LG 22m35ab User Manual

							www.lg.com
19M35A
20M35A
22M35A
24M35A
19M35D
20M35D
22M35D
24M35D
LED LCD MONITOR MODEL
ENGLISH
OWNER\fS MANUAL
LED LCD MONITOR
\flea\be read thi\b manual carefully before operating 
your \bet and retain it for future reference. 
						

							2
ENGENGLISH
TABLE OF CONTENTS
CONTENTS
3	 ASSEMBLING	AND	PREPAR-
ING
3	 Unpacking
4	 Parts	and	buttons
5	 Setting	up	the	Monitor	set	
5	 -	 Attaching	the	Stand	Base
5	 -	 Detaching	the	Stand	Base	
6	 -	 Mounting	on	a	table
6	 -	 Using	the	cable	holder
8	 -	 Mounting	on	a	wall
9	 USING	THE	MONITOR	SET
9	 Connecting	to	a	PC
9	 -	 D-SUB	connection
9	 -	 DVI-D	connection
11	 CUSTOMIZING	SETTINGS
12	 Customizing	Settings
12	 -	 Menu	Settings
13			-	Picture
14			-	Color
15			-	Display
16			-	Others
17	 READER	Setting
18	 FUNC.	Setting
18			-	SUPER	ENERGY 	SAVING	
19			-	Picture	Mode
20			-	DUAL	DISPLAY
20	 		-	DUAL	WEB
21	 TROUBLESHOOTING
23		
SPECIFICATIONS	
23	 19M35A
24	 19M35D
25	 20M35A
27	 20M35D
29	 22M35A
30	 22M35D
31	 24M35A
32	 24M35D
33	 Preset	Modes	(Resolution)
34	 Indicator
35	 PROPER	POSTURE
35	 Proper	posture	for	using	the	Monitor	set.  
						

							3
ENGENGLISH
ASSEMBLING AND P\fEPA\fING
ASSEMBLING	AND	PREPARING
Unpacking
Check	your	product	box	for	the	following	items.	If	there	are	any	missing	accessories,	contact	the	local	
dealer	where	you	purchased	 your	product. 	The	 illustrations	 in	this	 manual	 may	differ	 from	the	actual	 product	
and	accessories.
yyDo	not	use	any	unapproved	accessories	to	ensure	the	safety	and	product	life	span.
yyAny	damages	or	injuries	by	using	unapproved	accessories	are	not	covered	by	the	warranty.	
yyThe	accessories	supplied	with	your	product	may	vary	depending	on	the	model.
yyProduct 	specifications 	or 	contents 	in 	this 	manual 	may 	be 	changed 	without 	prior 	notice 	due 	to 	upgrade	
of	product	functions.
CAUTION
NOTE
Stand	BodyStand	Base
CD(Owner's	Manual)	/
	Card
D-SUB	Cable
(	Depending	on	the	country	)(	Depending	on	the	country	)
Power	CordAC-DC	 AdapterAC-DC	Adapter
or	
DVI-D	Cable
(This	cable	is	not	included	in	all	
countries.)
(19M35D,20M35D,22M35D,24M35D)  
						

							4
ENGENGLISH
ASSEMBLING AND P\fEPA\fING
Parts	and	buttons
Power	Indicator
yyLighting	On: 	Turned 	on
yyLighting 	Off: 	Turned 	off
Connection	panel	(See	p.9)
Button	(See	p.11)
(Power	Button)  
						

							5
ENGENGLISH
ASSEMBLING AND P\fEPA\fING
Attach	the	Stand	Body	to	the	monitor	set.
Attach	the	Stand	Base.
Tighten	the	screw	to	the	right.
Setting	up	the	Monitor	set	
Attaching	the	Stand	Base
1	 Place	the	Monitor	set	with	the	screen	side	
down	on	a	flat	and	cushioned	surface.
Lay	a	foam	mat	or	soft	protective	cloth	
on	the	surface	to	protect	the	screen	from	
damage.
CAUTION
2	
Stand	Base
Stand	Body
1
2
3
Detaching	the 	Stand 	Base 	
1	 Place	the	Monitor	set	with	the	screen	side	
down	on	a	flat	and	cushioned	surface.
Stand	Base
Stand	Base
Stand	Body
Stand	Body
Pull	out	the	Stand	Body	and	Stand	Base	
from	the	monitor	set.
Turn	the	screw	to	the	left.
Pull	out	the	Stand	Base.
1
2
3
2	  
						

							6
ENGENGLISH
ASSEMBLING AND P\fEPA\fING
Mounting	on	a	table
1	 Lift	and	tilt	the	Monitor	set	into	its	upright	
position	on	a	table.
Leave	a	10	cm	(minimum)	space	from	the	wall	
for	proper	ventilation.
Using	the	cable	holder
2	 Connect	the	AC-DC	Adapter	and	Power	Cord	
to	a	wall	outlet.
3	 Press	(Power)	button	on	the	bottom	switch	
panel	to	turn	the	power	on.
\b0 cm
\b0 cm
\b0 cm
\b0 cm
Unplug	the	power	cord	before	moving	the	
Monitor	to	another	location.	Otherwise	electric	
shock	may	occur.
CAUTION
Cable	holder
or	  
						

							7
ENGENGLISH
ASSEMBLING AND P\fEPA\fING
Using	the	Kensington	security	system	
The	Kensington	security	system	connector	is	
located	at	the	back	of	the	Monitor	set.	For	more	
information	of	installation	and	using,	refer	to	the	
manual	supplied	with	the	Kensington	security	
system	or	visit	http://www.kensington.com.
Connect	the	Kensington	security	system	cable	
between	the	Monitor	set	and	a	table.
The	Kensington	security	system	is	optional.	
You	can	obtain	it	from	most	electronics	stores.
NOTE
When	you	adjust	the	angle,	do	not	hold	the	
bottom	of	the	Monitor	set	frame	as	shown	on	
the	following	illustration,	as	may	injure	your	
fingers.
Do	not	touch	or	press	the	screen	when	
adjusting	the	angle	of	the	monitor.
Do	not	hold	this	set	like	below	picture.Monitor	
screen	can	detach	from	stand	base	and	injure	
your	body.
WARNING
Tilt	from 	+20 	to 	-3 	degrees 	up 	or 	down 	to 	adjust	
the	angle	of	the	Monitor	set	to	suit	your	view.
NOTE
FrontRear  
						

							8
ENGENGLISH
ASSEMBLING AND P\fEPA\fING
Mounting	on	a	wall
For	proper	ventilation,	allow	a	clearance	of	10	cm	
on	each	side	and	from	the	wall.	Detailed	
instructions	are	available	from	your	dealer,	see	the		
optional	Tilt	Wall	Mounting	Bracket	Installation	and
Setup	Guide.
If	you	intend	to	mount	the	Monitor	set	to	a	wall,	
attach	Wall	mounting	interface	(optional	parts)	to	
the	back	of	the	set.
When	you	install	the	Monitor	set	using	a	wall	
mounting	interface	(optional	parts),	attach	it	
carefully	so	it	will	not	drop.
1		Please,	Use	the	screw	and	wall	mount	interface	
in	accordance	with	VESA 	Standards.
2		If	you	use	screw	longer	than	standard,	the	
monitor	might	be	damaged	internally.	
3		If	you	use	improper	screw,	the	product	might	be	
damaged	and	drop	from	mounted	position.		In	
this	case,	LG	Electronics	is	not	responsible	for	
it.	
4		VESA	compatible.
5		Please	use	VESA 	standard	as	below.
yy784.8	mm	(30.9	inch)	and	under
*	Wall	Mount	Pad	Thickness	:	2.6	mm
*	Screw	:	Φ	4.0	mm	x	Pitch	0.7	mm	x	
																Length	10	mm
yy787.4	mm	(31.0	inch)	and	above
*	Please	use	VESA 	standard	wall	mount	pad	
and	screws.
\b0 cm
\b0 cm
\b0 cm\b0 cm
yyDisconnect	the	power	cord	first,	and	then	
move	or	install	the	Monitor	set.	Otherwise	
electric	shock	may	occur.
yyIf	you	install	the	Monitor	set	on	a	ceiling	or	
slanted	wall,	it	may	fall	and	result	in	severe	
injury.	
yyUse	only	an	authorized	LG	wall	mount	
and	contact	the	local	dealer	or	qualified	
personnel.
yy	Do	not	over	tighten	the	screws	as	this	may	
cause	damage	to	the	Monitor	set	and	void	
your	warranty.	
yy	Use	only	screws	and	wall	mounts	that	
meet	the	VESA	standard.	Any	damages	
or	injuries	by	misuse	or	using	an	improper	
accessory	are	not	covered	by	the	warranty.
yyUse	the	screws	that	are	listed	on	the	VESA 	
standard	screw	specifications.
yyThe	wall	mount	kit	will	include	an	installation	
manual	and	necessary	parts.
yyThe	wall	mount	bracket	is	optional.	You	can	
obtain	additional	accessories	from	your	local	
dealer.
yyThe	length	of	screws	may	differ	depending	
on	the	wall	mount.	Be	sure	to	use	the	proper	
length.
yyFor	more	information,	refer	to	the	
instructions	supplied	with	the	wall	mount.
CAUTION
NOTE
Model\b9M35A  \b9M35D
20M35A  20M35D
22M35A  22M35D
	
24M35A
24M35D
	
VESA 	(A	x	B)75		x	75100		x	100
Standard	screwM4M4
Number	of	screws44  
						

							9
ENGENGLISH
USING THE MONITO\f SET
USING	THE	MONITOR	SET
Connecting	to	a	PC
yyYour	Monitor	set	supports	Plug	&	Play*.	
*Plug	&	Play:		A	PC	recognizes	a	connected	
device	that	users	connect	to	a	PC	and	turn	
on,	without	device	configuration	or	user	
intervention.
D-SUB	connection
Transmits	analog	video	from	your	PC	to	the	
Monitor	set.	Connect	the	PC	and	the	Monitor	set	
with	the	supplied	D-sub	15	pin	signal	cable	as	
shown	in	the	following	illustrations.
yyMac	adapter
For	 Apple	Macintosh	use,	a	separate	plug	
adapter	is	needed	to	change	the	15	pin	
high	density	(3	row)	D-SUB	VGA 	connector	
on	the	supplied	cable	to	a	15	pin	2	row	
connector.
yyWhen	using	a	D-Sub	signal	input	cable	
connector	for	Macintosh
NOTE
DVI-D	connection
Transmits	a	digital	video	signal	from	your	PC	to	
the	Monitor	set.	Connect	the	PC	and	the	Monitor	
set	with	a	DVI	cable	as	shown	in	the	following	
illustrations.  
						

							\b0
ENGENGLISH
USING THE MONITO\f SET
yyWhen	you	want	to	use	two	PC	in	our	Monitor,	
please	connect	the	signal	cable(D-SUB/
DVI-D)	respectively	in	Monitor	set.
yyIf	you	turn	the	Monitor	set	on	while	it	is	cold,	
the	screen	may	flicker.	This		is	normal.
yySome	red,	green,	or	blue	spots	may	appear	
on	the	screen.	This	is	normal.
yy"Self	Image	Setting"	Function.
This	function	provides	the	user	with	optimal	
display	settings.When	the	user	connects	
the	monitor	for	the	first	time,	this	function	
automatically	adjusts	the	display	to	optimal	
settings	for	individual	input	signals.(Only	
supported	in	Analog	Mode)
yy‘AUTO’	Function.
When	you	encounter	problems	such	as	
blurry	screen,	blurred	letters,	screen	flicker	
or	tilted	screen	while	using	the	device	or	
after	changing	screen	resolution,	press	the	
AUTO	function	button	to	improve	resolution.
(Only	supported	in	 Analog	Mode)
NOTENOTE
Self	Image	Setting	Function
Press	the	power	button	on	the	bottom	panel	to	
turn	the	power	on.	When	monitor	power	is	turned	
on,	the	"Self	Image	Setting"	Function	is	executed	
automatically.	(Only	supported	in	 Analog	Mode)
yyConnect	the	signal	
input	cable	and	tighten	
it	by	turning	the	screws	
clockwise.
yyDo	not	press	the	screen	with	your	finger	for		
a	long	time	as	this	may	result	in	temporary	
distortion	on	the	screen.
yyAvoid	displaying	a	fixed	image	on	the	
screen	for	a	long	period	of	time	to	prevent	
image	burn.	Use	a	screensaver	if	possible.
CAUTION