LG 55le5310 Owners Manual

							
A-37
PREPARATION
Only 32LE3***, 32/37/42LE4***, 32/37/42/47/55LE5***
 ■ Image shown may differ from your TV.
2345
7811910
1
Power Cord Socket
This TV operates on an AC power. The volt-age is indicated on the Specifications page. (► p.137 to 147) Never attempt to operate the TV on DC power.
HDMI/DVI IN Input
Connect an HDMI signal to HDMI IN. Or DVI (VIDEO) signal to HDMI/DVI port with DVI to HDMI cable.
OPTICAL DIGITAL AUDIO OUT 
Connect digital audio to various types of equipment. 
Connect to a Digital Audio Component.
Use an Optical audio cable. 
RGB/DVI Audio Input
Connect the audio from a PC or DTV. 
Euro Scart Socket (AV1) 
Connect scart socket input or output from an external device to these jacks. 
Component Input
Connect a component video/audio device to these jacks.
RGB IN Input
Connect the output from a PC. 
RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
This port is used for Service or Hotel mode. 
WIRELESS CONTROL
Connect the Wireless Media Box to the WIRELESS CONTROL jack on the TV. 
Audio/Video Input
 Connect audio/video output from an external device to these jacks.
Antenna Input
Connect antenna or cable to this jack.
USB Input 
Connect USB storage device to this jack.
PCMCIA (Personal Computer Memory Card International Association) Card Slot
Insert the CI Module to PCMCIA CARD SLOT.
(This feature is not available in all countries.)
Headphone Socket
Plug the headphone into the headphone socket.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
CAUTION
 ► Use a product with the following 
thickness for optimal connection to 
HDMI cable (Only HDMI IN 4) / 
USB device.
   *A    10 mm
6
12
13
14
2
10
   
						

							
A-38
PREPARATION
PREPARATION
Only 26/32LE3***, 32/42/47LE4***,
26LE5***, 32/37/42/47/55LE5***
Carefully place the TV screen side down 
on a cushioned surface to protect the 
screen from damage.
1
Assemble the TV as shown.3
Assemble the parts of the Stand Body with 
the Stand Base of the TV.2
Stand 
Body
Stand
Base
STAND INSTALLATION
Only 19/22LE3***, 22LE5***
 ■Image shown may differ from your TV.
When assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully, 
the product can tilt forward after the product installation.) If you tighten the bolt with excessive force, 
the bolt can deviate from abrasion of the tightening part of the bolt. 
Carefully place the TV screen side down 
on a cushioned surface to protect the 
screen from damage.
1
Assemble the TV as shown.
Fix the 4 bolts securely using the holes in 
the back of the TV.
3
4
Assemble the parts of the Stand Body with 
the Stand Base of the TV.2
Stand Body
Stand Base
M4 X 14
Assemble the parts of the Stand Rear 
Cover with the TV.4
Stand Rear 
Cover
Fix the 4 bolts securely using the holes in 
the back of the TV.5    
M4 X 14
(Only 26LE3***, 
26LE5***)
M4 X 16
(Only 32LE3***,
32/37/42LE4***, 
32/37/42/47/55LE5***)
M4 X 22(Only  32LE3***, 
32LE4***, 32LE5***)
M4 X 24(Only 37/42LE4***, 
37/42LE5***)
M4 X 26 (Only 47/55LE5***)
M4 X 20
(Only 26LE3***, 
26LE5***)
   
						

							
A-39
PREPARATION
BACK COVER FOR WIRE ARRANGEMENT
 ■Image shown may differ from your TV.
After connecting the cables as necessary, 
install Cable Holder as shown and bundle the 
cables.
Cable Holder
Only 19/22/26LE3***, 22/26LE5***
1
After connecting the cables as necessary, 
install Cable Holder as shown and bundle 
the cables.
Secure the power cord with the Cable 
Holder on the TV back cover.
It will help prevent the power cable from 
being removed by accident.
2
Cable Holder
Cable Holder
Only 32LE3***, 32/37/42LE4***, 
32/37/42/47/55LE5***
   
						

							
A-40
PREPARATION
PREPARATION
ATTACHING THE TV TO A 
DESK (Only 32LE3***, 32LE4***, 32LE5***)
Desk
Stand
 ■Ima4e shown may differ from your TV.
The TV must be attached to desk so it cannot be 
pulled in a forward/backward direction, potentially 
causing injury or damaging the product. Use only 
an attached screw.
  WARNING
 ►To prevent TV from falling over, the TV 
should be securely attached to the floor/wall 
per installation instructions. Tipping, shaking, 
or rocking the machine may cause injury.
1-Screw
 ( provided as parts of the product)
DESKTOP PEDESTAL 
INSTALLATION
10 cm
For adequate ventilation allow a clearance of 10 
cm all around the TV.
10 cm
10 cm10 cm
 ■Image shown may differ from your TV.
SWIVEL STAND
(Only 26/32LE3***, 32/37/42LE4***, 
26LE5***,  32/37/42/47/55LE5***)
 ■Image shown may differ from your TV.
After installing the TV, you can adjust the TV set 
manually to the left or right direction by 20 
degrees to suit your viewing position.
CONNECTION OF TV
(Only 19/22/26LE3***, 22/26LE5***)
 ■Image shown may differ from your TV.
1
2
3
Connect  the  antenna  cable  to  the  antenna 
input port on the TV.
Connect the DC adapter plug to the power 
input jack on the TV.
 Connect the power cord to the DC adapter 
first, then plug the power cord into the wall 
power outlet.
  CAUTION
 ►Please be sure to connect the TV to the DC 
power adapter before connecting the TV's power 
plug to a wall power outlet.
DC Adapter
   
						

							
A-41
PREPARATION
 ■This feature is not available for all models.
 ■Image shown may differ from your TV.
KENSINGTON SECURITY 
SYSTEM
2 
CAREFUL INSTALLATION 
ADVICE 
 ■You should purchase necessary components 
to fix the TV safety and secure to the wall on 
the market.
 ■  Position the TV close to the wall to avoid the 
possibility of it falling when pushed.
 ■  The instructions shown below are a safer way 
to set up the TV, by fixing it to the wall, avoid-
ing the possibility of it falling forwards if pulled. 
This will prevent the TV from falling forward 
and causing injury. This will also prevent the 
TV from damage. Ensure that children do not 
climb or hang from the TV.
3
Use the eye-bolts or TV brackets/bolts to fix 
the product to the wall as shown in the pic-
ture. 
(If  your  TV  has  bolts  in  the  eyebolts,  loosen 
then bolts.)
* Insert the eye-bolts or TV brackets/bolts and 
tighten them securely in the upper holes.
Secure the wall brackets with the bolts on 
the wall. Match the height of the bracket 
that is mounted on the wall.
Use a sturdy rope to tie the product for 
alignment. It is safer to tie the rope so it 
becomes horizontal between the wall and 
the product.
2 
11
 The TV is equipped with a Kensington Security 
System connector on the back panel. Connect 
the Kensington Security System cable as shown 
below.
For the detailed installation and use of the 
Kensington Security System, refer to the user’s 
guide provided with the Kensington Security 
System.
For further information, contact http://www.kens-
ington.com, the internet homepage of the 
Kensington 
company. Kensington sells security systems for 
expensive electronic equipment such as note-
book PCs and LCD projectors.
1
2
3
NOTE
 ►When moving the TV undo the cords first.
 ►Use a platform or cabinet strong and large 
enough to support the size and weight of the 
TV.
 ►To use the TV safely make sure that the 
height of the bracket on the wall and on the 
TV is the same.
NOTE
 ►The Kensington Security System is an 
optional accessory.
 ►If the TV feels cold to the touch, there may 
be a small “flicker” when it is turned on.                
This is normal, there is nothing wrong with 
TV.
 ►Some minute dot defects may be visible on 
the screen, appearing as tiny red, green, or 
blue spots. However, they have no adverse 
effect on the monitor's performance.
 ►Avoid touching the LCD screen or holding 
your finger(s) against it for long periods of 
time. Doing so may produce some temporary 
distortion effects on the screen.
2 
   
						

							
A-42
PREPARATION
PREPARATION
 ■The TV can be installed in various ways such as 
on a wall, or on a desktop etc.
 ■The TV is designed to be mounted horizontally.
Power Supply
Circuit breaker
EARTHING
Ensure that you connect the earth wire to prevent 
possible electric shock. If grounding methods are 
not possible, have a qualified electrician install a 
separate circuit breaker. 
Do not try to earth the TV by connecting it to tele-
phone wires, lightening rods or gas pipes.
WALL MOUNT: HORIZONTAL 
INSTALLATION
 ■We recommend the use of a LG Brand wall 
mounting bracket when mounting the TV to a wall.
 ■We recommend that you purchase a wall mount-
ing bracket which supports VESA standard.
 ■LG recommends that wall mounting be per-
formed by a qualified professional installer.
10 cm
10 cm
10 cm
10 cm
10 cm
NOTE
 ►Should Install wall mount on a solid wall per-
pendicular to the floor.
 ►Should use a special wall mount, if you want 
to install it to ceiling or slanted wall.
 ►The surface that wall mount is to be mount-
ed on should be of sufficient strength to sup-
port the weight of TV set; e.g. concrete, nat-
ural rock, brick and hollow block.
 ►Installing screw type and length depends on 
the wall mount used. Further information, 
refer to the instructions included with the 
mount.
 ►LG is not liable for any accidents or damage 
to property or TV due to incorrect installa-
tion:
 - Where a non-compliant VESA wall mount 
is used.
 - Incorrect fastening of screws to surface 
which may cause TV to fall and cause per-
sonal injury.
 - Not following the recommended Installation 
method.
Place  the  ring  spacers  on  the  set  before 
installing  the  wall  mounting  bracket  so  that 
the inclination of the  backside of the set can 
be adjusted perpendicularly.
< Only 26LE3***, 26LE5*** >
4-Ring spacers
 ■Image shown may differ from your TV.
ModelVESA(A * B)
Standard ScrewQuantity
19/22/26LE3***
32LE3***
32LE4***
37/42LE4***
22/26LE5***
32LE5***
37/42/47LE5***
55LE5***
100 * 100
200 * 100
200 * 100
200 * 200
100 * 100
200 * 100
200 * 200
400 * 400
M4
M4
M4
M6
M4
M4
M6
M6
4
4
4
4
4
4
4
4
   
						

							
A-43
PREPARATION
REMOTE CONTROL KEY FUNCTIONS 
When using the remote control, aim it at the remote control sensor on the TV.
 ■Image shown may differ from your TV.
(POWER)
ENERGY SAVING
AV MODE
INPUT
TV/RAD
Switches the TV on from standby or off to standby.
Adjust the Energy Saving mode of the TV.(► p.95)
It helps you select and set images and sounds when connecting AV devices.(► p.50)
External input mode rotate in regular sequence.(► 
p.43)
Selects Radio, TV and DTV channel.
0 to 9 number button
LIST
Q.VIEW
Selects a programme.
Selects numbered items in a menu.
Displays the programme table. (► p.41)
Returns to the previously viewed programme.
Coloured 
buttons
These buttons are used for teletext (on TELETEXT 
models only), Programme edit.
TELETEXT BUTTONS
SUBTITLE
These buttons are used for teletext.
For further details, see the ‘Teletext’ section.(► p.130)
Recalls your preferred subtitle in digital mode.
1
MENU
GUIDE  
Q. MENU
BACK
EXIT
 INFO  i
THUMBSTICK
(Up/Down/Left/Right)
OK
Selects a menu.Clears  all  on-screen  displays  and  returns  to  TV viewing from any menu.(► p.19)
Shows programme guide.(► p.86)
Select the desired quick menu source. (Aspect Ratio, Clear Voice II , Picture Mode, Sound Mode, Audio (or Audio Language), Sleep Timer, Skip Off/On, USB Device).(► p.18)
Allows the user to move return one step in an inter-active  application,  EPG  or  other  user  interaction function. Clears  all  on-screen  displays  and  returns  to  TV viewing from any menu.
Shows the present screen information.
 Allows you to navigate the on-screen menus and adjust the system settings to your preference.
Accepts your selection or displays the current mode.
1
1
   
						

							
A-44
PREPARATION
PREPARATION
VOLUME UP
/DOWN
FAV
MARK
RATIO
MUTE
Programme
UP/DOWN
PAGE UP/DOWN
Adjusts the volume. 
Displays the selected favourite programme.
Select the input to apply the Picture Wizard 
settings.
Check and un-check programmes in the USB menu.
Selects your desired Aspect Ratio of picture.
(► p.92)
Switches the sound on or off.
Selects a programme.
Move from one full set of screen information to the next one.
Installing Batteries
 ■Open the battery compartment cover on the back and install 
the batteries matching correct polarity (+with +,-with -). 
 ■Install two 1.5 V AAA batteries. Do not mix old or used batter-
ies with new ones.
 ■Close cover.
 ■To remove the batteries, perform the installation actions in 
reverse.
SIMPLINK / 
MY MEDIA Menu   
control buttons
Controls SIMPLINK or MY MEDIA menu(Photo List and Music List or Movie List).
AD
See a list of AV devices connected to TV.
When you toggle this button, the Simplink menu appears at the screen.(► p.46)
Switches the Audio Description On or Off.
2
2
2
   
						

							
1
EXTERNAL  EQUIPMENT  SETUP
EXTERNAL EQUIPMENT SETUP
ANTENNA CONNECTION
 ■For optimum picture quality, adjust antenna direction.
 ■ An antenna cable and converter are not supplied.
 ■To prevent damage do not connect to the mains outlet until all connections are made between the 
devices.
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Outdoor 
Antenna
(VHF, UHF)
Wall 
Antenna 
Socket
RF Coaxial Wire (75 Ω)
Antenna
UHF
Signal
Amplifier
VHF
 ■In poor signal areas, to achieve better picture quality it may be necessary to install a signal amplifier 
to the antenna as shown above.
 ■If signal needs to be split for two TVs,use an antenna signal splitter for connection.
   
						

							
2
EXTERNAL EQUIPMENT SETUP
EXTERNAL  EQUIPMENT  SETUP
CONNECTING WITH A COMPONENT CABLE
 ■To avoid damaging any equipment, never plug in any power cord until you have finished connecting all equipment.
 ■This section on EXTERNAL EQUIPMENT SETUP mainly uses diagrams for the 32/37/42/47LD4*** models.
 ■Image shown may differ from your TV.
This TV can receive Digital RF/Cable signals without an external digital set-top box. However, if you do 
receive Digital signals from a digital set-top box or other digital external device, refer to the diagram as 
shown below.
 ►HDMI Audio Supported format :  Dolby Digital, PCM
 DTS Audio format is not supported. 
Component Input ports
To achieve better picture quality, connect a DVD player to the component input ports as shown below.
SignalComponentHDMI
480i/576iOX
480p/576pOO
720p/1080iOO
1080pO 
(50 Hz / 60 Hz only)
O(24 Hz / 30 Hz / 50 Hz / 60 Hz)
 Component ports on the TVYPBPR
Video output ports 
on DVD player
YPBPR
YB-YR-Y
YCbCr
YPbPr
1Connect the video outputs (Y, PB, PR) of the 
external equipment (digital set-top box, DVD, 
etc.) to the COMPONENT IN VIDEO jacks on 
the TV. 
2Connect the audio output of the external equip-
ment (digital set-top box, DVD, etc.) to the 
COMPONENT IN AUDIO jacks on the TV.
3Turn on the external equipment. 
(Refer to the external equipment's manual for 
operating instructions.)
4Select the Component input source using the 
INPUT button on the remote control.
    
1
2
1
2
or