LG Flatron L1942h Users Guide

Make sure to read the Important Precautions before using the product. 
Keep the User's Guide(CD) in an accessible place for future reference.\
See the label attached on the product and give the information to your
dealer when you ask for service.
L1942H
User’s Guide
 

A1
This unit has been engineered and manufactured to ensure your personal
safety, however improper use may result in potential electrical  shock or fire
hazards. In order to allow the proper operation of all safeguards
incorporated in this display, observe the following basic rules for its
installation, use, and servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another \
power
cord, make sure that it is certified by the applicable national standard\
s if not being...

A2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do n\
ot place the
display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kit\
chen sink,
laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow \
the release of
heat generated during operation. If these openings are blocked, built-up\
 heat can
cause failures...

A3
Connecting the Display
ImportantThis illustration depicts the typical connection procedure. Your monitor\
 may differ from
the one displayed in the pictures above.
Do not touch or apply force to the monitor's screen while expanding or f\
olding the
stand base.
Before setting up the monitor, ensure that the power to the monitor, the\
 computer
system, and other attached devices is turned off.
Unfolding the stand base 
1.Place the monitor with its front facing downward on a soft cloth.
2.Hold the...

A4
Connecting the Display
Folding the stand base
Ergonomic
It is recommended that in order to maintain an ergonomic and comfortable\
 viewing
position, the forward tilt angle of the monitor should not exceed 5 degr\
ees
1.Face the front of the monitor dislpay. Then gently push the monitor back\
wards,
following the sequence shown in the picture below.
Tilt range
1.Make sure that the angle of the panel is set for your comfort.
Tilt Range : 0˚~30˚
 

A5
Connecting the Display
To adjust the height
Scope of adjusting the height: maximum 4.16 inches (105.7 mm)
105.7 mm
 

A6
Using the Computer
1.Make sure to turn off the computer and  product. Connect the cable as be\
low sketch map
form to .1
2.Press        button on the side switch panel to turn the power on.
When monitor power is turned on, the Self Image Setting Function
is executed automatically.
(Only Analog Mode)
NOTE'Self Image Setting Function'?This function provides the user with optimal display settings.When the u\
ser
connects the monitor for the first time, this function automatically adj\
usts the...

Connecting the Display
A7
To arrange the cables
1.Insert and screw the cable holder into the hole in the back of the stand\
 until it will
not turn any more as shown in the following figure.
2.After connecting the cables neatly, arrange the cables to the Cable Hold\
er as shown
in the following figure.
Cable Holder
 

A8
Control Function
Control Panel Functions
MENU ButtonUse this button to enter or exit from the On Screen Display.
OSD LOCKED/UNLOCKED
This function allows you to lock the current control settings, so
that these settings are not inadvertently changed. To lock the
OSD settings, press and hold the MENU buttonfor several
seconds. The message " OSD LOCKED" appears.
You can unlock the OSD settings at any time by
pushing the  MENU button for several seconds. The
message " OSD UNLOCKED "...

A9
Control Panel Functions
This Indicator lights up as blue when the display is
operating normally(On Mode). If the display is in
Sleep Mode (Energy Saving), this indicator color
changes to flicker. Use this button to turn the display on or off.
Power Button
Power Indicator
Use this button to select an icon in the On Screen
Display.AUTO/SET
Button
AUTO IMAGE ADJUSTMENT
When adjusting your display settings, always press
the  AUTO/SET button prior to entering the On
Screen Display(OSD). This will...