LG Flatron M2280d Owners Manual

							121
APPENDIX
01. Power (Command: k a)
  To cont\bo\f Powe\b On/Off of the TV.
 Transmission [k][a][  ][Set I\f][  ][\fata][Cr]
 Data 00: Powe\b Off  Data 01: Powe\b On
 Acknowledgement [a][  ][Set I\f][  ][OK/NG][\fata][x]
 *  
In  a  \fike  manne\b,  if  othe\b  functions  t\bansmit  ‘FF’  data 
based  on  this  fo\bmat,  Acknow\fedgement  data  feed-
back p\besents status about each function.
  *  
Note: In this mode\f, TV wi\f\f send the Acknow\fedge afte\b 
powe\b on p\bocessing comp\fetion.
    
The\be  might  be  a  time  de\fay  between  command  and 
acknow\fedge.
02. Input Select (Command: x b)
        To se\fect input sou\bce fo\b TV. 
 Transmission [x][b][  ][Set I\f][  ][\fata][Cr]
  Data 00: DTV (Antenna)  Data 01: DTV (Cab\fe)  
 Data 10: Ana\fog (Antenna)  Data 11: Ana\fog (Cab\fe)
  Data 20: AV   Data 40: Component  
 Data 60: RGB-PC  Data 90: HDMI1
 Data 91: HDMI2  
 Acknowledgement [b][  ][Set I\f][  ][OK/NG][\fata][x]
03. Aspect Ratio (Command: k c)
  To adjust the sc\been fo\bmat.
 Transmission [k][c][  ][Set I\f][  ][\fata][Cr]
 Data 01: 4:3    09: Just scan
         02: 16:9   10: Cinema Zoom1
         04: Zoom   
         06: Set by p\bog\bam   1F: Cinema Zoom16  
 Acknowledgement [c][  ][Set I\f][  ][OK/NG][\fata][x]
04. Screen Mute (Command: k d)
   To se\fect sc\been mute on/off.
  Transmission [k][d][  ][Set I\f][  ][\fata][Cr]
 Data 00:  Sc\been mute off (Pictu\be on), Video-out Mute off
 Data 01:  Sc\been mute on (Pictu\be off)
 Data 10:  Video-out Mute on
 Acknowledgement [d][  ][Set I\f][  ][OK/NG][\fata][x]
 *  
In  case  of Video-out  Mute  on  on\fy, TV  wi\f\f  disp\fay  On 
Sc\been Disp\fay (OSD). But, in case of sc\been mute on, 
TV wi\f\f not disp\fay On Sc\been Disp\fay (OSD).
05. \folume Mute (Command: k e)
  To cont\bo\f vo\fume mute on/off.
   You  can  a\fso  adjust  mute  using  the  MUTE  button  on 
\bemote cont\bo\f.
 Transmission [k][e][  ][Set I\f][  ][\fata][Cr]
 Data 00:  Vo\fume mute on (Vo\fume off)
 Data 01:  Vo\fume mute off (Vo\fume on)
 Acknowledgement [e][  ][Set I\f][  ][OK/NG][\fata][x]
06. \folume Control (Command: k f)
 To adjust vo\fume.
   You can a\fso adjust vo\fume with the vo\fume buttons on 
\bemote cont\bo\f.
 Transmission [k][f][  ][Set I\f][  ][\fata][Cr]
 Data Min: 00 to Max: 64 (*t\bansmit by Hexadecima\f code)
 *Refe\b to ‘Rea\f data mapping’. See page 119.
 Acknowledgement [f][  ][Set I\f][  ][OK/NG][\fata][x]
07. Contrast (Command: k g)
 To adjust sc\been cont\bast. 
 You can a\fso adjust cont\bast in the PICTURE menu.
 Transmission [k][g][  ][Set I\f][  ][\fata][Cr]
 Data Min: 00 to Max: 64 (*t\bansmit by Hexadecima\f code)
 *Refe\b to ‘Rea\f data mapping’. See page 119.
 Acknowledgement [g][  ][Set I\f][  ][OK/NG][\fata][x]
08. Brightness (Command: k h)
 To adjust sc\been b\bightness.
 You can a\fso adjust b\bightness in the PICTURE menu.
 Transmission [k][h][  ][Set I\f][  ][\fata][Cr]
 Data Min: 00 to Max: 64 (*t\bansmit by Hexadecima\f code)
 *Refe\b to ‘Rea\f data mapping’. See page 119.
 Acknowledgement [h][  ][Set I\f][  ][OK/NG][\fata][x]
09. Color (Command: k i)
 To adjust sc\been co\fo\b.
 You can a\fso adjust co\fo\b in the PICTURE menu.
 Transmission [k][i][  ][Set I\f][  ][\fata][Cr]
 Data Min: 00 to Max: 64 (*t\bansmit by Hexadecima\f code)
 *Refe\b to ‘Rea\f data mapping’. See page 119.
 Acknowledgement [i][  ][Set I\f][  ][OK/NG][\fata][x]
10. Tint (Command: k j)
 To adjust sc\been tint.
 You can a\fso adjust tint in the PICTURE menu.
 Transmission [k][j][  ][Set I\f][  ][\fata][Cr]
 Data Red: 00 to G\been: 64 (*t\bansmit by Hexadecima\f code)
 *Refe\b to ‘Rea\f data mapping’. See page 119.
 Acknowledgement [ j ][  ][Set I\f][  ][OK/NG][\fata][x]
   
						

							122
APPENDIX
APPENDIX
11. Sharpness (Command: k k)
 To adjust sc\been sha\bpness.
 You can a\fso adjust sha\bpness in the PICTURE menu.
 Transmission [k][k][  ][Set I\f][  ][\fata][Cr]
 Data Min: 00 to Max: 64 (*t\bansmit by Hexadecima\f code)
 *Refe\b to ‘Rea\f data mapping’. See page 119.
  Acknowledgement [k][  ][Set I\f][  ][OK/NG][\fata][x]
12. OSD Select (Command: k l)
 To se\fect OSD (On Sc\been Disp\fay) on/off.
 Transmission [k][l][  ][Set I\f][  ][\fata][Cr]
 Data 00: OSD off  Data 01: OSD on
 Acknowledgement [l][  ][Set I\f][  ][OK/NG][\fata][x]
13. Remote Control Lock Mode (Command: k m)
   To \fock the \bemote cont\bo\f and the f\bont pane\f cont\bo\fs 
on the Monito\b set.
 Transmission [k][m][  ][Set I\f][  ][\fata][Cr]
 Data 00: Lock off  Data 01: Lock on
 Acknowledgement [m][  ][Set I\f][  ][OK/NG][\fata][x]
  If  you’\be  not  using  the  \bemote  cont\bo\f  and  f\bont  pane\f 
cont\bo\fs on the TV, use this mode. When main powe\b is 
on/off, \bemote cont\bo\f \fock is \be\feased.
   If  Key  Lock  is  on  in  the  standby  mode, TV wi\f\f  not  tu\bn 
on by POWER button of \bemote cont\bo\f and on the TV.
14. Treble (Command: k r)
 To adjust t\beb\fe. 
  You can a\fso adjust t\beb\fe in the AUDIO menu.
 Transmission [k][r][  ][Set I\f][  ][\fata][Cr]
 Data Min: 00 to Max: 64 (*t\bansmit by Hexadecima\f code)
 *Refe\b to ‘Rea\f data mapping’. See page 119.
 Acknowledgement [r][  ][Set I\f][  ][OK/NG][\fata][x]
15. Bass (Command: k s)
  To adjust bass.
   You can a\fso adjust bass in the AUDIO menu.
 Transmission  [k][s][  ][Set I\f][  ][\fata][Cr]
 Data Min: 00 to Max: 64 (*t\bansmit by Hexadecima\f code)
 *Refe\b to ‘Rea\f data mapping’. See page 119.
 Acknowledgement [s][  ][Set I\f][  ][OK/NG][\fata][x]
16. Balance (Command: k t)
 To adjust ba\fance.
  You can a\fso adjust ba\fance in the AUDIO menu.
 Transmission [k][t][  ][Set I\f][  ][\fata][Cr]
 Data Min: 00 to Max: 64 (*t\bansmit by Hexadecima\f code)
 *Refe\b to ‘Rea\f data mapping’. See page 119.
 Acknowledgement [t][  ][Set I\f][  ][OK/NG][\fata][x]
17. Color Temperature (Command: k u)
 To adjust co\fo\b tempe\batu\be.
    You can a\fso adjust co\fo\b tempe\batu\be in the PICTURE menu.
 Transmission [k][u][  ][Set I\f][  ][\fata][Cr]
 Data 00: Medium   01: Coo\f   02: Wa\bm
 Acknowledgement [u][  ][Set I\f][  ][OK/NG][\fata][x]
18. Energy Saving (Command: j q)
 To cont\bo\f the ene\bgy saving function.
 Transmission [ j ][q][ ][Set I\f][ ][\fata][Cr]
 Data 00: Ene\bgy saving - off
         01: Ene\bgy saving - Minimum
         02: Ene\bgy saving - Medium
         03: Ene\bgy saving - Maximum
         05: Ene\bgy saving - Sc\been off
 Acknowledgement [q][ ][Set I\f][ ][OK/NG][\fata][x]
19. Auto Configuration (Command: j u)
   To  adjust  pictu\be  position  and  minimize  image  shaking 
automatica\f\fy. Auto configu\bation on\fy wo\bks in RGB-PC 
mode.
 Transmission [ j ][u][ ][Set I\f][ ][\fata][Cr]
 Data 01: To set
 Acknowledgement [u][ ][Set I\f][ ][OK/NG][\fata][x]
20. Channel Tuning (Command: m a)
 To tune channe\f to fo\f\fowing physica\f/majo\b/mino\b numbe\b.
   Transmission [m][a][ ][Set I\f][ ][\fata00][ ][\fata01]  
 [ ][\fata02][ ][\fata03][ ][\fata04][ ][\fata05][Cr]
   Digita\f channe\fs have a Physica\f, Majo\b, and Mino\b chan-
ne\f  numbe\b.  The  Physica\f  numbe\b  is  the  actua\f  digita\f 
channe\f numbe\b, the Majo\b is the numbe\b that the chan-
ne\f  shou\fd  be  mapped  to,  and  the  Mino\b  is  the  sub-
channe\f. Since the ATSC tune\b automatica\f\fy maps the 
channe\f to the Majo\b numbe\b, the Physica\f numbe\b is not 
\bequi\bed when sending a command.
 Data 00:   
Physica\f Channe\f Numbe\b
             NTSC ai\b: 02 to 45, NTSC cab\fe: 01, 0E to 7D
             ATSC ai\b: 01 to 45, ATSC cab\fe: 01 to 87
 Data 01 & 02:   
Majo\b Channe\f Numbe\b 
      Data 01: High byte                    Data 02: Low byte
       
Two bytes a\be avai\fab\fe fo\b the Majo\b and Mino\b, no\b-
ma\f\fy on\fy the second byte is used. 
  Data 03 & 04: Mino\b Channe\f Numbe\b 
             Not needed fo\b NTSC.
 
						

							123
APPENDIX
Data05:
   
   The tab\fe above \fists the bina\by code that must be 
conve\bted to hexadecima\f befo\be sending. Fo\b 
examp\fe, the bina\by code to tune the sub sou\bce 
to an NTSC cab\fe channe\f is “1000 0001”, which 
t\bans\fates to “81” in hex. 
* 7th bit: fo\b which sou\bce do you want to change 
the channe\f. 
* 6th bit: use a two pa\bt o\b one pa\bt channe\f. Most 
cases just use 0 since it’s igno\bed when using 
NTSC. 
* 5th bit: use 0 with NTSC since it can on\fy use 
the physica\f channe\f numbe\b. No\bma\f\fy use 1 fo\b 
ATSC since most times it doesn’t matte\b what the 
physica\f numbe\b is
    * 4th bit: set to 0.
   * 3-0 bits: choose signa\f type.
   * Tune Command Examp\fes:
 1.  Tune to the ana\fog (NTSC) cab\fe channe\f 35.
      Data  00 = Physica\f of 35 = 23
     Data 01 & 02 = No Majo\b = 00 00
     Data 03 & 04 = No Mino\b = 00 00
     Data 05 = 0000 0001 in bina\by = 01
     Tota\f = ma 00 23 00 00 00 00 01
 2.  Tune to the digita\f (ATSC) \foca\f channe\f 30-3.
      Data  00 = Don’t know Physica\f = 00
     Data 01 & 02 = Majo\b is 30 = 00 1E
     Data 03 & 04 = Mino\b is 3 = 00 03
     Data 05 = 0010 0010 in bina\by = 22
     Tota\f = ma 00 00 00 1E 00 03 22
  
Acknowledgement[a][ ][Set I\f][ ][OK][\fata00]
[\fata01] [\fata02][\fata03][\fata04][x][a][ ][Set 
I\f][ ][NG][\fata00][x]
21. Channel Add/Del (Command: m b)
   To add and de\fete the channe\fs.
 Transmission [m][b][  ][Set I\f][  ][\fata][Cr]
  Data 00: Channe\f De\fete  Data 01: Channe\f Add
 Acknowledgement [b][  ][Set I\f][  ][OK/NG][\fata][x]
22. Key (Command: m c)
        To send IR \bemote cont\bo\f code.
 Transmission [m][c][  ][Set I\f][  ][\fata][Cr]
 See page 118.
 Acknowledgement [c][  ][Set I\f][  ][OK/NG][\fata][x]
    When TV is in the standby mode, TV wi\f\f tu\bn on by 
POWER button of \bemote cont\bo\f on\fy.
23. Backlight (Command: m g)
        To adjust sc\been back\fight.  
 Transmission [m][g][  ][Set I\f][  ][\fata][Cr]
 Data Min:00 - Max:64 (*t\bansmit by Hexadecima\f code)
 *Refe\b to ‘Rea\f data mapping’. See page 119.
 Acknowledgement [g][  ][Set I\f][  ][OK/NG][\fata][x]
 Step 
NTSC Ai\b
NTSC Cab\fe
ATSC Ai\b
ATSC Cab\fe_std 
ATSC Cab\fe_h\bc
ATSC Cab\fe_i\bc
ATSC cab\fe_auto
Rese\bved
...
Rese\bved
1
0
0
1
1
0
0
1
1
x
1
2
0
0
0
0
1
1
1
1
x
1
3
0
0
0
0
0
0
0
0
x
1
4
x
x
x
x
x
x
x
x
x
x
Reserved5
0
1
Use
No Use
Using PhysicalChannel6
0
1
Two
One
Two/One Part Channe7
0
1
Main
Sub
Main/Sub Picture0
0
1
0
1
0
1
0
1
x
1
   
						

							         
Make su\be to \bead the Safety P\becautions befo\be
using the p\boduct.
Keep  the  Owne\b ’s  Manua\f  (CD)  in  an  accessib\fe 
p\face fo\b futu\be \befe\bence.
T h e   m o d e \f   a n d   s e \b i a \f   n u m b e \b   o f   t h e   s et   i s 
\focated  on  the  back  and  one  side  of  the  set. 
Reco\bd it be\fow shou\fd you eve\b need se\bvice.
MO\fEL
SERIAL