LG Flatron W1934s Users Guide

Make sure to read the Important Precautionsbefore using the product. 
Keep the Users Guide(CD) in an accessible place for future reference.
See the label attached on the product and give the information to your
dealer when you ask for service.
W1934S
W2234S
W1934SE
W2234SE
User’s Guide
 

A1
This unit has been engineered and manufactured to ensure your personal safety,
however improper use may result in potential electrical  shock or fire hazards. In
order to allow the proper operation of all safeguards incorporated in this display,
observe the following basic rules for its installation, use, and servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided...

A2
Important Precautions
Do not use this display near water such as near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a...

A3
Connecting the Display
Important
This illustration depicts the general model of connection. Your monitor may differ from
the items shown in the picture.
Do not carry the product upside down holding only the stand base. The product may
fall and get damaged or injure your foot.
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Connecting the stand 
1.Place the monitor with its front facing downward on a soft cloth.
2.Check...

A4
Connecting the Display
Disassembling the stand
1.Put a cushion or soft cloth on aflat
surface.2.Place the monitor face Down on
the cushion or soft cloth.
3.Hold the Head Part with one hand and
hold the Stand Base Part with the other
as shown in the picture and pull the
Stand Base Part lightly upward  
5.Please pull the stand body lightly to separate it from the hinge body. 
Stand Base
PartHead Part
4.Pushing Latch inside, Take the
stand base from stand body.
 

A5
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off. 
Positioning your display
1.Adjust the position of the panel in various ways for maximum comfort.
Tilt Range : -5˚~20˚                            
Ergonomic
It is recommended that in order to maintain an ergonomic and comfortable viewing
position, the forward tilt angle of the monitor should not exceed 5 degrees.
 

A6
Using the Computer
1.Make sure to turn off the computer and  product.
Connect Signal cable      and Power cord      in order, then tighten the screw of the
signal cable. 1
2.Press        button on the front switch panel to turn the
power on. When monitor power is turned on, the Self
Image Setting Function is executed automatically.
2
Connecting the Display
A
B
Connect Dsub Cable (PC)
Connect Dsub Cable (Mac)
NOTEThis is a simplified representation of the rear view.
This rear view represents a general...

A7
Control Panel Functions
4 : 3 in Wide
Button
MENU ButtonUse this button to enter or exit the On Screen Display.
OSD LOCKED/UNLOCKED
This function allows you to lock the current control
settings, so that they cannot be inadvertently changed.
Press and hold the MENU buttonfor several seconds.
The message OSD LOCKEDshould appear.
You can unlock the OSD controls at any time by pushing
the MENU buttonfor several seconds. The message
OSD UNLOCKEDshould appear.
Front Panel Controls
5
6
WIDE mode 4 : 3...

A8
Control Panel Functions
This Indicator lights up blue when the display operates
normally(On Mode). If the display is in Sleep Mode
(Energy Saving), this indicator color changes 
to amber. Use this button to turn the display on or off.
Power Button
Power Indicator
Use this button to enter a selection in the On Screen 
Display.AUTO/SET
Button
AUTO IMAGE ADJUSTMENT
When adjusting your display settings, always press
the AUTO/SETbutton before entering the On Screen
Display(OSD). This will automatically...

A9
On Screen Display (OSD) Control Adjustment
Screen Adjustment
Making adjustments to the image size, position and operating parameters of
the display is quick and easy with the On Screen Display Control system. 
A short example is given below to familiarize you with the use of the controls.
The following section is an outline of the available adjustments and selections
you can make using the OSD.
To make adjustments in the On Screen Display, follow these steps:
Press the MENU Button, then the main menu...