LG Flatron E2341t Owners Manual

1
This unit has been engineered and manufactured to ensure your personal s\
afety,
however improper use may result in potential electrical  shock or fire h\
azards. In
order to allow the proper operation of all safeguards incorporated in th\
is display,
observe the following basic rules for its installation, use, and servici\
ng.
On Safety
Use only the power cord supplied with the unit. In case you use another \
power
cord, make sure that it is certified by the applicable national standard\
s if not...

2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do n\
ot place the
display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kit\
chen sink,
laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow \
the release
of heat generated during operation. If these openings are blocked, built\
-up heat
can cause failures...

Important Precautions
3
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on\
 the displayscreen because over-spraying may cause electrical shock.
When cleaning the product, unplug the power cord and scrub gently with a\
 soft cloth to prevent scratching. Do not clean with a wet cloth or spray wate\
r or other
liquids directly onto the product. An electric shock may occur. (Do not\
 use
chemicals such as...

4
Accessories
!!! Thank for selecting LGE products !!! 
Please make sure the following items are included with your
monitor. If any items are missing, contact your dealer.
Users Guide/CardsPower Cord
15-pin D-Sub Signal Cable
(To set it up, this signal cable may be attached to  this product before shipping out.)DVI-D Signal Cable
(This feature is not available in all countries.)
NOTEThis accessories may look different from those shown here.User must use shielded signal interface cables (D-sub 15 pin...

Connecting the Display
5
Before setting up  the monit or, ensure that the pow er to the moni tor, the computer
syste m, and other attache d devices is turned off.
Connecting the st and 
1.Place  the  monit or with i ts front facing  downwardon a soft cloth.
2. Assemble the stand Body into  the
product in the correct direction a s shown in
t he  picture.  Make sure you  push it until you
hear i t “click”.3.Assemble the Stand Base(Front,
Rear) into the Stand Body in the
correct direction.
4.Use a coin on...

6
Connecting the Display
Disassembling the  stand
1.Put a cushion  or soft cloth  on aflat
s urface.
3.                                                        4. Remove  the Stand Body  and Stand
Base from product in correct 
direction as shown in the picture.
2.P lace the  monitor face  Down on the
c ushion  or soft cloth.
Use a coin on the back of the Stand
Base and turn the screw  anticlock-
wise to loosen.
 

7
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor,
the computer system, and other attached devices is turned off. 
Positioning your display
-After installation, adjust the angle as shown below. 
1.Adjust the position of the panel in various ways for maximum comfort.
Tilt Range :  -5˚ to 15˚
ERGONOMIC
It is recommended that in order to maintain an ergonomic and comfortable\
 viewing position,
the forward tilt angle of the monitor should not exceed 5 degrees.
Do...

8
Connecting the DisplayE2241V/E2341V/E2341VG/E2441V
N
OTE
‘ S
 elf Image S
etting Funct ion’? This f unct ion provides the  user with optimal display
sett ings.W hen the  user connects the  monitor for the f irst time , this f unct ion aut omatically  adjusts
the  display to opt imal settings for individual  input signals. 
‘AU TO’ Funct ion? When  you enc ounter problems  such as blurry screen,  blurred lett ers, screen
f licker or tilted  screen while using the  device or after  changing screen...

9
Control Panel Functions
Front Panel  Controls
MENU ButtonOSD  LOCKED/ UNLOCKED
T his funct ion allows  you to lock the current control
se ttings, so that they cannot be  inadvertent ly changed.
P ress and  hold the MENU button for  several  seconds.
T he  mess age OSD  LOCKED should  appear.
Y ou can  unlock the OSD  controls a t any time  by pus hing
the  MENU button for  several  seconds. The  message
 OSD  UNLOCKED should  appear.
For D-SUB and DVI input
Only for HDMI input