LG Flatron W2243c Owners Manual

www.lg.com
OWNER’S MANUAL
LCD MONITOR 
L\fD MONITOR MODELS
W1943SS   W1943TS
W2043SE  W2043TE
W2243SE  W2243TE
\flea\be  read  thi\b  manual  carefully  before  operating  your  \bet  and 
retain it for future reference.
ENGLISH
  

1
This unit has been engineered and manufactured to ensure your personal safety,
however improper use may result in potential electrical  shock or fire hazards. In
order to allow the proper operation of all safeguards incorporated in this display,
observe the following basic rules for its installation, use, and servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided...

2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place
the display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which may...

Important Precautions
3
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display
screen because over-spraying may cause electrical shock.
When cleaning the product, unplug the power cord and scrub gently with a soft
cloth to prevent scratching. Do not clean with a wet cloth or spray water or
other liquids directly onto the product. An electric shock may occur. (Do not use
chemicals such as benzene,...

4
Accessories
!!! Thank for selecting LGE products !!! 
Please make sure the following items are included with your
monitor. If any items are missing, contact your dealer.
IMPORTANTThis accessories may look different from those shown here.
User must use shielded signal interface cables (D-sub 15 pin cable, DVI cable) with ferrite
cores to maintain standard compliance for the product.
Users Guide/CardsPower Cord(Depending on the  country)
15-pin D-Sub Signal Cable
(To set it up, this signal cable may
be...

5
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor,
the computer system, and other attached devices are turned off. 
Connecting and Disassembling the stand
1.Place the monitor face down on the soft cloth.
2.Assemble the Stand Base into the Stand Body in the correct direction.
Stand Base Stand Body
3.Turn the Stand Base Lock through 90˚ to fix the Stand Base to the Stand Body. 
4.Once assembled, lift the monitor up carefully.
Base Lock
 
 

6
Connecting the Display
IMPORTANTThis picture depicts the general model of connection. Your monitor may differ from the items
shown in the picture.
Do not carry the product upside down holding only the stand base. The product may fall and
get damaged or cause injury.
5.Turn the Stand Base Lock through 90˚ to separate the Stand Base from the Stand
Body. 
 
6.Pull out the Stand Base to remove. 
If you cant release the Stand Base even the Locking Knob is at a release position,
Please push the indicated...

7
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor,
the computer system, and other attached devices is turned off. 
Positioning your display
-After installation, adjust the angle as shown below. 
1.Adjust the position of the panel in various ways for maximum comfort.
Tilt Range : -5˚~15˚                            
ERGONOMIC
It is recommended that in order to maintain an ergonomic and comfortable viewing position,
the forward tilt angle of the monitor should not...

8
Connecting the DisplayW1943TS/W2043TE/W2243TE
NOTE‘ Self Image Setting Function’? This function provides the user with optimal display
settings.When the user connects the monitor for the first time, this function automatically adjusts
the display to optimal settings for individual input signals. 
‘AUTO/SET’ Function? When you encounter problems such as blurry screen, blurred letters,
screen flicker or tilted screen while using the device or after changing screen resolution, press
the AUTO/SET function...

9
Connecting the DisplayW1943SS/W2043SE/W2243SE
NOTE‘ Self Image Setting Function’? This function provides the user with optimal display
settings.When the user connects the monitor for the first time, this function automatically adjusts
the display to optimal settings for individual input signals. 
‘AUTO/SET’ Function? When you encounter problems such as blurry screen, blurred letters,
screen flicker or tilted screen while using the device or after changing screen resolution, press
the AUTO/SET function...