Lexmark X945e User Manual

ARE THE PAPER SIZE AND PAPER TYPE SETTINGS THE SAME FOR EACH TRAY?
Print a menu settings page and compare the settings for each tray.
If necessary, adjust the settings from the Paper Size/Type menu.
Note: The multipurpose feeder does not automatically sense the paper size. You must set the size from the Paper
Size/Type menu.
Large jobs do not collate
These are possible solutions. Try one or more of the following:
MAKE SURE COLLATE IS SET TO ON
From the Finishing menu or Print Properties, set Collate to...

Solving copy problems
Copier does not respond
These are possible solutions. Try one or more of the following:
ARE THERE ANY ERROR MESSAGES ON THE DISPLAY?
Clear any error messages.
CHECK THE POWER
Make sure the printer is plugged in, the power is on, and Ready appears.
Scanner unit does not close
Make sure there are no obstructions:
1Lift the scanner unit.
2Remove any obstruction keeping the scanner unit open.
3Lower the scanner unit.
Poor copy quality
These are some examples of poor copy quality:
Blank...

IS THE SCANNER GLASS DIRTY?
Clean the scanner glass with a clean, lint‑free cloth dampened with water.
IS THE COPY TOO LIGHT OR TOO DARK?
Adjust the density of the copy.
CHECK THE QUALITY OF THE ORIGINAL DOCUMENT
Make sure the quality of the original document is satisfactory.
CHECK THE DOCUMENT PLACEMENT
Make sure the document or photo is loaded facedown on the scanner glass in the upper left corner.
UNWANTED TONER IS IN THE BACKGROUND
Increase the background removal setting.
Adjust the darkness to a...

CHECK THE PAPER SIZE SETTING
Make sure the Paper Size setting matches the paper loaded in the tray.
Solving scanner problems
Checking an unresponsive scanner
If your scanner is not responding, make sure:
The three cables located on the back of the scanner are attached to the printer securely.
The printer is turned on.
The printer cable is securely attached to the printer and the host computer, print server, option, or other network
device.
The power cord is plugged into the printer and a properly...

Poor scanned image quality
These are possible solutions. Try one or more of the following:
ARE THERE ANY ERROR MESSAGES ON THE DISPLAY?
Clear any error messages.
IS THE SCANNER GLASS DIRTY?
Clean the scanner glass with a clean, lint‑free cloth dampened with water.
ADJUST THE SCAN RESOLUTION
Increase the resolution of the scan for a higher quality output.
CHECK THE QUALITY OF THE ORIGINAL DOCUMENT
Make sure the quality of the original document is satisfactory.
CHECK THE DOCUMENT PLACEMENT
Make sure the...

CHECK THE CABLE CONNECTIONS
Make sure the network or USB cable is securely connected to the computer and the printer.
Solving fax problems
Caller ID is not shown
Contact your telecommunications company to verify that your telephone line is subscribed to the caller ID service.
If your region supports multiple caller ID patterns, you may have to change the default setting. There are two settings
available: FSK (pattern 1) and DTMF (pattern 2). The availability of these settings by way of the Fax menu...

REVIEW THIS DIGITAL PHONE SERVICE CHECKLIST
The fax modem is an analog device. Certain devices can be connected to the printer so that digital telephone services
can be used.
If you are using an ISDN telephone service, connect the printer to an analog telephone port (an R-interface port)
on an ISDN terminal adapter. For more information and to request an R-interface port, contact your ISDN provider.
If you are using DSL, connect to a DSL filter or router that will support analog use. For more...

CHECK THE RING COUNT DELAY SETTINGS
The ring count delay sets the number of times the phone line rings before the printer answers in Fax Only or Fax Tel
modes. If you have extension phones on the same line as the printer, or subscribe to the telephone companys
Distinctive Ring service, keep the Ring Delay setting at 4.
1Open a Web browser.
2In the address bar, type the IP address of the printer, and then press Enter.
3Click Configuration.
4Click Fax Settings.
5Click Analog Fax Setup.
6In the Rings to...

Received fax has poor print quality
These are possible solutions. Try one or more of the following:
CAN THE DOCUMENT BE RE‑SENT?
Ask the person who sent you the fax to:
Check that the quality of the original document is satisfactory.
Resend the fax. There may have been a problem with the quality of the telephone line connection.
Increase the fax scan resolution, if possible.
IS THE TONER LOW?
When 88  toner low appears or when you experience faded print, replace the cartridge(s).
MAKE SURE THE FAX...

Solving option problems
Option does not operate correctly or quits after it is installed
These are possible solutions. Try one or more of the following:
RESET THE PRINTER
Turn the printer off, wait for about 10 seconds, and then turn the printer on.
CHECK TO SEE IF THE OPTION IS CONNECTED TO THE PRINTER
1Turn the printer off.
2Unplug the printer.
3Check the connection between the option and the printer.
MAKE SURE THE OPTION IS INSTALLED
Print a menu settings page and check to see if the option is listed...