears
Check the following before calling for service.
No image appears
Do you see a OSD LOCKED message on the screen?
Is the power cord of the
display connected?
Is the power indicator
light on?
Is the power indicator
flickering?
Do you see an OUT OF
RANGE message on
the screen?
Do you see a CHECK
SIGNAL CABLE
message on the
screen?• Check and see if the power cord is connected
properly to the power outlet.
• Press the Power button.
• If the display is in power saving mode, try moving
the mouse or pressing any key on the keyboard to
bring up the screen.
• Try to turn on the PC.
• This message appears when the signal from the
PC (video card) is out of horizontal or vertical
frequency range of the display. See the
Specifications section of this manual and
configure your display again.
• This message appears when the signal cable
between your PC and your display is not
connected. Check the signal cable and try again.
• You can secure the current control settings,
so that they cannot be inadvertently changed.
You can unlock the OSD controls at any time
by pushing the MENUbutton for several
seconds: the message 
“OSD UNLOCKED”will appear. Do you see “OSD
LOCKED” when you
push MENU button?
 
						

							22
Troubleshooting
Display image is incorrect
Display Position is
incorrect.
On the screen
background, vertical
bars or stripes are
visible.
Any horizontal noise
appearing in any
image or characters
are not clearly
portrayed.• Press the AUTObutton to automatically adjust
your display image to the ideal setting. 
If the results are unsatisfactory, adjust the image
position using the H position and V positionicon
in the on screen display.
• Press the AUTObutton to automatically adjust
your display image to the ideal setting.
If the results are unsatisfactory, decrease the
vertical bars or stripes using the CLOCKicon in
the on screen display.
• Press the AUTObutton to automatically adjust
your display image to the ideal setting.
If the results are unsatisfactory, decrease the 
horizontal bars using the PHASEicon in the on 
screen display.
• Check Control Panel --> Display --> Settings
and adjust the display to the recommended
resolution or adjust the display image to the ideal
setting. Set the color setting higher than 24 bits
(true color).
IMPORTANT
Check Control Panel --> Display --> Settingsand see if the frequency or the
resolution were changed. If yes, readjust the video card to the recommend
resolution.
If the recommended resolution (optimal resolution) is not selected, letters may be
blurred and the screen may be dimmed, truncated or biased. Make sure to select
the recommend resolution. 
The setting method can differ by computer and O/S (Operation System), 
and resolution mentioned above may not be supported by the video card    
performance. In this case, please ask to the computer or the video card  
manufacturer. 
 
						

							23
Display image is incorrect
Troubleshooting
The screen color is
mono or abnormal.
The screen blinks.• Check if the signal cable is properly connected
and use a screwdriver to fasten if necessary.
• Make sure the video card is properly inserted in
the slot.
• Set the color setting higher than 24 bits (true color)
at Control Panel - Settings.
• Check if the screen is set to interlace mode and if
yes, change it to the recommend resolution.
Do you see an Unrecognized monitor, Plug&Play (VESA
DDC) monitor found message?
Have you installed the
display driver?• Be sure to install the display driver from the display
driver CD (or diskette) that comes with your
display. Or, you can also download the driver from
our web site: http://www.lge.com.
• Make sure to check if the video card supports
Plug&Play function.
 
						

							24
Specifications                                                                 W1946PM
47.0 cm (18.5 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating 
Visible diagonal size : 47.0cm
0.300 x 0.300 mm (Pixel pitch)
Display
Horizontal Freq. 30 kHz to 61 kHz (Automatic)
Vertical Freq. 56 Hz to 75 Hz (Automatic)
Input Form Separate Sync.
SOG (Sync On Green), DigitalSync Input
Signal Input 15 pin D-Sub Connector
DVI-D Connector (Digital)
Input Form RGB Analog (0.7 Vp-p/ 75 ohm), DigitalVideo Input
Max VESA 1360 x 768 @60 Hz
Recommend VESA 1360 x 768 @60 HzResolution
Plug&Play
On Mode:24 W(Typ.)
Sleep Mode≤0.5 W
Off Mode≤0.5 WPower
Consumption
Operating Conditions
Temperature 10 ˚C to 35 ˚C
Humidity 10 % to 80 % non-Condensing
Storage Conditions
Temperature -20 ˚C to 60 ˚C
Humidity 5 % to 90 % non-CondensingEnvironment
al Conditions
With Stand
Width    44.26 cm ( 17.42 inch) 
Height 35.62 cm ( 14.02 inch)
(Min.)
46.62 cm (18.35 inch) (Max.)
Depth 16.99 cm (   6.68 inch)
Weight(excl. packing) 3.9 kg (8.66 lb)
Dimensions
& Weight
Tilt -4˚ to 17˚
Swivel                356˚
Height              110 mm / 4.33 inchRange
AC 100 - 240 V~  50 / 60 Hz 0.8 A Power Input
Attached (     ), Detached ( O )Stand Base 
Wall-outlet typePower cord 
DDC 2B(Digital),DDC2AB(Anlaog)
Without Stand
Width    44.26 cm ( 17.42 inch) 
Height 26.67 cm (10.50 inch)   
Depth 6.04 cm (   2.37 inch)
NOTE
Information in this document is subject to change without notice.
 
						

							25
Specifications                                                                 W2246PM
54.6 cm (21.5 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating 
Visible diagonal size : 54.6cm
0.248 x 0.248 mm (Pixel pitch)
Display
Horizontal Freq. 30 kHz to 83 kHz (Automatic)
Vertical Freq. 56 Hz to 75 Hz (Automatic)
Input Form Separate Sync.
SOG (Sync On Green), DigitalSync Input
Signal Input 15 pin D-Sub Connector
DVI-D Connector (Digital)
Input Form RGB Analog (0.7 Vp-p/ 75 ohm), DigitalVideo Input
Max VESA 1920 x 1080 @60 Hz
Recommend VESA 1920 x 1080 @60 HzResolution
Plug&Play
On Mode:26 W(Typ.)Sleep Mode≤0.5 W
Off Mode≤0.5 WPower
Consumption
Operating Conditions
Temperature 10 ˚C to 35 ˚C
Humidity 10 % to 80 % non-Condensing
Storage Conditions
Temperature -20 ˚C to 60 ˚C
Humidity 5 % to 90 % non-CondensingEnvironment
al Conditions
With Stand
Width    50.92 cm ( 20.04 inch) 
Height 39.69 cm ( 15.62 inch) 
(Min.)
50.69 cm ( 19.95 inch) (Max.)
Depth 21.00 cm (   8.26 inch)
Weight(excl. packing) 4.4 kg (9.77 lb)
Dimensions
& Weight
Tilt -4˚ to 17˚
Swivel                356˚
Height              110 mm / 4.33 inchRange
AC 100 - 240 V~  50 / 60 Hz 1.0 A Power Input
Attached (     ), Detached ( O )Stand Base 
Wall-outlet typePower cord 
DDC 2B(Digital),DDC2AB(Anlaog)
Without Stand
Width    50.92 cm ( 20.04 inch) 
Height 30.42 cm ( 11.97 inch)
Depth 5.98 cm (   2.35 inch)
NOTE
Information in this document is subject to change without notice.
 
						

							26
Specifications                                                                 W2346PM
58.4 cm (23 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating 
Visible diagonal size : 58.4cm
0.266 x 0.266 mm (Pixel pitch)
Display
Horizontal Freq. 30 kHz to 83 kHz (Automatic)
Vertical Freq. 56 Hz to 75 Hz (Automatic)
Input Form Separate Sync.
SOG (Sync On Green), DigitalSync Input
Signal Input 15 pin D-Sub Connector
DVI-D Connector (Digital)
Input Form RGB Analog (0.7 Vp-p/ 75 ohm), DigitalVideo Input
Max VESA 1920 x 1080 @60 Hz
Recommend VESA 1920 x 1080 @60 HzResolution
Plug&Play
On Mode:29 W(Typ.)
Sleep Mode≤0.5 W
Off Mode≤0.5 WPower
Consumption
Operating Conditions
Temperature 10 ˚C to 35 ˚C
Humidity 10 % to 80 % non-Condensing
Storage Conditions
Temperature -20 ˚C to 60 ˚C
Humidity 5 % to 90 % non-CondensingEnvironment
al Conditions
With Stand
Width    54.25 cm ( 21.35 inch) 
Height 41.66 cm ( 16.40 inch) 
(Min.)
52.66 cm ( 20.73 inch) (Max.)
Depth 21.00 cm (   8.26 inch)
Weight(excl. packing) 5.1 kg (11.33 lb)
Dimensions
& Weight
Tilt -4˚ to 17˚
Swivel                356˚
Height              110 mm / 4.33 inchRange
AC 100 - 240 V~  50 / 60 Hz 1.0 A Power Input
Attached (     ), Detached ( O )Stand Base 
Wall-outlet typePower cord 
DDC 2B(Digital),DDC2AB(Anlaog)
Without Stand
Width    54.25 cm ( 21.35 inch) 
Height 32.30 cm ( 12.71 inch)
Depth 6.05 cm  (  2.38 inch)
NOTE
Information in this document is subject to change without notice.
 
						

							27
Indicator
On Mode
Sleep Mode
Off ModeWhite
White Blinking
Off
LED Color
MODE
Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)
*Recommend Mode
W2246PM/W2346PM
1
2
3
4
5
6
7
8
9
10
11
*12720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
1024 x 768
1024 x 768
1152 x 864
1280 x 1024
1280 x 1024
1680 x 1050
1920 x 108031.468
31.469
37.500
37.879
46.875
48.363
60.123
67.500
63.981
79.976
65.290
67.50070
60
75
60
75
60
75
75
60
75
60
60
Specifications
Preset Modes (Resolution)
Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)
*Recommend Mode
W1946PM
1
2
3
4
5
6
7
8
*9720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1360 x  76831.468
31.469
37.500
37.879
46.875
49.725
48.363
60.123
47.71270
60
75
60
75
75
60
75
60
 
						

							28
Installing the Wall mount plate
Mounting crew:
Interface pad thickness: 2.6 mm
Screw : 
4 mm x pitch 0.7 mm x length 10 mm
This monitor satisfies the specifications of the  Wall mount plate or
the interchange device.
Wall mount plate (Separate purchase)- Be sure to use screws and a wall mount that meet VESA
standards.
- Using screws longer than those recommended might
damage the product.
- Using screws that do not meet VESA standards might
either damage the product or result in it coming away
from the wall.We will not be held responsible for any
damage resulting from failure to follow these instructions.
Kensington Security SlotConnected to a locking  cable that
can be purchased separately at
most computer stores.
1. After moving the product to face
downward, make sure to place it on a
soft cloth or a cushion to avoid surface
damage.  
2. Separate the head and the stand with
the use of a screwdriver.
3. Install the Wall mount plate.
 
						

							Digitally yours