LG 22ld355 Owners Manual

							
A-7
PREPARATION
 
■ Image shown may differ from your TV.
When installing the wall-mounted unit, use the protection cover. 
NOT USING THE DESK-TYPE STAND 
Carefully place the TV screen side down 
on a cushioned surface to protect the 
screen from damage.1
Only 19/22LD35 **, 19/22LD34
**
Loose the bolts from TV.2
Detach the stand from TV.3
Insert the Protection Cover  into the TV.
After removing the protection paper from 
the protection cover, adhere it to the TV as 
shown.4
Protection Cover
Insert the  Protection Cover  into the TV until 
clicking sound.
Only 26/32LD35 **, 26/32LD34
**
Protection Cover
 
						

							
A-8
PREPARATION
PREPARATIONConnect the cables as necessary.
To connect additional equipment, see the 
External Equipment Setup section.1
Open the Cable Management Clip  as 
shown.2
Fit the  Cable Management Clip  as shown.3
Only 26/32LD35
**, 26/32LD34
**
Cable Management Clip
BACK COVER FOR WIRE ARRANGEMENT
 
■ Image shown may differ from your TV.
NOTE
 
► Do not use the  Cable Management Clip  to lift 
the TV.
-   If the TV is dropped, you may be injured or the 
TV may be damaged.
Only 19/22LD35
**, 19/22LD34
**
After connecting the cables as necessary, install 
Cable Holder  as shown and bundle the cables.
Cable Holder
 
						

							
A-9
PREPARATION
SWIVEL STAND
(Except for 19/22LD35**,
  19/22LD34
**)
 
■ Image shown may differ from your TV.
After installing the TV, you can adjust the TV set 
manually to the left or right direction by 20 
degrees to suit your viewing position.
POSITIONING YOUR DISPLAY 
(Only 19/22LD35 **, 19/22LD34
**)
 
■ Image shown may differ from your TV.
 
■ Adjust the position of the panel in various ways 
for maximum comfort.
• Tilt range
ATTACHING THE TV TO A 
DESK
 (Only 26/32LD35 **, 26/32LD34
**)
Desk
Stand
 
■  Image shown may differ from your TV.
The TV must be attached to desk so it cannot be 
pulled in a forward/backward direction, potentially 
causing injury or damaging the product. Use only 
an attached screw.
  WARNING
 
► To prevent TV from falling over, the TV 
should be securely attached to the floor/wall 
per installation instructions. Tipping, shaking, 
or rocking the machine may cause injury.
1-Screw  (  provided as parts of the product)
 
						

							
A-10
PREPARATION
PREPARATION
 
■ This feature is not available for all models.
 
■ Image shown may differ from your TV.
KENSINGTON SECURITY 
SYSTEM
2 
CAREFUL INSTALLATION 
ADVICE 
 
■ You should purchase necessary components 
to fix the TV safety and secure to the wall on 
the market.
 
■    Position the TV close to the wall to avoid the 
possibility of it falling when pushed.
 
■    The instructions shown below are a safer way 
to set up the TV, by fixing it to the wall, avoid-
ing the possibility of it falling forwards if pulled. 
This will prevent the TV from falling forward 
and causing injury. This will also prevent the 
TV from damage. Ensure that children do not 
climb or hang from the TV.
3
Use the eye-bolts or TV brackets/bolts to fix the 
product to the wall as shown in the picture. 
(If your TV has bolts in the eyebolts, loosen 
then bolts.)
* Insert the eye-bolts or TV brackets/bolts and 
tighten them securely in the upper holes.
Secure the wall brackets with the bolts on the 
wall. Match the height of the bracket that is 
mounted on the wall.
Use a sturdy rope to tie the product for align-
ment. It is safer to tie the rope so it becomes 
horizontal between the wall and the product.
2  2 
1
1
  The TV is equipped with a Kensington Security 
System connector on the back panel. Connect 
the Kensington Security System cable as shown 
below.
For the detailed installation and use of the 
Kensington Security System, refer to the user’s 
guide provided with the Kensington Security 
System.
For further information, contact http://www.kens-
ington.com, the internet homepage of the 
Kensington 
company. Kensington sells security systems for 
expensive electronic equipment such as note-
book PCs and LCD projectors.
1
2
3
NOTE
 
► When moving the TV undo the cords first.
 
► Use a platform or cabinet strong and large 
enough to support the size and weight of the TV.
 
► To use the TV safely make sure that the height of 
the bracket on the wall and on the TV is the 
same.
NOTE
 
► The Kensington Security System is an optional 
accessory.
 
► If the TV feels cold to the touch, there may be a 
small “flicker” when it is turned on.                
This is normal, there is nothing wrong with TV.
 
► Some minute dot defects may be visible on the 
screen, appearing as tiny red, green, or blue 
spots. However, they have no adverse effect on 
the monitors performance.
 
► Avoid touching the LCD screen or holding your 
finger(s) against it for long periods of time. 
Doing so may produce some temporary distor-
tion effects on the screen.
 
						

							
A-11
PREPARATION
 
■ The TV can be installed in various ways such as 
on a wall, or on a desktop etc.
 
■ The TV is designed to be mounted horizontally.
Power 
Supply
Circuit 
breaker
EARTHING
Ensure that you connect the earth wire to prevent 
possible electric shock. If grounding methods are 
not possible, have a qualified electrician install a 
separate circuit breaker. 
Do not try to earth the TV by connecting it to tele-
phone wires, lightening rods or gas pipes.
WALL MOUNT: HORIZONTAL 
INSTALLATION
 
■ We recommend the use of a LG Brand wall 
mounting bracket when mounting the TV to a 
wall.
 
■ We recommend that you purchase a wall mount-
ing bracket which supports VESA standard.
 
■ LG recommends that wall mounting be per-
formed by a qualified professional installer.
DESKTOP PEDESTAL 
INSTALLATION
Model VESA
(A  * B) Standard 
Screw Quantity
19/22LD35
**
26/32LD35 **
19/22LD34 **
26/32LD34 **100 
* 100
200  * 100
100  * 100
200  * 100 M4
M4
M4
M4 4
4
4
4
10 cm
10 cm
10 cm
10 cm
10 cm
NOTE
 
► Should Install wall mount on a solid wall per-
pendicular to the floor.
 
► Should use a special wall mount, if you want 
to install it to ceiling or slanted wall.
 
► The surface that wall mount is to be mount-
ed on should be of sufficient strength to sup-
port the weight of TV set; e.g. concrete, nat-
ural rock, brick and hollow block.
 
► Installing screw type and length depends on 
the wall mount used. Further information, 
refer to the instructions included with the 
mount.
 
► LG is not liable for any accidents or damage 
to property or TV due to incorrect installa-
tion:
 - Where a non-compliant VESA wall mount  is used.
 - Incorrect fastening of screws to surface  which may cause TV to fall and cause per-
sonal injury.
 - Not following the recommended Installation  method.
10 cm
For adequate ventilation allow a clearance of 10 
cm all around the TV.
10 cm
10 cm 10 cm
 
■ Image shown may differ from your TV.
 
						

							
A-12
PREPARATION
PREPARATION
REMOTE CONTROL KEY FUNCTIONS 
When using the remote control, aim it at the remote control sensor on th\
e TV.
(POWER)
ENERGY SAVING
AV MODE
INPUT
TV/RAD
Switches the TV on from standby or off to standby.
Adjust the Energy Saving mode of the TV.(
► p.95)
It helps you select and set images and sounds 
when connecting AV devices.(
► p.50)
External input mode rotate in regular sequence.
(► 
p.43)
Selects Radio, TV and DTV channel.
0 to 9 number  button
LIST
Q.VIEWSelects a programme.
Selects numbered items in a menu.
Displays the programme table. 
(► p.41)
Returns to the previously viewed programme.
MENU
GUIDE   
Q. MENU
BACKEXIT
 INFO  i
THUMBSTICK
(Up/Down/Left/Right)
OK
Selects a menu.
Clears all on-screen displays and returns to TV 
viewing from any menu.
(► p.19)
Shows programme guide.(► p.86)
Select the desired quick menu source. (Aspect 
Ratio, Clear Voice II , Picture Mode, Sound Mode, 
Audio (or Audio Language), Sleep Timer, Skip Off/
On, USB Device).(
► p.18)
Allows the user to move return one step in an inter-
active application, EPG or other user interaction 
function.
 
Clears all on-screen displays and returns to TV 
viewing from any menu.
Shows the present screen information.
  Allows you to navigate the on-screen menus and 
adjust the system settings to your preference.
Accepts your selection or displays the current 
mode.
Coloured  buttonsThese buttons are used for teletext (on  TELETEXT 
models only),  Programme edit .
TELETEXT 
BUTTONS
SUBTITLEThese buttons are used for teletext.
For further details, see the ‘Teletext’ section.(
► 
p.130)
Recalls your preferred subtitle in digital mode.
1
1
 
						

							
A-13
PREPARATION
VOLUME UP/DOWN
FAV
MARK
RATIO MUTE
Programme UP/DOWN
PAGE UP/ DOWNAdjusts the volume. 
Displays the selected favourite programme.
Select the input to apply the Picture Wizard 
settings.
Check and un-check programmes in the USB 
menu.
Selects your desired Aspect Ratio of picture.
(
► p.92)
Switches the sound on or off.
Selects a programme.
Move from one full set of screen information to the 
next one.
Installing Batteries
 
■ Open the battery compartment cover on the back and install 
the batteries matching correct polarity (+with +,-with -). 
 
■ Install two 1.5 V AAA batteries. Do not mix old or used batter-
ies with new ones.
 
■ Close cover.
 
■ To remove the batteries, perform the installation actions in 
reverse.
SIMPLINK / 
MY MEDIA Menu   
control buttons
Controls SIMPLINK or MY MEDIA menu(Photo List 
and Music List).
See a list of AV devices connected to TV.
When you toggle this button, the Simplink menu 
appears at the screen.(
► p.46)
 
						

							
A-14
PREPARATION
PREPARATION
ACCESSORIES LCD TV MODELS : 32/37/42/47LD4***, 26/32LD32
**, 
26/32LD33 **
Ensure that the following accessories are included with your TV. If an accessory is missing, please 
contact the dealer where you purchased the TV.
 
■  Image shown may differ from your TV.
Owner’s Manual Batteries 
(AAA) Remote Control
Power Cord
Polishing Cloth
Polishing cloth for 
use on the screen. This item is not included for all models.
* Lightly wipe any stains or 
fingerprints on the surface 
of the TV with the polish-
ing cloth.
Do not use excessive 
force. This may cause 
scratching or discoloura-
tion.      
Ferrite Core
(
This item is not included  for all models.)
Use of ferrite core (This feature is not available for all models.)
Ferrite core can be used to reduce the electromagnetic 
wave when connecting the power cord.
The closer the location of the ferrite core to the power 
plug, the better it is.
Install the power plug closely.
Bolts for stand assembly 1-screw for stand fixing
(Only 32/37/42LD4 ***, 
26/32LD32 **, 
26/32LD33 **)
x 8
(M4x20)
(Only 32/37/
42/47LD45 **)Protection 
Cover
x 4
(M4x24)
(Only 32/37/
42/47LD42 **, 
26/32LD32 **, 
26/32LD33 **)
or
 
						

							
A-15
PREPARATION
FRONT PANEL CONTROLS
 
■ Image shown may differ from your TV.
NOTE
 
► TV can be placed in standby mode in order to reduce the power consumptio\
n. And TV should be 
switched off using the power switch on the TV if it will not be watched for some time, as this will 
reduce energy consumption.
 
► The energy consumed during use can be significantly reduced if the level\
 of brightness of the 
picture is reduced, and this will reduce the overall running cost.
 
 CAUTION
 
► Do not step on the glass stand or subject it to any impact. It may break\
, causing possible injury 
from fragments of glass, or the TV may fall.
 
► Do not drag the TV. The floor or the product may be damaged.
PROGRAMME
VOLUME
OK
MENU
INPUT
POWER
Remote Control Sensor
Power/Standby Indicator
• Illuminates red in standby mode.
• Illuminates blue when the TV is switched on.
SPEAKER
Only 32/37/42/47LD45 **
 
						

							
A-16
PREPARATION
PREPARATION
Only 32/37/42/47LD42**,
 26/32LD32
**,
 26/32LD33
**
Remote Control Sensor
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates blue when the TV is 
switched on.
SPEAKER
PROGRAMME
VOLUME
OK
MENU
INPUT
POWER
Only 32/37/42/47LD42 **, 
32LD32 **, 32LD33
**
PROGRAMME
VOLUMEMENUPOWER
OKINPUT
Only 26LD32 **, 26LD33
**