LG F 1443kds Owners Manual

OWNER’S MANUAL
WASHING MACHINE 
F1443KDS(1~9)
P/No. : MFL63288756
Please read this manual carefully before operating
your washing machine and retain it for future reference.
www.lg.com
 

ontentsC

2
Contents..................\s..................\s2
\brodu\ft features ..................\s.....3
Warnings
Imp\brta\ft safety i\fstruc\sti\b\fs .................4\s
Save these i\fstructi\b\fs\s ..................\s.......4
Spe\fifi\fations ..................\s.........5
Installation
Rem\bvi\fg packi\fg ..................\s..............6
Rem\bvi\fg tra\fsit b\blts ..................\s........6
I\fstallati\b\f place req\suireme\fts .............7
C\b\f\fecti\fg water supply \sh\bse...

ˆ¡…–¯ˆ ¿„
Inverter Direct Drive system
The advanced Brushless DC motor directly drives the drum without 
belt and pulley.
Low noise speed control system
By sensing the amount of load and balance, it evenly distributes load
to minimize the spinning noise level.
Child Lock
The Child Lock prevents children from pressing any button to change
the settings during operation.
More economical with Intelligent Wash system
Intelligent Wash System detects the size of load and water temperature,
and then...

4
arningsW
For your safety, the information in this manual must be followed to minimize the risk
of fire or explosion, electric shock, or to prevent property damage, personal injury, or
loss of life.                   
READ ALL INSTRUCTIONS AND EXPLANATION OF THE INSTALLATION BEFORE USE 
WARNING!
• Before installation, check exterior damages. 
If it has, do not install. 
• Do not install or store the washer where it will 
be exposed to the weather.
• Do not tamper with controls.
• Do not repair or...

■Name  : Front loading washing machine
■Power supply  : 220 - 240 V~, 50 Hz
■Size  : 600 mm(W) 640 mm(D) 850 mm(H)
■Weight : 70 kg
■Max.Watt   : 2200W (Wash) / 1100W (Steam)
■Wash capacity : 11 kg
■Water consumption  : 77 l (7 l / kg)
■Permissible water pressure : 100 ~ 1000 kPa (1.0 ~ 10.0 kgf / cm
2)
The appearance and specifications may vary without notice to improve the quality 
of the unit.
5
pecificationsS
란제리
1%RinseTe m p .40
°C
31:1
5Re
sttidWashing
Spanner
■Accessories
Drawer
(For detergent...

6
nstallationI
■Removing packing
Base Packing
Washer
Spanner
1. Remove the cardboard box and
styrofoam packing.
2. Lift the washing machine and remove
the base packing.
3. Remove the tape securing the power
supply cord and drain hose.
4. Remove the inlet hose from the drum.
1. Unscrew the 3 bolts with 
the spanner supplied.
2. Take out the 3 bolts along with the
rubber bungs by slightly twisting the
bung. 
3. Close the holes with the caps supplied.Keep the transit bolts for future
use.  To prevent...

7
nstallationI
Laundry
Tub Washer
approx.
2cmDrain Hose
• Level floor :
Allowable slope under entire washer is 1˚
• Power outlet :
Must be within 1.5 meters of either side of location of washer.
Do not overload the outlet with more than one appliance.
• Additional Clearance :
For Wall, 10cm:rear / 2cm : right & left side
Do not place or store laundry products on top of washer at
any times. 
They can damage the finish or controls.
■Installation place requirement
Positioning
Location
• Install the washer...

8
nstallationI
CAUTION concerning the Power cord
Most appliances recommend they be placed upon a dedicated circuit; that is, a single
outlet circuit which powers only that appliance and has no additional outlets or branch
circuits. Check the specification page of this owners manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets,
extension cords, frayed power cords, or damaged or cracked wire insulation are
dangerous. Any of these conditions could...

9
nstallationI
1. Unscrew the adapter ring plate and the 4
adapter retaining screws.
2. Push the adapter onto the end of the tap
so that the rubber seal forms a watertight
connection. Tighten the adapter ring plate
and the 4 screws.
3. Push the water supply hose vertically
upwards so that the rubber packing within
the hose can adhere completely to the
tap and then tighten it by screwing it to
the right. • Water supply pressure must be between 100 kPa and 1000 kPa (1.0 ~ 10.0 kgf / cm
2)
• Do not strip or...

10
1. Unscrew the adapter ring plate and 
the 4 adapter retaining screws.
2. Remove the guide plate if the tap is 
too large to fit the adapter.
3. Push the adapter onto the end of 
the tap so that the rubber seal forms 
a watertight connection. 
Tighten the adapter ring plate and 
the 4 screws.
4. Pull the connector latch plate down,
push the inlet hose onto the adapter,
and release the connector latch plate. 
Make sure the adapter locks into place.
nstallationI
After completing connection, if water...