LG Flatron E2210s Owners Manual

20
On Screen Display(OSD) Selection and Adjustment (Only E2210PM)
Main menu Sub menu Description
Change the input image signal ratio to
original. 
WIDE
ORIGINALSwitch to full screen mode according to
input image signal.  
* This function works only if input
resolution is lower than monitor ratio
(16:10).
Exit: Exit,     : Move: Select another sub-menu
 

On Screen Display(OSD) Selection and Adjustment 
21
Main menu Sub menu Description
When PHOTO EFFECT is not NORMAL,CONTRAST can not be selected and
COLOR is grey.When COLOR is selected down, PHOTO EFFECT is back to
NORMAL and CONTRAST can be selected now.
PHOTO EFFECT and F-ENGINE should not be unnormal at the same time.
NORMALThe Photo Effect function is disabled.
GAUSSIAN
BLURThis menu changes the screen to be more
colorful and smoother. 
E1910PM
E2210PM
E1910PM
E2210PM
 

22
On Screen Display(OSD) Selection and Adjustment 
Main menu Sub menu Description
Exit: Exit,     : Move: Select another sub-menu
SEPIAThis menu changes the screen to be
Sepia tone (brown color). 
MONOCH
-ROMEThis menu changed the screen to be
Gray tone(black-and-white Picture) .
E1910PM
E2210PM
E1910PM
E2210PM
 

23
Troubleshooting
No image appears
Check the following before calling for service.
No image appears
Do you see a OSD LOCKED message on the screen?
Is the power cord of the
display connected?
Is the power indicator
light on?
Is the power indicator
flickering?
Do you see an OUT OF
RANGE message on
the screen?
Do you see a CHECK
SIGNAL CABLE
message on the
screen?• Check and see if the power cord is connected
properly to the power outlet.
• Press the Power button.
• If the display is in power saving...

24
Troubleshooting
Display image is incorrect
Display Position is
incorrect.
On the screen
background, vertical
bars or stripes are
visible.
Any horizontal noise
appearing in any
image or characters
are not clearly
portrayed.• Press the AUTObutton to automatically adjust
your display image to the ideal setting. 
If the results are unsatisfactory, adjust the image
position using the H position and V positionicon
in the on screen display.
• Press the AUTObutton to automatically adjust
your display image...

25
Display image is incorrect
Troubleshooting
The screen color is
mono or abnormal.
The screen blinks.• Check if the signal cable is properly connected
and use a screwdriver to fasten if necessary.
• Make sure the video card is properly inserted in
the slot.
• Set the color setting higher than 24 bits (true color)
at Control Panel - Settings.
• Check if the screen is set to interlace mode and if
yes, change it to the recommend resolution.
Do you see an Unrecognized monitor, Plug&Play (VESA
DDC) monitor...

26
Specifications                                                                 E1910PM
Tilt -4˚ to 16˚
Swivel                356˚
Height              110 mm / 4.33 inchRange
48.2 cm (19 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating 
Visible diagonal size : 48.2cm
0.294 x 0.294 mm (Pixel pitch)
Display
Horizontal Freq. 30 kHz to 83 kHz (Automatic)
Vertical Freq. 56 Hz to 75 Hz (Automatic)
Input Form Separate Sync.
DigitalSync Input
Signal Input 15 pin D-Sub Connector
DVI-D Connector...

27
Specifications                                                                 E2210PM
55.8 cm (22 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating 
Visible diagonal size : 55.8cm
0.282 x 0.282 mm (Pixel pitch)
Display
Horizontal Freq. 30 kHz to 83 kHz (Automatic)
Vertical Freq. 56 Hz to 75 Hz (Automatic)
Input Form Separate Sync.
DigitalSync Input
Signal Input 15 pin D-Sub Connector
DVI-D Connector (Digital)
Input Form RGB Analog (0.7 Vp-p/ 75 ohm), DigitalVideo Input
Max VESA 1680 x 1050...

28
Indicator
On Mode
Sleep Mode
Off ModeWhite
White Blinking
Off
LED Color
MODE
Specifications
Preset Modes (Resolution)
Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)
*Recommend Mode
E2210PM
1
2
3
4
5
6
7
8
9
10
*11720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
1024 x 768
1024 x 768
1152 x 864
1280 x 1024
1280 x 1024
1680 x 105031.468
31.469
37.500
37.879
46.875
48.363
60.123
67.500
63.981
79.976
65.29070
60
75
60
75
60
75
75
60
75
60
Display Modes (Resolution) Horizontal Freq....

29
Installing the Wall mount plate
This monitor satisfies the specifications of the  Wall mount plate or
the interchange device.
1. After moving the product to face
downward, make sure to place it on a
soft cloth or a cushion to avoid surface
damage.  
2. Separate the head and the stand with
the use of a screwdriver.