LG Flatron E1910t Owners Manual

www.lg.com
OWNER’S MANUAL
LCD MONITOR 
LCD MONITOR MODEL 
E1910T
Pl ease  re ad  this  manual  c a re fully  be fo re  ope ra ting  y our  s e t  an d 
retain it for future reference.
ENGLISH
E2 210S
E2
210T
E1 910S 
   

1
This unit has been engineered and manufactured to ensure your personal safety,
however improper use may result in potential electrical  shock or fire hazards. In
order to allow the proper operation of all safeguards incorporated in this display,
observe the following basic rules for its installation, use, and servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided...

2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place the
display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which may...

Important Precautions
3
On Cleaning
Unplug the display before cleaning the face of the display screen. 
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on\
 the displayscreen because over-spraying may cause electrical shock.
When cleaning the product, unplug the power cord and scrub gently with a\
 soft cloth to prevent scratching. Do not clean with a wet cloth or spray wate\
r or other
liquids directly onto the product. An electric shock may occur. (Do not\
 use
chemicals such as...

4
Accessories
!!! Thank for selecting LGE products !!! 
Please make sure the following items are included with your
monitor. If any items are missing, contact your dealer.
Users Guide/CardsPower Cord
15-pin D-Sub Signal Cable
(To set it up, this signal cable may be
attached to  this product before
shipping out.)DVI-D Signal Cable
(This feature is not available in all
countries.)
(Only 
E1910T/E2210T)
NOTEThis accessories may look different from those shown here.User must use shielded signal interface...

Connecting the Display
5
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Connecting the stand 
1.Place the monitor with its front facing downward on a soft cloth.
2. Assemble the Stand Body into the
product in the correct direction as shown in
the picture. Make sure you push it until you
hear it “click”.3.Assemble the Stand Base(Front,
Rear) into the Stand Body in the
correct direction.
4.Tie down the base lock to...

6
Connecting the Display
..
Disassembling the stand
1.Put a cushion or soft cloth on aflat
surface.
3.Change your lock on the product as it follows and turn it in the arrow direction.
2.Place the monitor face Down on the
cushion or soft cloth.
If you cant release the stand base even the locking knob is at a release
position, Please push the indicated knob down and retry it.
 

7
Connecting the Display
4.Pull out the Stand to remove.
5.Pushing the PUSH button, Take the stand body from hinge body.
Good Position Bad Position
Warning:
You can hurt your finger.
 

8
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor,
the computer system, and other attached devices is turned off. 
Positioning your display
-After installation, adjust the angle as shown below. 
1.Adjust the position of the panel in various ways for maximum comfort.
Tilt Range : -5˚ to 15˚
ERGONOMIC
It is recommended that in order to maintain an ergonomic and comfortable viewing position,
the forward tilt angle of the monitor should not exceed 5 degrees.
Do not...

9
Connecting the DisplayE1910T/E2210T
NOTE‘ Self Image Setting Function’? This function provides the user with optimal display
settings.When the user connects the monitor for the first time, this function automatically adjusts
the display to optimal settings for individual input signals. 
‘AUTO’ Function? When you encounter problems such as blurry screen, blurred letters, screen
flicker or tilted screen while using the device or after changing screen resolution, press the
AUTO function button to improve...