LG Flatron N1941wp Users Guide

N1642W
N1642WP
N1941W
N1941WP
N1941WE
User’s Guide
Network Monitor
Make sure to read the Important Precautionsbefore using the product. 
Keep the Users Guide(CD) in an accessible place for future reference.
See the label attached on the product and give the information to your
dealer when you ask for service.
With LG Network Monitor, some PC programs may not be compatible or
need to be modified due to different kind of operation.
Please check the compatibility in advance, before purchasing or installing...

Accessories
!!! Thank for selecting LGE products !!! 
Please make sure the following items are included with your
monitor. If any items are missing, contact your dealer.
Users Guide/Cards
Power Cord(Depending on the  country)
15-pin D-Sub Signal Cable
(To set it up, this signal cable may
be attached to  this product before
shipping out.)
IMPORTANTThis accessories may look different from those shown here.User must use shielded signal interface cables (D-sub 15 pin cable, LAN cable) with ferrite
cores to...

A1
This unit has been engineered and manufactured to ensure your personal
safety, however improper use may result in potential electrical  shock or fire
hazards. In order to allow the proper operation of all safeguards
incorporated in this display, observe the following basic rules for its
installation, use, and servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided...

A2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place the
display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which...

A3
Important Precautions
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display
screen because over-spraying may cause electrical shock.
When cleaning the product, unplug the power cord and scrub gently with a soft
cloth to prevent scratching. Do not clean with a wet cloth or spray water or other
liquids directly onto the product. An electric shock may occur. (Do not use
chemicals such as benzene,...

A4
Connecting the Display
Important
This illustration depicts the general model of connection. Your monitor may differ from
the items shown in the picture.
Do not carry the product upside down holding only the stand base. The product may
fall and get damaged or injure your foot.
Before setting up the monitor, ensure that the power to the monitor, the
computer system, and other attached devices is turned off.
Connecting the stand 
1.Place the monitor with its front facing downward on a soft cloth....

A5
Connecting the Display
Disassembling the stand
1.Put a cushion or soft cloth on a flat
surface.
3.Change your lock on the product as it follows and turn it in the arrow direction.
2.Place the monitor face down on the
cushion or soft cloth.
If you cant release the stand base even the locking knob is at a release
position, Please push the indicated knob down and retry it.
4.Pull out the stand to remove.
 

A6
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the
computer system, and other attached devices is turned off. 
Positioning your display
1.Adjust the position of the panel in various ways for maximum comfort.
Tilt Range : -5˚~20˚                            
Ergonomic
It is recommended that in order to maintain an ergonomic and comfortable viewing
position, the forward tilt angle of the monitor should not exceed 5 degrees.
5.Pushing the PUSH button, take the...

A7
Using the Computer
2.Press        button on the front switch panel to turn the 
power on. When monitor power is turned on, the 
Self Image Setting Functionis executed automatically.
Connecting the Display
Wall-outlet type
Analog signal
A
B
Connect D-sub(RGB Analog) Cable (PC)
Connect D-sub(RGB Analog) Cable (Mac)
Mac adapter (This item must be purchased separately.)For Apple Macintosh use, a  separate plug adapter is
needed to change the 15 pin high density (3 row) D-sub
VGA connector on the supplied...

A8
Wall-outlet type
Analog signal
(Make sure to connect X550
port,not LAN port of PC)
Up to 5 ports are supported per X550 PCI Card. 
Up to 5 ports can be connected if necessary.
(These items are not included for all models.)
Using the Monitor
1.Make sure to turn off the computer and  product. Connect the cable as below sketch map
form        to       .12
1
2
Connect peripheral devices
Connect LAN Cable (X550 port)
Connecting the Display
Keyboard/Mouse Input 
LAN cable should be 
connected before boo-...