LG 26ld335 Owners Manual

							
A-17
PREPARATION
BACK PANEL INFORMATION
 
■  Image shown may differ from your TV.
Power Cord Socket
  This TV operates on an AC power. The volt-
age is indicated on the Specifications page. 
(►  p.137 to 147) Never attempt to operate 
the TV on DC power.
HDMI/DVI IN Input
    Connect an HDMI signal to HDMI IN. Or DVI 
(VIDEO) signal to HDMI/DVI port with DVI to 
HDMI cable.
OPTICAL DIGITAL AUDIO OUT 
  Connect digital audio to various types of 
equipment. 
Connect to a Digital Audio Component.
Use an Optical audio cable. 
RGB/DVI Audio Input
  Connect the audio from a PC or DTV. 
Euro Scart Socket (AV1) 
    Connect scart socket input or output from an 
external device to these jacks. 
  Component Input
Connect a component video/audio device to 
these jacks. RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
This port is used for Service or Hotel mode. 
RGB IN Input
  Connect the output from a PC.
Antenna Input
Connect antenna or cable to this jack.
USB Input 
Connect USB storage device to this jack.
PCMCIA (Personal Computer Memory 
Card International Association) Card Slot
Insert the CI Module to 
PCMCIA CARD 
SLOT .
(This feature is not available in all countries.)
Headphone Socket
   Plug the headphone into the headphone 
socket.
   Audio/Video Input
  Connect audio/video output from an external 
device to these jacks.
1
2
3
4
5
6
7
8
9
10
11
12
13
1
1
23456
798
10
11
2
12
13
 
						

							
A-18
PREPARATION
PREPARATION
STAND INSTALLATION
 
■ Image shown may differ from your TV
When assembling the desk type stand, check whether the bolt is fully tig\
htened. (If not tightened fully, 
the product can tilt forward after the product installation.) If you ti\
ghten the bolt with excessive force, 
the bolt can deviate from abrasion of the tightening part of the bolt. 
Carefully place the TV screen side down 
on a cushioned surface to protect the 
screen from damage.1
Assemble the TV as shown.
Fix the 4 bolts securely using the holes in 
the back of the TV.3
4
Assemble the parts of the  Stand Body with 
the  Cover Base  of the TV.2
Stand Body
Cover Base
Only 32/37/42/47LD45 **
Carefully place the TV screen side down 
on a cushioned surface to protect the 
screen from damage.1
Assemble the TV as shown.
Fix the 4 bolts securely using the holes in 
the back of the TV.2
3
Only 32/37/42/47LD42 **,
 
26/32LD32 **,
 26/32LD33
**
 
						

							
A-19
PREPARATION
BACK COVER FOR 
WIRE ARRANGEMENT
 
■ Image shown may differ from your TV.
NOTE
 
► Do not use the  Cable Management Clip  to lift 
the TV.
-   If the TV is dropped, you may be injured or the 
TV may be damaged.
Connect the cables as 
necessary.
To connect additional 
equipment, see the 
EXTERNAL EQUIPMENT 
SETUP section.1
  Open the  Cable Management Clip  as 
shown.2
Cable Management Clip
Fit the  Cable Management Clip  as shown.3
 
■ Image shown may differ from your TV.
When installing the wall-mounted unit, 
use the protection cover. 
NOT USING THE 
DESK-TYPE STAND 
Insert the  Protection 
Cover  into the TV until 
clicking sound.
Protection Cover
ATTACHING THE TV TO A 
DESK
 
(Only 32/37/42LD4 ***, 26/32LD32
**, 
26/32LD33 **)
Desk
Stand
 
■ Image shown may differ from your TV.
The TV must be attached to desk so it cannot 
be pulled in a forward/backward direction, 
potentially causing injury or damaging the 
product. Use only an attached screw.
  WARNING
 
► To prevent TV from falling over, the TV 
should be securely attached to the floor/wall 
per installation instructions. Tipping, shaking, 
or rocking the machine may cause injury.
1-Screw
 ( provided as parts of the product)
 
						

							
A-20
PREPARATION
PREPARATION
 
■ This feature is not available for all models.
 
■ Image shown may differ from your TV.
KENSINGTON SECURITY 
SYSTEM
2 
CAREFUL INSTALLATION 
ADVICE 
 
■ You should purchase necessary components 
to fix the TV safety and secure to the wall on 
the market.
 
■    Position the TV close to the wall to avoid the 
possibility of it falling when pushed.
 
■    The instructions shown below are a safer way 
to set up the TV, by fixing it to the wall, avoid-
ing the possibility of it falling forwards if pulled. 
This will prevent the TV from falling forward 
and causing injury. This will also prevent the 
TV from damage. Ensure that children do not 
climb or hang from the TV.
3
Use the eye-bolts or TV brackets/bolts to fix the 
product to the wall as shown in the picture. 
(If your TV has bolts in the eyebolts, loosen 
then bolts.)
* Insert the eye-bolts or TV brackets/bolts and 
tighten them securely in the upper holes.
Secure the wall brackets with the bolts on 
the wall. Match the height of the bracket 
that is mounted on the wall.
Use a sturdy rope to tie the product for align-
ment. It is safer to tie the rope so it becomes 
horizontal between the wall and the product.
2 
1
1
  The TV is equipped with a Kensington Security 
System connector on the back panel. Connect 
the Kensington Security System cable as shown 
below.
For the detailed installation and use of the 
Kensington Security System, refer to the user’s 
guide provided with the Kensington Security 
System.
For further information, contact http://www.kens-
ington.com, the internet homepage of the 
Kensington 
company. Kensington sells security systems for 
expensive electronic equipment such as note-
book PCs and LCD projectors.
1
2
3
NOTE
 
► When moving the TV undo the cords first.
 
► Use a platform or cabinet strong and large 
enough to support the size and weight of the 
TV.
 
► To use the TV safely make sure that the 
height of the bracket on the wall and on the 
TV is the same.
NOTE
 
► The Kensington Security System is an 
optional accessory.
 
► If the TV feels cold to the touch, there may 
be  a  small  “flicker”  when  it  is  turned  on.                
This is normal, there is nothing wrong with 
TV.
 
► Some minute dot defects may be visible on 
the screen, appearing as tiny red, green, or 
blue spots. However, they have no adverse 
effect on the monitors performance.
 
► Avoid touching the LCD screen or holding 
your finger(s) against it for long periods of 
time. Doing so may produce some temporary 
distortion effects on the screen.
2 
10 cm
 
						

							
A-21
PREPARATION
 
■ The TV can be installed in various ways such as 
on a wall, or on a desktop etc.
 
■ The TV is designed to be mounted horizontally.
Power Supply
Circuit breaker
EARTHING
Ensure that you connect the earth wire to 
prevent possible electric shock. If grounding 
methods are not possible, have a qualified 
electrician install a separate circuit breaker. 
Do not try to earth the TV by connecting it to 
telephone wires, lightening rods or gas pipes.
DESKTOP PEDESTAL 
INSTALLATION
WALL MOUNT: HORIZONTAL 
INSTALLATION
 
■ We recommend the use of a LG Brand wall 
mounting bracket when mounting the TV to a 
wall.
 
■ We recommend that you purchase a wall 
mounting bracket which supports VESA stan-
dard.
 
■ LG recommends that wall mounting be per-
formed by a qualified professional installer.
10 cm
10 cm 10 cm10 cm
For adequate ventilation allow a clearance of 10 
cm all around the TV.
Model
VESA
(A  * B) Standard 
Screw Quantity
32LD4
***
37/42/47LD4 ***
26/32LD32 **
26/32LD33 **200 
* 100
200  * 200
200  * 100
200  * 100 M4
M6
M4
M4 4
4
4
4
10 cm
10 cm
10 cm
10 cm
10 cm
NOTE
 
► Should Install wall mount on a solid wall per-
pendicular to the floor.
 
► Should use a special wall mount, if you want to 
install it to ceiling or slanted wall.
 
► The surface that wall mount is to be mounted 
on should be of sufficient strength to support 
the weight of TV set; e.g. concrete, natural 
rock, brick and hollow block.
 
► Installing screw type and length depends on 
the wall mount used. Further 
information, refer 
to the instructions included with the mount.
 
► LG is not liable for any accidents or damage to 
property or TV due to incorrect installation:
  - Where a non-compliant VESA wall mount is  used.
  - Incorrect fastening of screws to surface  which may cause TV to fall and cause per-
sonal injury.
  - Not following the recommended Installation  method.
 
■ Image shown may differ from your TV.
SWIVEL STAND 
 
■ Image shown may differ from your TV.
After installing the TV, you can adjust the TV set 
manually to the left or right direction by 20 
degrees to suit your viewing position.
 
						

							
A-22
PREPARATION
PREPARATION
REMOTE CONTROL KEY FUNCTIONS 
When using the remote control, aim it at the remote control sensor on th\
e TV.
(POWER)
ENERGY SAVING
AV MODE
INPUT
TV/RAD
Switches the TV on from standby or off to standby.
Adjust the Energy Saving mode of the TV.(
► p.95)
It helps you select and set images and sounds 
when connecting AV devices.(
► p.50)
External input mode rotate in regular sequence.
(► 
p.43)
Selects Radio, TV and DTV channel.
0 to 9 number  button
LIST
Q.VIEWSelects a programme.
Selects numbered items in a menu.
Displays the programme table. 
(► p.41)
Returns to the previously viewed programme.
Coloured  buttonsThese buttons are used for teletext (on  TELETEXT 
models only),  Programme edit .
TELETEXT 
BUTTONS
SUBTITLEThese buttons are used for teletext.
For further details, see the ‘Teletext’ section.(
► p.130)
Recalls your preferred subtitle in digital mode.
1
MENU
GUIDE   
Q. MENU
BACKEXIT
 INFO  i
THUMBSTICK
(Up/Down/Left/Right)
OK
Selects a menu.
Clears all on-screen displays and returns to TV 
viewing from any menu.
(► p.19)
Shows programme guide.(► p.86)
Select the desired quick menu source. (Aspect 
Ratio, Clear Voice II , Picture Mode, Sound Mode, 
Audio (or Audio Language), Sleep Timer, Skip Off/
On, USB Device).(
► p.18)
Allows the user to move return one step in an inter-
active application, EPG or other user interaction 
function.
 
Clears all on-screen displays and returns to TV 
viewing from any menu.
Shows the present screen information.
  Allows you to navigate the on-screen menus and 
adjust the system settings to your preference.
Accepts your selection or displays the current 
mode.
1
 
						

							
A-23
PREPARATION
VOLUME UP/DOWN
FAV
MARK
RATIO MUTE
Programme UP/DOWN
PAGE UP/ DOWNAdjusts the volume. 
Displays the selected favourite programme.
Select the input to apply the Picture Wizard 
settings.
Check and un-check programmes in the USB 
menu.
Selects your desired Aspect Ratio of picture.
(
► p.92)
Switches the sound on or off.
Selects a programme.
Move from one full set of screen information to the 
next one.
Installing Batteries
 
■ Open the battery compartment cover on the back and install 
the batteries matching correct polarity (+with +,-with -). 
 
■ Install two 1.5 V AAA batteries. Do not mix old or used batter-
ies with new ones.
 
■ Close cover.
 
■ To remove the batteries, perform the installation actions in 
reverse.
SIMPLINK / 
MY MEDIA Menu   
control buttons
Controls SIMPLINK or MY MEDIA menu(Photo List 
and Music List).
See a list of AV devices connected to TV.
When you toggle this button, the Simplink menu 
appears at the screen.(
► p.46)
 
						

							
A-24
PREPARATION
PREPARATION
Use of ferrite core (This feature is not available for all models.)
Ferrite core can be used to reduce the electromagnetic 
wave when connecting the power cord.
The closer the location of the ferrite core to the power 
plug, the better it is.
Install the power plug closely.
ACCESSORIES LCD TV MODELS : 
32/42/46/52/60LD5***
Ensure that the following accessories are included with your TV. If an accessory is missing, please 
contact the dealer where you purchased the TV.
 
■ Image shown may differ from your TV.
Owner’s Manual Ferrite Core
(
This item is not included  for all models.)Power Cord
Polishing Cloth
Polishing cloth for 
use on the screen.
This item is not included for all models.
* Lightly wipe any 
stains or fingerprints 
on the surface of the 
TV with the polishing 
cloth.
Do not use exces-
sive force. This may 
cause scratching or 
discolouration.      
1-screw for stand fixing (Only 32/42LD5 ***)Protection 
CoverBolts for stand assembly
x 8
M4 x 20
Batteries
(AAA) Remote Control
 
						

							
A-25
PREPARATION
FRONT PANEL CONTROLS
NOTE
 
► TV can be placed in standby mode in order to reduce the power consumptio\
n. And TV should be 
switched off using the power switch on the TV if it will not be watched for some time, as this will 
reduce energy consumption.
 
 
► The energy consumed during use can be significantly reduced if the level\
 of brightness of the picture 
is reduced, and this will reduce the overall running cost.
 
 CAUTION
 
► Do not step on the glass stand or subject it to any impact. It may break\
, causing possible injury from frag-
ments of glass, or the TV may fall.
 
► Do not drag the TV. The floor or the product may be damaged.
 
■ Image shown may differ from your TV.
PROGRAMME
VOLUME
OK
MENU
INPUT
POWER
Power/Standby Indicator
• Illuminates red in standby mode.
• Illuminates blue when the TV is 
switched on.
Intelligent Sensor
Adjusts picture according to 
the surrounding conditions.
Remote Control Sensor
SPEAKER
 
						

							
A-26
PREPARATION
PREPARATION
BACK PANEL INFORMATION
 
■ Image shown may differ from your TV.
Power Cord Socket
This TV operates on an AC power. The volt-
age is indicated on the Specifications page. 
(
► p.137 to 147) Never attempt to operate 
the TV on DC power.
HDMI/DVI IN Input
Connect an HDMI signal to HDMI IN. Or DVI 
(VIDEO) signal to HDMI/DVI port with DVI to 
HDMI cable.
RGB IN Input
Connect the output from a PC.
OPTICAL DIGITAL AUDIO OUT 
Connect digital audio to various types of 
equipment. 
Connect to a Digital Audio Component.
Use an Optical audio cable. 
RGB/DVI Audio Input
Connect the audio from a PC or DTV. 
Euro Scart Socket (AV1) 
  Connect scart socket input or output from an 
external device to these jacks. 
Component Input
Connect a component video/audio device to 
these jacks.
RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
This port is used for Service or Hotel mode. 
WIRELESS Control
Connect the Wireless Media Box to the 
WIRELESS CONTROL  jack on the TV. 
Antenna Input
Connect antenna or cable to this jack.
USB Input 
Connect USB storage device to this jack.
PCMCIA (Personal Computer Memory 
Card International Association) Card Slot
Insert the CI Module to  PCMCIA CARD 
SLOT .
(This feature is not available in all countries.)
Headphone Socket
Plug the headphone into the headphone 
socket.
Audio/Video Input
Connect audio/video output from an external 
device to these jacks.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1
236457
98
11
2
12
13
14
10