LG 23mp65hqp User Manual

							21
ENGENGLISH
CUSTOMIZING SETTINGS
 
NOTE
 yWhen monitor goes to power saving mode with pc saving option-> Pressing \
any button -> OSD 
appear and user should press dual button -> User can bring back to norma\
l mode.
DUAL DISPLAY
1   Press FUNC. button on the bottom of the Monitor set 
to display the FUNC. OSD. 
2 Select DUAL DISPLAY by pressing the ► button. 
3 Enter to DUAL DISPLAY by pressing the ▼ button.
4 Set the options by pressing the ◄ or ► buttons.
5 Select EXIT to   leave the OSD menu.To return to the 
upper menu or set other menu items, use  the up 
arrow () button.
* Before using below functions, please install DUAL SMART SOLUTION programme.
Each option is explained below.
DUAL DISPLAYDescription
CloneBy selecting Clone,user can use secondary monitor as done mode of primar\
y monitor.
ExtendedBy selecting Extended,user can use secondary monitor as extended mode of\
 primary monitor.
OffIf select Off,DUAL DISPLAY is off.
DUAL WEB
1   Press FUNC. button on the bottom of the Monitor set 
to display the FUNC. OSD. 
2 Select DUAL WEB by pressing the ► button. 
3 Enter to DUAL WEB by pressing the ▼ button.
4 Set the options by pressing the ◄ or ► buttons.
5 Select EXIT to   leave the OSD menu.To return to the 
upper menu or set other menu items, use  the up 
arrow () button.
* Before using below functions, please install DUAL SMART SOLUTION programme.
Each option is explained below.
DUAL WEBDescription
OnHelp user to browse web efficiently by dividing in half. Help to arrange and move windowson screen. Help user to control dividedwindows ratio. 
OffIf select Off,DUAL WEB is off.  
						

							22
ENGENGLISH
TROUBLESHOOTING
TROUBLESHOOTING
Check the following before calling for service.
No image appears
Is the power cord of the display connected? yCheck and see if the power cord is connected properly to the power 
outlet.
Is the power indicator light on? yPress the Power button.
Is the power on and the power indicator White? yAdjust the brightness and the contrast.
Is the power indicator flickering? yIf the display is in power saving mode, try moving the mouse or 
pressing any key on the keyboard to bring up the screen.
 yTry to turn on the PC.
Do you see an "OUT OF RANGE" message on the screen? yThis message appears when the signal from the PC (video card) is 
out of horizontal or vertical frequency range of the display. See the 
'Specifications' section of this manual and configure your display 
again.
Do you see a "NO SIGNAL" message on the screen?  yWhen the monitor is on "No-Signal" in 5 minutes, the monitor goes to 
DPM mode.
Do you see a "OSD LOCKED" message on the screen?
Do you see “OSD LOCKED” when you push MENU button? yYou can secure the current control settings, so that they cannot be 
inadvertently changed. You can unlock the OSD controls at any time 
by pushing the MENU button for several seconds: the message “OSD 
UNLOCKED” will appear.
Display image is incorrect
Display Position is incorrect. yPress the AUTO button to automatically adjust your display image to 
the ideal setting.
On the screen background, verticalbars or stripes are visible. yPress the AUTO button to automatically adjust your display image to 
the ideal setting. 
Any horizontal noise appearing in any image or characters are not clearly portrayed.
 yPress the AUTO button to automatically adjust your display image to 
the ideal setting. 
 yCheck Control Panel ► Display ► Settings and adjust the display 
to the recommended resolution or adjust the display image to the ideal 
setting. Set the color setting higher than 24 bits  (true color).  
						

							23
ENGENGLISH
TROUBLESHOOTING
Display image is incorrect
The screen color is mono or abnormal. yCheck if the signal cable is properly connected and use a screwdriver 
to fasten if necessary.
 yMake sure the video card is properly inserted in the slot.
 ySet the color setting higher than 24 bits (true color) at Control Panel 
► Settings.
The screen blinks. yCheck if the screen is set to interlace mode and if yes, change it to the 
recommend resolution.
Do you see an "Unrecognized monitor, Plug&Play (VESA DDC) monitor found" message?
Have you installed the display driver? yBe sure to install the display driver from the display driver CD (or 
diskette) that comes with your display. Or, you can also download the 
driver from our web site: http://www.lg.com.
 yMake sure to check if the video card supports Plug&Play function.
  yCheck Control Panel ► Display ► Settings and see if the frequency or the resolution were 
changed.  If yes, readjust the video card to the recommend resolution.
 yIf the recommended resolution (optimal resolution) is not selected, le\
tters may be blurred and the 
screen may be dimmed, truncated or biased. Make sure to select the recom\
mend resolution.
 yThe setting method can differ by computer and O/S (Operation System), and resolution mentioned 
above may not be supported by the video card performance. In this case, \
please ask to the computer 
or the video card manufacturer.
CAUTION
The screen is flickering.
Did you select the recommended resolution? yIf the selected resolution is HDMI 1080i 60/50 Hz, the screen may 
be flickering. Change the resolution to the recommended resolution 
1080P.  
						

							24
ENGENGLISH
SPECIFICATIONS
SPECIFICATIONS  
DisplayScreen Type54.6 cm (21.5 inch) Flat Panel Active matrix-TFT LCDAnti-Glare coatingVisible diagonal size: 54.6 cm
Pixel Pitch0.2745 mm x 0.2745 mm (Pixel Pitch)
Sync InputHorizontal Frequency30 kHz to 83 kHz (Automatic)
Vertical Frequency56Hz to 75Hz (D-SUB)56Hz to 61Hz (HDMI)
Input FormSeparate Sync. Digital
Video InputSignal Input15 pin D-SUB Connector HDMI Connector
Input FormRGB Analog (0.7 Vp-p/ 75 ohm), Digital
ResolutionMaxD-SUB(Analog) : 1920 x 1080 @ 60  HzHDMI (Digital) : 1920 x 1080 @ 60 Hz
RecommendVESA 1920 x 1080 @ 60 Hz
Plug & PlayDDC 2B(Analog,HDMI)
Power ConsumptionOn Mode : 20 W(ENERGY STAR® standard)*Sleep Mode ≤ 0.3 W Off Mode ≤ 0.3 W 
Power Input19 V  1.3 A
AC-DC AdapterType ADS-40SG-19-3 19025G, manufactured by SHENZHEN HONOR ELECTRONICor Type ADS-40FSG-19 19025GPG-1, manufactured by SHENZHEN HONOR ELECTRONICor Type ADS-40FSG-19 19025GPBR-1, manufactured by SHENZHEN HONOR ELECTRONICor Type ADS-40FSG-19 19025GPI-1, manufactured by SHENZHEN HONOR ELECTRONICor Type ADS-40FSG-19 19025GPCU-1, manufactured by SHENZHEN HONOR ELECTRONICor Type ADS-40FSG-19 19025GPB-2, manufactured by SHENZHEN HONOR ELECTRONICor Type LCAP21, manufactured by LIEN CHANG ELECTRONIC ENTERPRISEor Type LCAP26-A, manufactured by LIEN CHANG ELECTRONIC ENTERPRISEor Type LCAP26-E, manufactured by LIEN CHANG ELECTRONIC ENTERPRISEor Type LCAP26-I, manufactured by LIEN CHANG ELECTRONIC ENTERPRISEor Type LCAP26-B, manufactured by LIEN CHANG ELECTRONIC ENTERPRISEor Type PSAB-L203A, manufactured by LG Innotek Co.,Ltdor Type PSAB-L202B, manufactured by LG Innotek Co.,Ltdor Type PSAB-L202C, manufactured by LG Innotek Co.,Ltdor Type PSAB-L202D, manufactured by LG Innotek Co.,Ltd
OUTPUT: 19 V  1.3 A
Dimensions(Width x Height x Depth)
With Stand50,0 cm x 38,0 cm x 17,8 cm
Without Stand50,0 cm x 30,7 cm x 6,9 cm
Weight2.7 kg
Tilt Range-5° to 20°
EnvironmentalconditionsOperating TemperatureOperating Humidity10°C to 35 °C10 % to 80 % 
Storage TemperatureStorage Humidity-20°C to 60 °C   5 % to 90 % non-Condensing
Stand BaseAttached (    ), Detached (O)
Power cordWall-outlet type
Product specifications shown above may be changed without prior notice d\
ue to upgrade of product 
functions.* The power consumption level can be different by operating condition and monitor setting.* The On mode power consumption is measured with ENERGY STAR® test standard. * ENERGY STAR® is a US registered mark of the United States Environmental Protec\
tion Agency.
22MP65HQ  
						

							25
ENGENGLISH
SPECIFICATIONS
SPECIFICATIONS  
DisplayScreen Type58.4 cm (23 inch) Flat Panel Active matrix-TFT LCDAnti-Glare coatingVisible diagonal size: 58.4 cm
Pixel Pitch0.265 mm x 0.265 mm (Pixel Pitch)
Sync InputHorizontal Frequency30 kHz to 83 kHz (Automatic)
Vertical Frequency56Hz to 75Hz (D-SUB)56Hz to 61Hz (HDMI)
Input FormSeparate Sync. Digital
Video InputSignal Input15 pin D-SUB ConnectorHDMI Connector 
Input FormRGB Analog (0.7 Vp-p/ 75 ohm), Digital
ResolutionMaxD-SUB(Analog) : 1920 x 1080 @ 60 HzHDMI (Digital) : 1920 x 1080 @ 60 Hz
RecommendVESA 1920 x 1080 @ 60 Hz
Plug & PlayDDC 2B(Analog,HDMI)
Power ConsumptionOn Mode : 21 W(ENERGY STAR® standard)*Sleep Mode ≤ 0.3 W Off Mode ≤ 0.3 W 
Power Input19 V  1.6 A
AC-DC AdapterType ADS-40SG-19-3 19032G, manufactured by SHENZHEN HONOR ELECTRONICor Type ADS-40FSG-19 19032GPG-1, manufactured by SHENZHEN HONOR ELECTRONICor Type ADS-40FSG-19 19032GPBR-1, manufactured by SHENZHEN HONOR ELECTRONICor Type ADS-40FSG-19 19032GPI-1, manufactured by SHENZHEN HONOR ELECTRONICor Type ADS-40FSG-19 19032GPCU-1, manufactured by SHENZHEN HONOR ELECTRONICor Type LCAP21A, manufactured by LIEN CHANG ELECTRONIC ENTERPRISEor Type LCAP26A-A, manufactured by LIEN CHANG ELECTRONIC ENTERPRISEor Type LCAP26A-E, manufactured by LIEN CHANG ELECTRONIC ENTERPRISEor Type LCAP26A-I, manufactured by LIEN CHANG ELECTRONIC ENTERPRISEor Type LCAP26A-B, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE
OUTPUT: 19 V  1.7 A
Dimensions(Width x Height x Depth)
With Stand53.3 cm x 42.6 cm x 18.8 cm
Without Stand53.3 cm x 32.6 cm x 6.9 cm
Weight3.0 kg
Tilt Range-5° to 20°
EnvironmentalconditionsOperating TemperatureOperating Humidity10°C to 35 °C10 % to 80 % 
Storage TemperatureStorage Humidity-20°C to 60 °C   5 % to 90 % non-Condensing
Stand BaseAttached (    ), Detached (O)
Power cordWall-outlet type
Product specifications shown above may be changed without prior notice d\
ue to upgrade of product functions.* The power consumption level can be different by operating condition and monitor setting.* The On mode power consumption is measured with ENERGY STAR® test standard. * ENERGY STAR® is a US registered mark of the United States Environmental Protec\
tion Agency.
23MP65HQ  
						

							26
ENGENGLISH
SPECIFICATIONS
SPECIFICATIONS  
DisplayScreen Type68.6 cm (27 inch) Flat Panel Active matrix-TFT LCDAnti-Glare coatingVisible diagonal size: 68.6 cm
Pixel Pitch0.3114 mm x 0.3114 mm (Pixel Pitch)
Sync InputHorizontal Frequency30 kHz to 83 kHz (Automatic)
Vertical Frequency56Hz to 75Hz (D-SUB)56Hz to 61Hz (HDMI)
Input FormSeparate Sync. Digital
Video InputSignal Input15 pin D-SUB ConnectorHDMI Connector 
Input FormRGB Analog (0.7 Vp-p/ 75 ohm), Digital
ResolutionMaxD-SUB(Analog) : 1920 x 1080 @ 60  HzHDMI (Digital) : 1920 x 1080 @ 60 Hz
RecommendVESA 1920 x 1080 @ 60 Hz
Plug & PlayDDC 2B(Analog,HDMI)
Power ConsumptionOn Mode : 26 W(ENERGY STAR® standard)*Sleep Mode ≤ 0.3 W Off Mode ≤ 0.3 W 
Power Input19 V  1.6 A
AC-DC AdapterType ADS-40SG-19-3 19032G, manufactured by SHENZHEN HONOR ELECTRONICor Type ADS-40FSG-19 19032GPG-1, manufactured by SHENZHEN HONOR ELECTRONICor Type ADS-40FSG-19 19032GPBR-1, manufactured by SHENZHEN HONOR ELECTRONICor Type ADS-40FSG-19 19032GPI-1, manufactured by SHENZHEN HONOR ELECTRONICor Type ADS-40FSG-19 19032GPCU-1, manufactured by SHENZHEN HONOR ELECTRONICor Type LCAP21A, manufactured by LIEN CHANG ELECTRONIC ENTERPRISEor Type LCAP26A-A, manufactured by LIEN CHANG ELECTRONIC ENTERPRISEor Type LCAP26A-E, manufactured by LIEN CHANG ELECTRONIC ENTERPRISEor Type LCAP26A-I, manufactured by LIEN CHANG ELECTRONIC ENTERPRISEor Type LCAP26A-B, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE
OUTPUT: 19 V  1.7 A
Dimensions(Width x Height x Depth)
With Stand62.3 cm x 47.6 cm x 21.3 cm
Without Stand62.3 cm x 36.9 cm x 10.6 cm
Weight4.6 kg
Tilt Range-5° to 20°
EnvironmentalconditionsOperating TemperatureOperating Humidity10°C to 35 °C10 % to 80 % 
Storage TemperatureStorage Humidity-20°C to 60 °C   5 % to 90 % non-Condensing
Stand BaseAttached (    ), Detached (O)
Power cordWall-outlet type
Product specifications shown above may be changed without prior notice d\
ue to upgrade of product functions.* The power consumption level can be different by operating condition and monitor setting.* The On mode power consumption is measured with ENERGY STAR® test standard. * ENERGY STAR® is a US registered mark of the United States Environmental Protec\
tion Agency.
27MP65HQ  
						

							27
ENGENGLISH
SPECIFICATIONS
Preset Modes (Resolution)
Display Modes (Resolution)Horizontal Frequency(kHz)Vertical Frequency(Hz)Polarity(H/V)
720 x 40031.46870-/+
640 x 48031.46960-/-
640 x 48037.50075-/-
800 x 60037.87960+/+
800 x 60046.87575+/+
1024 x 76848.36360-/-
1024 x 76860.02375+/+
1152 x 86467.50075+/+
1280 x 102463.98160+/+
1280 x 102479.97675+/+
1680 x 105065.29060-/+
1920 x 108067.50060+/+Recommend Mode
HDMI Timing
Factory support mode(Preset Mode)Horizontal Frequency(kHz)Vertical Frequency(Hz)HDMI
480P31.5060O
576P31.2550O
720P37.5050O
720P45.0060O
1080i28.1250O
1080i33.7560O
1080P56.2550O
1080P67.5060ORecommend Mode
Indicator
ModeLED Color
On ModeWhite
Sleep ModeBlinking White
Off ModeOff  
						

							28
ENGENGLISH
PROPER POSTURE
Proper posture for using the Monitor set.
PROPER POSTURE
Adjust the 
Monitor set and 
your posture to 
allow you to view 
images at the 
optimal viewing 
angle.
Place your hands 
gently on the 
keyboard, keeping 
your arms bent at 
the elbows and 
horizontally outright.
Adjust the location of the 
Monitor set to avoid it 
reflecting light.  
						

							Make sure to read the Safety Precautions before  
using the product.
Keep the Owner’s Manual (CD) in an accessible 
place for future reference.
The model and serial number of the SET is 
located on the back and one side of the SET. 
Record it below should you ever need service.As an ENERGY STAR Partner LGE 
U. S. A.,Inc. has determined that this 
product meets the ENERGY STAR 
guidelines for energy efficiency.
ENERGY STAR is a set of power-saving
guidelines issued by the U.S.Environmental
Protection Agency(EPA).
MODEL
SERIAL
*above information is only for USA FCC Regulatory
Declaration of Conformity
Trade Name: LG
Model : 22MP65HA
            23MP65HA
            27MP65HA
Responsible Party: LG Electronics Inc.
Address : 1000 Sylvan Ave. Englewood Cliffs    
                NJ 07632 U.S.A
TEL: 201-266-2534