LG Flatron M2762d Owners Manual

							10
PREPARATION
LOCATION
Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to expose
the set to any unnecessary vibration, moisture, dust or heat. Also, ensure that the set is placed in a position to allow a
free flow of air. Do not cover the ventilation openings on the back cover.
If you intend to mount the set to a wall, attach the wall mounting interface (optional parts) to the back of the set.
When you install the set using the wall mounting interface (optional parts), attach it carefully so it will not drop.
- Be sure to use screws and a wall mount that meet VESA standards.
- Using screws longer than those recommended might damage the product. 
- Using screws that do not meet VESA standards might either damage the product or result in it coming away from the
wall. We will not be held responsible for any damage resulting from failure to follow these instructions.
< Screw Mounting Interface Dimension >
M M2
22
26
62
2D
D/
/M
M2
23
36
62
2D
D/
/M
M2
22
26
62
2D
DP
P/
/M
M2
23
36
62
2D
DP
P
: 100 mm x 100 mm hole spacing
M M2
27
76
62
2D
D/
/M
M2
27
76
62
2D
DP
P 
 
: 200 mm x 100 mm hole spacing
* Wall mount interface(LG) : RW120 
RW240 
W Wa
ar
rn
ni
in
ng
g:
:
When  adjusting  the  angle  of  the
screen,  do  not  put  your  finger(s)in
between the head of the monitor and
the  stand  body.  You  can  hurt  your
finger(s).RW120
RW240
/ownloadedlfroml“anual“onitorOcoml“anuals 
						

							11
PREPARATION
SECURING THE SET TO THE WALL TO PREVENT FALLING
WHEN THE SET IS USED ON A STAND
(Only M2762D/M2762DP)
We recommend that you set up the set close to a wall so it cannot fall over if pushed backwards. 
Additionally, we recommend that the set be attached to a wall so it cannot be pulled in a forward direction,
potentially causing injury or damaging the product. 
Caution: Please make sure that children don’t climb on or hang from the set. 
Insert the eye-bolts (or set brackets and bolts) to tighten the product to the wall as shown in the picture. 
* If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts. 
* Insert the eye-bolts or set brackets/bolts and tighten them securely in the upper holes.
Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that is
mounted on the wall to the holes in the product. 
Ensure the eye-bolts or brackets are tightened securely.
Use  a  sturdy  rope  or  cord  (sold  separately)  to  tie  the  product.  It  is  safer  to
tie the rope so it becomes horizontal between the wall and the product.
Image shown may differ from your set.
GWhen moving the set, undo the cords first.
GUse a platform or cabinet strong enough and large enough to support the size and weight of the set.
GTo use the set safely make sure that the height of the bracket on the wall and the one on the set are the same.
NOTE!
Downloaded@from@ManualMonitorDcom@Manuals 
						

							12
PREPARATION
ATTACHING THE TV TO A DESK (Only M2762D/M2762DP)
The TV must be attached to desk so it cannot be pulled in a forward/backward direction,potentially causing
injury or damaging the product.Use only an attached screw.
The image shown may be somewhat different from your set.
Desk
Stand
WARNING!
GTo  prevent  TV  from  falling  over,the  TV  should  be  securely  attached  to  the  floor/wall  per  installation
instructions. Tipping,shaking, or rocking the machine may cause injury.1-Screw
(provided as parts of the product)
/ownloadedlfroml“anual“onitorOcoml“anuals 
						

							13
PREPARATION
KENSINGTON SECURITY SYSTEM
- The product is equipped with a Kensington Security System connector on the back panel. Connect the
Kensington Security System cable as shown below.
- For detailed installation and use of the Kensington Security System, refer to the user’s guide provided with the
Kensington Security System.
For further information, contact h ht
tt
tp
p:
:/
//
/w
ww
ww
w.
.k
ke
en
ns
si
in
ng
gt
to
on
n.
.c
co
om
m
, the internet homepage of the Kensington
company. Kensington sells security systems for expensive electronic equipment such as notebook PCs and
LCD projectors.
NOTE
- The Kensington Security System is an optional accessory available at most electronics stores.
NOTES
a. If the product feels cold to the touch, there may be a small “flicker” when it is turned on.
This is normal, there is nothing wrong with product.
b. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However,
they have no adverse effect on the monitor's performance.
c. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time.
/ownloadedlfroml“anual“onitorOcoml“anuals 
						

							AV 1 AV 2
AC IN 
14
AV 1 AV 2
AC IN 
ANTENNA/
CABLE IN
AV 1 AV 2
AC IN 
ANTENNA/
CABLE IN
EXTERNAL EQUIPMENT SETUP
For optimum picture quality, adjust antenna direction.
An antenna cable and converter are not supplied.
To prevent equipment damage, never plug in any power cords until you have finished connecting all equipment.
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Outdoor
Antenna
(VHF, UHF)
Wa ll
Antenna
Socket
RF Coaxial Wire (75     )
ANTENNA CONNECTION
Antenna
UHF
VHF
In poor signal areas, to get better picture quality, install a signal amplifier to the antenna as shown above.
If signal needs to be split for two TVs, use an antenna signal splitter for connection.
Signal
Amplifier
/ownloadedlfroml“anual“onitorOcoml“anuals 
						

							Connect the SET-TOP outputs to the C CO
OM
MP
PO
ON
NE
EN
NT
T 
 I
IN
N 
 V
VI
ID
DE
EO
O
sockets (Y PBPR) on the set.
Connect the audio cable from the SET-TOP to C CO
OM
MP
PO
ON
NE
EN
NT
T 
 I
IN
NA
AU
UD
DI
IO
O
sockets of the set.
Press the I IN
NP
PU
UT
T
button to select C Co
om
mp
po
on
ne
en
nt
t.
.
15
EXTERNAL EQUIPMENT SETUP
2
3
1
HD RECEIVER SETUP
To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.
The image shown may be somewhat different from your set.
When connecting with a component cable
Signal
480 i
480 p
576 p
720p/1080i
1080pComponent
Ye s
Ye s
No
Ye s
Ye sHDMI
No
Ye s
Ye s
Ye s
Ye s
VIDEO
COMPONENT
IN
AUDIO
Y
PB
PR
L
R
1
2
/ownloadedlfroml“anual“onitorOcoml“anuals 
						

							16
EXTERNAL EQUIPMENT SETUP
When connecting with a HDMI
Connect  the  HDMI  output  of  the  digital  set-top  box  to  the
H HD
DM
MI
I 
 I
IN
N
jack on the set.1
Connect  the  digital  set-top  box  to H HD
DM
MI
I 
 I
IN
N 
 
jack  on
the set.
Connect  the  audio  output  of  the  digital  set-top  box  to
the A AU
UD
DI
IO
O 
 I
IN
N 
 (
(R
RG
GB
B/
/D
DV
VI
I)
) 
 
jack on the set.
Turn on the digital set-top box. (
Refer to the owner’s
manual for the digital set-top box.)
2
3
1
When connecting with a HDMI to DVI cable
HDMI IN1
2
1
DVI OUTPUTAUDIO
R
L
A
U
D
IO
 IN
(R
G
B
/D
V
I)HDMI IN1
2
12
NOTE!
GHDMI Input does not support PC mode. If it is connected PC, the screen may not display properly.
/ownloadedlfroml“anual“onitorOcoml“anuals 
						

							17
EXTERNAL EQUIPMENT SETUP
DVD SETUP
When connecting with a component cable
Component Input ports
To get better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the set
YPBPR
Video output ports 
on DVD player
Y
Y
Y
YPB
B-Y
Cb
PbP
R
R-Y
Cr
Pr
Connect the video output sockets (Y PBPR) of the DVD to the C CO
OM
MP
PO
ON
NE
EN
NT
T 
 I
IN
N 
 V
VI
ID
DE
EO
O
sockets (Y P
BPR) of the set.
Connect the audio cable from the DVD to C CO
OM
MP
PO
ON
NE
EN
NT
T 
 I
IN
N 
 A
AU
UD
DI
IO
O 
 
sockets of the set.
Press the I IN
NP
PU
UT
T
button to select 
C Co
om
mp
po
on
ne
en
nt
t.
Press the P PL
LA
AY
Y
button on the DVD.
The DVD playback picture appears on the screen.
2
3
4
1
VIDEO
COMPONENT
IN
AUDIO
Y
PB
PR
L
R
1
2
/ownloadedlfroml“anual“onitorOcoml“anuals 
						

							18
EXTERNAL EQUIPMENT SETUP
When connecting HDMI cable
Connect the HDMI output of the DVD to the H HD
DM
MI
I 
 I
IN
N
jack on the set.1
GHDMI supports video and audio. You do not need to connect a sperate audio cable.
GIf the DVD player does not support Auto HDMI, you need to set the DVD output resolution appropriately.
NOTE!
HDMI IN1
2
1
When connecting S-Video
Connect the S-Video output of the DVD to the S-Video in put on the set.
Connect the audio output of the DVD to the AUDIO in put on the set.1
2
VIDEO AUDIO
(MONO)
S-VIDEO
L
R
AV-IN
VIDEO
S-VIDEO
L
R
1
2
/ownloadedlfroml“anual“onitorOcoml“anuals 
						

							19
EXTERNAL EQUIPMENT SETUP
VCR SETUP
To avoid picture noise (interference), leave an adequate distance between the VCR and the set.
If a user uses 4:3 picture format for a long time, an afterimage may remain on the sides of the screen for a
short time.
OUTPUT
SWITCH ANT IN
RS-VIDEO VIDEO
ANT OUTLANTENNA/
CABLE IN
AV 1 AV 2
Wall Jack
Antenna
1
2
When connecting with an antenna
Connect the RF out socket of the VCR to the antenna socket of the set.
Connect the antenna cable to the RF aerial in socket of the VCR.
Store the VCR channel on a desired channel number using the ‘Manual channel tuning’ section.
Select the Channel number where the VCR channel is stored.
Press theP PL
LA
AY
Y 
 
button on the VCR.1
2
3
4
5
/ownloadedlfroml“anual“onitorOcoml“anuals