LG E2242tc Owners Manual

www.lg.com
OWNER’S MANUAL
LED LCD MONITOR
E1942TC
E2042TC
E2242TC
E2442TC
Ple\fse re\fd \bhis m\fnu\fl c\frefully before oper\f\bing 
your se\b \fnd re\b\fin i\b for fu\bure reference.
LE\f LC\f MONITOR MO\fEL
ENGLISH
 

2
ENGENGLISH
TABLE OF CONTENTS
CONTENTS
3	 ASSEMBLING	AND	PREPAR-
ING
3	 Unpacking
4	 Parts	and	buttons
5	 Setting	up	the	Monitor	set	
5	 -	 Attaching	the	Stand	Base
5	 -	 Detaching	the	Stand	Base	
6	 -	 Mounting	on	a	table
6	 -	 Using	the	cable	holder
8	 -	 Mounting	on	a	wall
9	 USING	THE	MONITOR	SET
9	 Connecting	to	a	PC
9	 -	 D-SUB	connection
9	 -	 DVI-D	connection
11	 CUSTOMIZING	SETTINGS
12	 Customizing	Settings
12	 -	 Menu	Settings
13			-	PICTURE
14			-	COLOR
15			-	DISPLAY
16			-	OTHERS
17	 SUPER...

3
ENGENGLISH
ASSEMBLING AND P\fEPA\fING
ASSEMBLING	AND	PREPARING
Unpacking
Check	your	product	box	for	the	following	items.	If	there	are	any	missing	accessories,	contact	the	local	
dealer	where	you	purchased	 your	product. 	The	 illustrations	 in	this	 manual	 may	differ	 from	the	actual	 product	
and	accessories.
yyDo	not	use	any	unapproved	accessories	to	ensure	the	safety	and	product	life	span.
yyAny	damages	or	injuries	by	using	unapproved	accessories	are	not	covered	by	the	warranty.	
yyThe	accessories...

4
ENGENGLISH
ASSEMBLING AND P\fEPA\fING
Parts	and	buttons
Power	Indicator
yyLighting	On: 	Turned 	on
yyLighting 	Off: 	Turned 	off
Connection	panel	(See	p.9)
Button	(See	p.11)
(Power	Button)
  

5
ENGENGLISH
ASSEMBLING AND P\fEPA\fING
Attach	the	Stand	Body	to	the	monitor	set.
Attach	the	Stand	Base.
Tighten	the	screw	to	the	right	with	a	coin.
Setting	up	the	Monitor	set	
Attaching	the	Stand	Base
1	 Place	the	Monitor	set	with	the	screen	side	
down	on	a	flat	and	cushioned	surface.
Lay	a	foam	mat	or	soft	protective	cloth	
on	the	surface	to	protect	the	screen	from	
damage.
CAUTION
2	
Stand	Base
Stand	Body
1
2
3
yyThis	illustration	depicts	the	general	model	of	
connection.	Your	monitor	may	differ	from...

6
ENGENGLISH
ASSEMBLING AND P\fEPA\fING
Mounting	on	a	table
1	 Lift	and	tilt	the	Monitor	set	into	its	upright	
position	on	a	table.
Leave	a	10	cm	(minimum)	space	from	the	wall	
for	proper	ventilation.
Using	the	cable	holder
2	 Connect	the	AC-DC	Adapter	and	Power	Cord	
to	a	wall	outlet.
3	 Press	(Power)	button	on	the	bottom	switch	
panel	to	turn	the	power	on.
\b0 cm
\b0 cm
\b0 cm
\b0 cm
Unplug	the	power	cord	before	moving	the	
Monitor	to	another	location.	Otherwise	electric	
shock	may	occur.
CAUTION
Cable...

7
ENGENGLISH
ASSEMBLING AND P\fEPA\fING
Using	the	Kensington	security	system	
The	Kensington	security	system	connector	is	
located	at	the	back	of	the	Monitor	set.	For	more	
information	of	installation	and	using,	refer	to	the	
manual	supplied	with	the	Kensington	security	
system	or	visit	http://www.kensington.com.
Connect	the	Kensington	security	system	cable	
between	the	Monitor	set	and	a	table.
The	Kensington	security	system	is	optional.	
You	can	obtain	it	from	most	electronics	stores.
NOTE
When	you...

8
ENGENGLISH
ASSEMBLING AND P\fEPA\fING
Mounting	on	a	wall
For	proper	ventilation,	allow	a	clearance	of	10	cm	
on	each	side	and	from	the	wall.	Detailed	
instructions	are	available	from	your	dealer,	see	the		
optional	Tilt	Wall	Mounting	Bracket	Installation	and
Setup	Guide.
If	you	intend	to	mount	the	Monitor	set	to	a	wall,	
attach	Wall	mounting	interface	(optional	parts)	to	
the	back	of	the	set.
When	you	install	the	Monitor	set	using	a	wall	
mounting	interface	(optional	parts),	attach	it	
carefully	so	it...

9
ENGENGLISH
USING THE MONITO\f SET
USING	THE	MONITOR	SET
Connecting	to	a	PC
yyYour	Monitor	set	supports	Plug	&	Play*.	
*Plug	&	Play:		A	PC	recognizes	a	connected	
device	that	users	connect	to	a	PC	and	turn	
on,	without	device	configuration	or	user	
intervention.
D-SUB	connection
Transmits	analog	video	from	your	PC	to	the	
Monitor	set.	Connect	the	PC	and	the	Monitor	set	
with	the	supplied	D-sub	15	pin	signal	cable	as	
shown	in	the	following	illustrations.
yyMac	adapter
For	 Apple	Macintosh	use,	a...

\b0
ENGENGLISH
USING THE MONITO\f SET
yyWhen	you	want	to	use	two	PC	in	our	Monitor,	
please	connect	the	signal	cable(D-SUB/
DVI-D)	respectively	in	Monitor	set.
yyIf	you	turn	the	Monitor	set	on	while	it	is	cold,	
the	screen	may	flicker.	This		is	normal.
yySome	red,	green,	or	blue	spots	may	appear	
on	the	screen.	This	is	normal.
yy"Self	Image	Setting"	Function.
This	function	provides	the	user	with	optimal	
display	settings.When	the	user	connects	
the	monitor	for	the	first	time,	this	function...