LG Cf181d Locos Projector User Manual
Have a look at the manual LG Cf181d Locos Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1069 LG manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Function 21 ADV. PICTURE Menu Options 1. Press the A.IRISbutton on the remote control. 2. Press the ,button to adjust the screen condition as you want. Auto Iris Function * This function adjusts the brightness of the entire image depending on inputted image to provide optimum image quality. Each press of the, button changes the screen as shown below. Manual: You can adjust from 0to 32on Advanced Control of ADV. PICTURE. You can use this function through the MENUbutton. To exit the menu display, press the EXITbutton. F FManualG G F FAuto Iris3G G F FAuto Iris1G G F FOffG GF FAuto Iris2G G 1. Press the MENUbutton. Then, move to ADV. PICTUREwith the ,,,buttons and press the OK button. 2. Move to a sub-item with the button. Then, use the ,buttons to move to TruMotion Demo and press the OK button. Press the MENUor EXITbutton to exit the menu screen. TruMotion Demo Function TruMotion onTruMotion off OKMoveADV. PICTURE TruMotion Demo Advanced Control Adv. Picture Reset
Function 22 G GColor Temp: Selects the mood of screen colors. G GGamma: Sets the intensity of the picture. G GReal Cinema: Set up the picture for the best picture appearance for viewing movies. G GBlack Level: Adjusting the contrast and the brightness of the screen using the black level of the screen. You can also use the C.TEMPbutton on the remote control. You can also use the GAMMAbutton on the remote control. You can use it only in Video, S-Video, Component(480i/576i/1080i 50/60Hz, 1080p 24Hz) and HDMI(1080i 50/60Hz, 1080p 24Hz) modes. You cannot set this function in SECAM, PAL 60 and PAL BGDK signals of Video, S-Videoand RGB modes. •Color Temp.F FMediumG GF FCoolG GOKF FG GF FNaturalG GF FWarmG G •GammaF FLowG GF FMediumG GOKF FG GF FHighG G •TruMotionF FHighG GF FOffG GOKF FG GF FLowG G G GTruMotion: Makes the moving image smoother through compensation. This function cannot be set when PC signal is input. G GNoise Reduction: Removes noise from image without damaging it. You can use it only in Video, S-Video, Component(480i, 480p, 576i, 576p) and HDMI(480p, 576p) modes. •Noise ReductionF FOnG GF FOffG GOKF FG G •Black LevelF FLowG GF FHighG GOKF FG G •Real CinemaF FOffG GF FOnG GOKF FG G 1. Press the MENUbutton. Then, move to ADV. PICTUREwith the ,,,buttons and press the OK button. 2. Move to a sub-item with the button. Then, use the ,buttons to move to Advanced Control and press the OK button. 3. Move to a desired item with the ,buttons and then press the OK button. 4. Use the ,buttons to make a desired adjustment and then press the OKbutton. You can set image values differently for each input and Picture Mode.Press the MENUor EXITbutton to exit the menu screen. Advanced Control Function OKMoveADV. PICTURE < When Picture Modeis Vivid/Standard/Sport/Game> < When Picture Modeis Cinema/Expert 1/2> TruMotion Demo Advanced Control Adv. Picture Reset OKMoveADV. PICTURE TruMotion Demo Expert Control Adv. Picture Reset F F Off G G 0 High Off Off High Low 100E Auto Iris •Manual •TruMotion •Noise Reduction •Real Cinema •Black Level •Lamp Mode •Overscan F F Off G G 0 Off Natural Off Low Off AutoE Auto Iris •Manual •TruMotion •Color Temp. •Noise Reduction •Gamma •Real Cinema •Black Level
Function 23 G GLamp Mode: Adjusts the lamp brightness. G GOverscan: You can adjust from 90, 92, 94...100. G GGamma Mode: You can select this mode only when Picture Modeis Cinema/Expert 1/2. G GWhite Balance: Adjusts the overall feeling of the screen to your choice. You can select this function only when Picture Modeis Cinema/Expert 1/2. Adjustment: You can select Low, Mediumor High. Level: You can adjust from 0to 8. IRE: Automatically set from 0to 100according to Levelchange. When you select User-> Red/Green/Blue : You can adjust from -127to 127. Red/Green/Blue Contrast: You can adjust from -30to 30. Red/Green/Blue Brightness: You can adjust from -30to 30. This function cannot be set when the signal is 1080i and 1080p or Aspect Ratiois set as Justscan.Noise can occur at the edges of the screen at the signal of 1080i/1080p because of the malfunctioning of an image input device. In this case, change the signal into the one that can be set with Overscanand set Overscan. OKMoveADV. PICTURE1. Press the MENUbutton. Then, move to ADV. PICTUREwith the ,,,buttons and press the OK button. 2. Move to a sub-item with the button. Then, use the ,buttons to move to Adv. Picture Reset and press the OKbutton. 3. Move to Ye swith the ,buttons and then press the OKbutton. Press the MENUor EXITbutton to exit the menu screen. Advanced Picture Reset Function TruMotion Demo Advanced Control Adv. Picture Reset * Settings of the selected ADV PICTUREfunction for each input and Picture Modereturn to the default factory settings. •Lamp ModeF FHighG GF FLowG GOKF FG G •Gamma ModeF FPresetG GF FUserG GOKF FG G •OverscanF F90G G~ ~F F100G GOKF FG G •White BalanceF FMediumG GF FCoolG GOKF FG GF FNaturalG GF FWarmG G •Red ContrastF F-30G GF F0G G~F F30G GOKF FG G
Function 24 SCREEN Menu Options 1. Press the MENUbutton. Then, move to SCREENwith the ,,, buttons and press the OK button. 2. Move to a sub-item with the button. Then, use the ,buttons to move to PJT Mode and press the OKbutton. 3. Move to a desired item with the ,buttons and then press the OK button. Select Rearwhen projecting from the back of the transparent screen purchased separately. Select Ceilingwhen installing the product on the ceiling.Press the MENUor EXITbutton to exit the menu screen. Some options may not be available depending on input signals. You can use this function through the MENUbutton. To exit the menu display, press the EXITbutton. To Change PJT Mode OKMoveSCREEN PJT Mode : Front Aspect Ratio : 16 : 9 Keystone Test Pattern RGB Config. Screen Reset * This function turns the projected image upside down or flips horizontal. 1. Press the RATIObutton on the remote control. 2. Use the , buttons to select a desired screen size. Using Aspect Ratio Function F FAutoG GF F4 : 3G G F FJust ScanG GF F16 : 9G G
Function 25 KeystoneMovePrev.MENU 1. Press the KEYSTONEbutton of remote control. 2. Move to a desired item with the ,buttons and then press the button. 3. Press the ,,,button to adjust the screen condition as you want and then press the OKbutton. Keystonecan be adjusted from -100 to 100.Execute Reset to restore back to default factory settings. You can use this function through the MENUbutton. To exit the menu display, press the EXITbutton. Using Keystone Function * Use this function when the screen is not at a right angle to the projector and the image is a trapezoid shape. * Only use the Keystonefunction when you can’t get the best angle of projection. Press the PATTERNbutton of remote control. You can use this function through the MENUbutton. To exit the menu display, press the EXITbutton. Test Pattern Function * Execute this function when installing the projector to adjust the screen size and focus. Top Right Bottom Left Top LeftG Bottom Right Reset H : 0 V : 0 1. Press the AUTO button of the remote controller.Image positioning and synchronization are automatically adjusted. 2. After automatic adjustments, if further manual adjustments are needed depending on PC RGB Config.on the SCREENmenu. In certain circumstances, you can’t get the best picture quality by only using auto-correction. Auto configure Function * This function assures you of getting the best video quality by automatically adjusting the horizontal size and synchronization of the image. * Auto Tracking function works in RGB PC input only. You can also use this function by using the MENUbutton. (Only in RGB mode) For best results, perform this function while displaying a still image. Auto configuration is on the process. Please wait a moment.Auto RGB Config.
Function 26 1. Press the MENUbutton. Then, move to SCREENwith the ,,,buttons and press the OK button. 2. Move to a sub-item with the button. Then, use the ,buttons to move to RGB Config. and press the OKbutton. 3. Move to a desired item with the ,buttons and then press the button. 4. Press the ,,,button to adjust the screen condition as you want and then press the OKbutton. The Auto Configurefunction operates only for RGB input. If you execute screen adjustment for a video from PC graphic signal, optimal state may not be found. Execute the Auto Configurefunction for a still image. The variable range can be different depends on input resolutions. To exit the menu display, press the EXITbutton. RGB Config. Function RGB Config. Phase Clock Auto ConfigureG Position OKMove Auto Configure? Ye sNo 1. Press the MENUbutton. Then, move to SCREENwith the ,,, buttons and press the OK button. 2. Move to a sub-item with the button. Then, use the ,buttons to move to Screen Reset and press the OKbutton. 3. Move to Ye swith the ,buttons and then press the OKbutton. Keystonefunction is not reset.Press the MENUor EXITbutton to exit the menu screen. Screen Reset Function * Settings of the selected SCREENmodes return to the default factory settings. OKMoveSCREEN PJT Mode : Front Aspect Ratio : 16 : 9 Keystone Test Pattern RGB Config. Screen Reset
Function 27 OKMoveOPTION Language : English Blank Image : Blue Sleep Time : Off Auto Sleep : Off Option Reset 1. Press the STILLbutton on the remote control. * You can freeze the moving image. 2. To exit STILL, press any button. * The STILL function will release automatically after approximately 10 minutes. Using Still Function OPTION Menu Options 1. Press the MENUbutton. Then, move to OPTIONwith the ,,, buttons and press the OK button. 2. Move to a sub-item with the button. Then, use the ,buttons to move to Language and press the OKbutton. 3. Move to a desired item with the ,buttons and then press the OK button. On-Screen-Display (OSD) is displayed in the selected language.Press the MENUor EXITbutton to exit the menu screen. Selecting Language 1. Press the BLANKbutton on the remote control. The screen turns off to a background color.You can choose the background color. (Refer to ‘Selecting Blank image color’) 2. Press any button to cancel the blank function.To temporarily turn off the lamp, press BLANK on the remote control. Do not block the projection lens with any objects when the projector is under operation as this could cause the objects to become heated and deformed or even cause a fire. Using Blank Function * This function may be effective if you need to get the attention of the audience during presentations, meetings or briefings.
Function 28 1. Press the MENUbutton. Then, move to OPTIONwith the ,,, buttons and press the OK button. 2. Move to a sub-item with the button. Then, use the ,buttons to move to Blank Image and press the OKbutton. 3. Move to a desired item with the ,buttons and then press the OK button. Background color will be altered to the selected Blank function color.Press the MENUor EXITbutton to exit the menu screen. Selecting Blank image color OKMoveOPTION Language : English Blank Image : Blue Sleep Time : Off Auto Sleep : Off Option Reset * The sleep timer turns the projector off at the preset time. 1. Press the SLEEPbutton of remote control. 2. Press the ,button to select the desired preset time. Each press of the , button changes the screen as shown below. You can use this function through the MENUbutton.To exit the menu display, press the EXITbutton. Sleep time Function F FOffG GF F10 MinG GF F20 MinG GF F30 MinG G F F240 MinG GF F180 MinG GF F120 MinG GF F90 MinG G F F60 MinG G
Function 29 1. Press the MENUbutton. Then, move to OPTIONwith the ,,, buttons and press the OK button. 2. Move to a sub-item with the button. Then, use the ,buttons to move to Auto Sleep and press the OKbutton. 3. Move to Onwith the ,buttons and then press the OKbutton. Press the MENUor EXITbutton to exit the menu screen. Auto sleep Function * This function turns the projector off automatically after 10 minutes is passed when there is no signal.OKMoveOPTION Language : English Blank Image : Blue Sleep Time : Off Auto Sleep : Off Option Reset INFORMATION Menu Options 1. Press the MENUbutton. Then, move to OPTIONwith the ,,, buttons and press the OK button. 2. Move to a sub-item with the button. Then, use the ,buttons to move to Option Reset and press the OKbutton. 3. Move to Ye swith the ,buttons and then press the OKbutton. Languagefunction is not reset.Press the MENUor EXITbutton to exit the menu screen. Option Reset Function * Settings of the selected OPTIONmodes return to the default factory settings. OKMoveOPTION Language : English Blank Image : Blue Sleep Time : Off Auto Sleep : Off Option Reset 1. Press the MENUbutton. Then, move to INFORMATIONwith the ,,,buttons and press the OK button. 2. You can see the current information of the projector. Press the MENUor EXITbutton to exit the menu screen. To See The Projector Information MoveINFORMATION Serial No. : CF181D-JS Lamp Time : 9 Hr Input : Video Resolution : NTSC M Fh/Fv : 15.7KHz/60.0Hz
Information 30 Supported Monitor Display Component-*1 HDMI(DTV)-*2 Signal * Cable type 1- Component Cable 2- HDMI Cable 60Hz480i 480p 720p 1080i 1080p 576i 576p 720p 1080i 1080p 1080p 50Hz 24/25/30HzO O O O O O O O O O OX O O O O X O O O O O * The following table lists the display formats supported by the projector. * If the projector does not support the input signal, “Out of Range” message appears on the screen. * The projector supports DDC1/2B type as Plug & Play function. (Auto recognition of PC monitor) * The Synchronization input form for horizontal and vertical frequencies are Separate. Format Vertical Freq.(Hz) Horizontal Freq.(kHz)