Lexmark X940e Owners Manual

General information1-49
7510
Go Back Previous
Next
Sensor (ADF pre-registration)
ADF feed motor assembly
Sensor (sheet through)
ADF registration
motor
Sensor (ADF registration)
Sensor (ADF inverter)
Sensor (ADF APS 1)Sensor (ADF APS 2)Sensor (ADF APS 3)Inverter solenoid assembly 

1-50Service Manual 7510
Go Back Previous
Next
Control 
Document size detection at scanner unit assembly
The width (fast-scan-directional size) of the document sheet on the Platen Grass is detected with the CCD 
image sensor, and the length (slow-scanning-directional size) is detected with the sensor (platen length APS 1) 
and the sensor (platen length APS 2).
Document size detection timing
The size of the document sheet on the platen glass is detected at the following timings:
•When the Platen Cover...

General information1-51
7510
Go Back Previous
Next
Shown below are the combinations of document size, detection range in the fast scanning direction, and 
sensors. 
Document SizeWidth (Fast scanning 
direction: mm)Length (Slow scanning direction) Area
Fast 
scanning 
WidthDetection 
RangeSensor (platen 
length APS 1)Sensor (platen 
length APS 2)012
Japanese Post 
Card SEF100.0 90–115 Off Off X X N
Post Card SEF 101.6NOX
A6 SEF 105.0ONO
5 X 7 SEF 127.0 115–138 Off Off N O N
B6 SEF 128.0ONO
5.5 X 8.5 SEF...

1-52Service Manual 7510
Go Back Previous
Next
O: Detectable by default.
N: Detectable by replacing the document size marked as O with the system data having the same detection 
information.
X: Not detectable.
*1: Changeable from 5.5 X 8.5 LEF to A5 LEF, or from 8.5 X 11 SEF to A4 SEF by the system data.
*2: Changeable from B5 LEF or 8.5 X 11 LEF to 8 X 10.5 LEF by the system data.
*3: Detectable by setting the system data.
*4: Changeable from Executive LEF to 8 X10 LEF.
*5: Changeable from A4 LEF to 8.5...

General information1-53
7510
Go Back Previous
Next
The standard document sizes to be identified by the same given detection information are defined on an 
area-by-area basis. Each area is to be set in the system data.
ADF side 1ADF side 2
LexmarkX000
QuickTestD
e
v
i
c
e
I
n
f
o
r
m
a
t
i
o
nMARGINSET
TINGS
Flatbed
Leading
edges
LexmarkX000
QuickTestD
e
vice
Inform
atio
n
M
A
R
G
I
N 

1-54Service Manual 7510
Go Back Previous
Next
The table below shows the combinations of document sizes and sensors. 
O: Detectable
X: Not Detectable
While the document is traveling, document size detection is performed as follows.
When the document goes through the sensor (ADF APS 1), sensor (ADF APS 2) and the sensor (ADF APS 3), 
the document width in the fast scanning direction is detected according to the combination of shielded/
unshielded status of each sensor.
The document length in the slow...

General information1-55
7510
Go Back Previous
Next
The CCD image sensor is used to read image data from the document. To stabilize the read image data, the 
CCD image sensor output is adjusted and the read image data is compensated.
The CCD image sensor output is adjusted with the gain/offset voltage of the amplifier in the analog circuit. This 
adjustment includes AGC and AOC.
In addition, the reference data is collected and compensation values are calculated to compensate for the read 
image data. This...

1-56Service Manual 7510
Go Back Previous
Next
TTM theory 

General information1-57
7510
Go Back Previous
Next
Media transport 
Media transport path
Media is supplied from tray 2, tray 3 or tray 4, and is transported to the printer along the media transport path 
shown below.
Pick rollPick roll
Separation rollSeparation roll
Feed roll
Transfer belt 2nd transfer roll assembly
Heat roll
Pressure roll
Fuser unit ASM
Standard media
exit roll assembly
Duplex media transport roll ASM
Duplex mediaCenter transport
roll ASM
Tray 3Tray 4
Feed roll
Tray module media...

1-58Service Manual 7510
Go Back Previous
Next
Media transport path
The following is a cross section of the printer and the tandem tray module, showing the main components 
directly associated with the media path and transport.  
Functions of main components
When the TTM is installed under the printer, additional trays are available.
Media tray assembly
It is necessary to adjust the rear side guides in the media tray assembly to match the media size.
Rear media guide
The rear media guide can be adjusted...