LG 32le5900 Owners Manual

A-57
PREPARATION
1
11
0 to 9 number button
(Space)
LIST
Q.VIEW Selects a programme.
Selects numbered items in a menu.
Opens an empty space on the screen keyboard.
Displays the programme table. (► p.55)
Returns to the previously viewed programme.
]
TELETEXT 
BUTTONS
SUBTITLE These buttons are used for teletext.
For further details, see the ‘T
eletext’ section.
( ►
 p.177)
Recalls your preferred subtitle in digital mode.
See a list of AV devices connected to TV.
When you toggle this button, the Simplink...

A-58
PREPARATION
PREPARATION
Installing Batteries
 
■ Open the battery compartment cover on the back and install 
the batteries matching correct polarity (+with +,-with -). 
 
■ Install two 1.5 V AAA batteries. Do not mix old or used batter-
ies with new ones.
 
■ Close cover

.
 
■ To remove the batteries, perform the installation actions in 
reverse.
SIMPLINK / 
MY MEDIA  Menu    
control buttons Controls SIMPLINK or MY MEDIA menu (Photo List, 
Music List and Movie List).
VOLUME UP
/DOWN
MARK
FAV...

A-59
PREPARATIONSimple Remote Control (Only 50/60PK9***, 50/60PX9
***)
 (
POWER)
TV/INPUT
VOLUME UP /DOWN
MUTE
Programme UP/DOWN Switches the TV on from standby or off to standby.
External input mode rotate in regular sequence.
(► p.57)
Adjusts the volume. 
Switches the sound on or off.
Selects a programme.
0 to 9 number 
button
OK
Q.VIEW Selects a programme.
Selects numbered items in a menu.
Accepts your selection or displays the current 
mode.
Returns to the previously viewed programme.
Installing...

1
EXTERNAL EQUIPMENT SETUP
EXTERNAL EQUIPMENT SETUP
ANTENNA CONNECTION
 
■ For optimum picture quality, adjust antenna direction.
 
■  
An antenna cable and converter are not supplied.
 
■ To prevent damage do not connect to the mains outlet until all connection\
s are made between the 
devices.
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Outdoor 
Antenna
(VHF, UHF) Wall 
Antenna 
Socket
RF Coaxial Wire (75...

2
EXTERNAL EQUIPMENT SETUP
EXTERNAL EQUIPMENT SETUP
CONNECTING WITH A COMPONENT CABLE
 
■ To avoid damaging any equipment, never plug in any power cord until you h\
ave finished connecting 
all equipment.
 
■ This section on EXTERNAL EQUIPMENT SETUP  mainly uses diagrams for the 32/37/42/47/55LE7
*** 
models.
 
■ Image shown may differ from your TV.
This TV  can receive Digital RF/Cable signals without an external digital set-top\
 box. However, if you do 
receive Digital signals from a digital set-top...

3
EXTERNAL EQUIPMENT SETUP
CONNECTING WITH AN HDMI CABLE
NOTE
 
► The TV can receive video and audio signals simultaneously 
when using an HDMI cable.
 
► If the DVD does not support Auto HDMI, you must set the 
output resolution appropriately.
 
► Check that your HDMI cable is High Speed HDMI Cable. If 
the HDMI cables are not High Speed HDMI Cable, flickering 
or no screen display can result. Please use the High Speed 
HDMI Cable.
1Connect the HDMI output of the external equipment (digital set-
top...

4
EXTERNAL EQUIPMENT SETUP
EXTERNAL EQUIPMENT SETUP
CONNECTING WITH AN HDMI TO DVI CABLE
1Connect the digital set-top box or the DVI out-
put of the PC to HDMI/DVI IN 1(DVI) jack on 
the TV.
2Connect the audio output of the digital set-top 
box or the PC audio output to the AUDIO IN 
(RGB/DVI)  jack on the TV.
3Turn on the digital set-top box or the PC and 
the TV. 
(
Refer to the digital set-top box or the PC 
manual for operating instructions.)
4Select HDMI1  input source using the  INPUT 
button on...

5
EXTERNAL EQUIPMENT SETUP
CONNECTING WITH A EURO SCART CABLE
ScartInput
Output
Video Audio RGB Video, Audio
AV 1
OOOAnalogue TV, Digital TV
NOTE
 
►  
Any Euro scart cable used must be signal shielded.
 
► When watching digital 
TV in 3D imaging mode, monitor out signals cannot be output through the \
SCART cable.  (Only 42/47LX6
***, 47/55LX9
***, 50/60PX9
***)
 
►  If you set the 3D mode to On while a scheduled recording is performed on\
 digital TV, monitor out 
signals cannot be output through the...

6
EXTERNAL EQUIPMENT SETUP
EXTERNAL EQUIPMENT SETUP
USB SETUP
1Connect the USB device to the  USB IN 1 or 
USB IN 2  jack on the 
 TV.
2After connecting the USB IN 1 or USB IN 2 
jack, you use the USB  function. (
►  p.90) 
    
CONNECTING WITH AN RF CABLE
To avoid picture noise (interference), allow adequate distance between \
the VCR and TV.
1Connect the ANT OUT socket of the VCR to 
the  ANTENNA IN socket on the  TV.
2  Connect the antenna cable to the  ANT IN 
socket of the VCR.
3Press the PLAY...