LG Flatron L204wt Users Guide

Make sure to read the Important Precautionsbefore using the product. 
Keep the Users Guide(CD) in an accessible place for furture reference.
See the label attached on the product and give the information to your
dealer when you ask for service.
L204WT
L204WTM
L204WTQ
L204WTX
User’s Guide
 

A1
This unit has been engineered and manufactured to ensure your personal
safety, however improper use may result in potential electrical  shock or fire
hazards. In order to allow the proper operation of all safeguards
incorporated in this display, observe the following basic rules for its
installation, use, and servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another \
power
cord, make sure that it is certified by the applicable national standard\
s if not being...

A2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place the
display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release of
heat generated during operation. If these openings are blocked, built-up heat can
cause failures which...

A3
Connecting the speaker
1. 
Place the monitor with its front facing downward on a soft cloth.
2. nsert the protruding hook of the speaker in the direction of the slot in\
 the back of the product.
Connecting  the speakers - The feature is only for speaker models - L204WTM
DC-OUTD-SUB
DVI-D
AC-IN DC-OUT
D-SUB
DVI-D
AC-IN
DC-OUTD-SUB
DVI-D
AC-IN DC-OUT
D-SUB
DVI-D
AC-IN
Hook
Slot
Audio DC-In
CableAUDIO IN
3. After setting up the speaker, connect the Audio DC-In Cable to the back \
of the product. 
DC-OUT...

A4
Connecting the Display
Important
This illustration depicts the general model of connection. Your monitor may differ from
the items shown in the picture.
Once you connect the stand base, try not to disconnect it.
Do not carry the product upside down holding only the stand base. The product may
fall and get damaged or injure your foot.
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Connecting the stand 
1. 
Place the...

Connecting the Display
A5
1.Put a cushion or soft cloth on a flat surface.
To remove the Stand: 
2. Place the monitor face down on
the cushion or soft cloth.     
3.Hold the product as it follows and lift up the Stand slightly.
4.Change your hold on the product as it follows and turn the Stand Base in the arrow
direction.
5.Pull out the Stand to remove.
The Head part
The Stand 
base part
 

A6
Connecting the Display
To remove the Stand Base: 
2.
Hold the body of the Stand as it follows.
Type. A
3.Press inside the two long latches at the
same time with your strength as it follows.
5.The body of the Stand and the Stand Base are successfully separated.
4.Keep pressing the two latches and use the other
hand to hold the body of the Stand to push the
Stand Base in the arrow direction to remove.
1.Ensure there are two short and two long
latches at the bottom of the Stand Base.
 

Connecting the Display
A7
To remove the Stand Base: 
2. 
Hold the body of the Stand as it follows.
Type. B
3.Press inside the four latches individually toward each end.
4.Put the Stand Base on a flat surface and pull
up the body of the Stand while holding the
Stand Base with the other hand. to remove.5.The body of the Stand and the Stand
Base are successfully separated.
1.Ensure there are four latches at the
bottom of the Stand Base.
 

A8
Connecting the Display
20
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off. 
Positioning your display
1.Adjust the position of the panel in various ways for maximum comfort.
Tilt Range : -5˚~20˚                            
Ergonomic
It is recommended that in order to maintain an ergonomic and comfortable viewing
position, the forward tilt angle of the monitor should not exceed 5 degrees.
When adjusting the angle of the...

A9
4.Press        button on the front switch panel to turn the power on.When monitor power is turned on, the  Self Image Setting
Function is executed automatically.
(Only Analog Mode)
NOTE‘ Self Image Setting Function’?  This function provides the user with optimal display settings.When the u\
ser
connects the monitor for the first time, this function automatically adj\
usts the display to optimal settings for individual
input signals. If you want to adjust the monitor while in use, or wish t\
o manually...