LG Flatron E2210t Owners Manual

www.lg.com
OWNER’S MANUAL
LCD MONITOR 
LCD MONITOR MODEL
E1910PM
E2210PM
Please  read  this  manual  carefully  before  operating  your  set  and 
retain it for future reference.
ENGLISH
   

1
This unit has been engineered and manufactured to ensure your personal safety,
however improper use may result in potential electrical  shock or fire hazards. In
order to allow the proper operation of all safeguards incorporated in this display,
observe the following basic rules for its installation, use, and servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided...

2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place the
display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which may...

Important Precautions
3
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display
screen because over-spraying may cause electrical shock.
When cleaning the product, unplug the power cord and scrub gently with a soft
cloth to prevent scratching. Do not clean with a wet cloth or spray water or other
liquids directly onto the product. An electric shock may occur. (Do not use
chemicals such as benzene,...

4
Accessories
!!! Thank for selecting LGE products !!! 
Please make sure the following items are included with your
monitor. If any items are missing, contact your dealer.
Users Guide/CardsPower Cord
15-pin D-Sub Signal Cable
(To set it up, this signal cable may be
attached to  this product before
shipping out.)DVI-D Signal Cable
(This feature is not available in all
countries.)
NOTEThis accessories may look different from those shown here.
User must use shielded signal interface cables (D-sub 15 pin...

Connecting the Display
5
Before setting up the monitor, ensure that the power to the monitor,
the computer system, and other attached devices are turned off. 
Connecting the stand base or Removing the stand base
1. Place the monitor with its front facing downward on a cushion or soft cloth.
2.Assemble the Stand Base into the Stand Body.
Be sure dont pull out the Stop Pin and make the Stand Base direction as shown. 
WARNING The tape and locking pin may only be removed from those monitors equipped with a...

6
Connecting the Display
IMPORTANTThis illustration depicts the general model of connection. Your monitor may differ from the items
shown in the picture.
Do not carry the product upside down holding only the stand base. The product may fall and get
damaged or injure your foot.
3.Use a coin on the back of the stand base and turn the screw clockwise to tighten.
4.Lift and turn the monitor to face towards the front after the connection is 
made to the female part of the cable youre attaching.
5.When you...

7
Connecting the Display
Height Range : maximum 4.33 inches (110.0 mm)
* Please be sure to       
remove the Locking 
pin to adjust the height.   
110.0 mm
ERGONOMIC
It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt
angle of the monitor should not exceed 5 degrees.
WARNINGYou do not need to replace the Locking pin  after it is removed, to adjust its height. 
When adjusting the angle of the screen, do not put your finger(s) in
between the head of...

8
Connecting the Display
-The pivot function allows you to rotate the screen 90 degrees clockwise. 
1.Lift the monitor to its highest height to utilize the Pivot function.
2.Landscape & Portrait : You can rotate the panel 90o  clockwise. 
Please be cautious and avoid contact between the monitor head and the
Stand Base when rotating the screen to access the Pivot function. If the
monitor head touches the Stand Base, then the Stand Base could crack.
3.Be careful with the cables when rotating the screen....

9
Connecting the Display
NOTE‘ Self Image Setting Function’? This function provides the user with optimal display
settings.When the user connects the monitor for the first time, this function automatically adjusts
the display to optimal settings for individual input signals. 
‘AUTO’ Function? When you encounter problems such as blurry screen, blurred letters, screen
flicker or tilted screen while using the device or after changing screen resolution, press the
AUTO function button to improve resolution....