LG Flatron L1933s Users Guide

Make sure \bo read \bhe\f Import\bnt Pre\f\butions \fefore using \bhe prod\fuc\b. 
Keep \bhe User's Gui\fde(CD) in an access\fi\fle place for fur\bur\fe reference.
See \bhe la\fel a\b\bache\fd on \bhe produc\b and g\five \bhe informa\bion \b\fo your
dealer when you ask \ffor service.
User’s Guide
L1753T 
L1\b53T
L1733TR
L1\b33TR
L1753TR
L1\b53TR
L1753TX
L1\b53TX
 

A1
This unit has been engineered and manufactured to ensure your personal
safety, however improper use may result in potential eletrical  shock or fire
hazards. In order to allow the proper operation of all safeguards
incorporated in this display, observe the following basic rules for its
installation, use, and servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided...

A2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place
the display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which...

Connecting the Display
A3
Important
This illustration depicts the general model of connection. Your monitor may differ from
the items shown in the picture.
Do not carry the product upside down holding only the stand base. The product may
fall and get damaged or injure your foot.
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Connecting the stand 
1. Place the monitor with its front facing downward on a soft cloth....

A4
Connecting the Display
1.Put a cushion or soft cloth on a flat surface.
To remove the Stand: 
2. Place  the  monitor  face  down  on
the cushion or soft cloth.     
3.Hold the product as it follows and lift up the Stand slightly.
4.Change your hold on the product as it follows and turn the Stand Base in the arrow
direction until you hear a "click."
5.Pull out the Stand to remove.
The Head part
The Stand 
base part
6ownloadedHfromH@anual@onitor)comH@anuals 

A5
Connecting the Display
To remove the Stand Base: 
1.
Hold  the  body  of  the  Stand  as  it
follows.
3.Put  the  Stand  Base  on  a  flat  surface  and
pull  up  the  body  of  the  Stand  while
holding  the  Stand  Base  with  the  other
hand. to remove.4.The  body  of  the  Stand  and  the  Stand
Base are successfully separated.
2.Press  the  two  latches  at  the  same
time as it follows.
6ownloadedHfromH@anual@onitor)comH@anuals 

A6
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off. 
Positioning your display
1.Adjust the position of the panel in various ways for maximum comfort.
Tilt Range:-5˚~20˚ Swivel :355˚
(The feature is not available for all countries)
Ergonomic
It is recommended that in order to maintain an ergonomic and comfortable viewing
position, the forward tilt angle of the monitor should not exceed 5 degrees.
When...

A7
2
Connecting the Display
Using the Computer
1.Place the monitor in a convenient, well-ventilated location near your computer. 2.Connect the signal cable      . When attached, tighten the thumbscrews to secure the 
connection.
3.Connect the power cord into a proper power outlet  that is easily accessible and close to
the display.
Wall-outlet type
PC-outlet type
DVI-D(This feature is not available in all countries.)
MACPC
Power CordSignal Cable
Analog signalD-subDigital signalDVI
Varies according to...

A8
Control Panel Functions
MENU ButtonUse this button to enter or exit the On Screen Display.
Control Function
OSD LOCKED/UNLOCKED
This function allows you to lock the current control
settings, so that they cannot be inadvertently changed.
Press and hold the MENU buttonfor several seconds.
The message "OSD LOCKED"should appear.
You can unlock the OSD controls at any time by pushing
the MENU buttonfor several seconds. The message
"OSD UNLOCKED"should appear.
ButtonsUse these buttons to...

A9
Control Panel Functions
This Indicator lights up blue when the display
operates normally(On Mode). If the display is in Sleep
Mode (Energy Saving), this indicator color changes 
to amber. Use this button to turn the display on or off.
Power Button
Power Indicator
Use this button to enter a selection in the On Screen 
Display.AUTO/SET
Button
AUTO IMAGE ADJUSTMENT
When adjusting your display settings, always press
the AUTO/SETbutton before entering the On Screen
Display(OSD). This will automatically...