Lexmark X2600 User Manual

							6Plug the power cord into an electrical outlet that other electrical devices have been using.
7Press  to turn the printer on.
Software did not install
If you encountered problems while installing, or if your printer does not appear in the list in the Printers folder or as
a printer option when sending a print job, you can try uninstalling and reinstalling the software.
These are some other possible solutions. Try one or more of the following:
MAKE SURE YOUR OPERATING SYSTEM IS SUPPORTED
The following operating systems are supported: Windows Vista, Windows XP, Windows 2000 with Service Pack 3
or later, and Mac OS X versions 10.5, 10.4 and 10.3.
CHECK THAT YOUR COMPUTER MEETS THE MINIMUM SYSTEM REQUIREMENTS LISTED ON THE
PRINTER
 BOX
CHECK THE USB CONNECTION
1Check the USB cable for any obvious damage. If the cable is damaged, use a new one.
2Firmly plug the square end of the USB cable into the back of the printer.
3Firmly plug the rectangular end of the USB cable into the USB port of the computer.
The USB port is marked with the 
 USB symbol.
RECONNECT THE POWER SUPPLY
1Press  to turn the printer off.
2Disconnect the power cord from the wall outlet.
3Gently remove the power supply from the printer.
4Reconnect the power supply to the printer.
5Plug the power cord into the wall outlet.
6Press  to turn the printer on.
TEMPORARILY DISABLE SECURITY PROGRAMS IN WINDOWS
1Close all open programs.
2Disable any security programs.
3Do one of the following:
In Windows Vista, click .
In Windows XP and earlier, click Start.
4Click Computer or My Computer.
5Double-click the CD or DVD drive icon.
 
51
Downloaded From ManualsPrinter.com Manuals 
						

							6If necessary, double-click setup.exe.
7Follow the instructions on the computer screen to install the software.
8When the installation is completed, enable the security software again.
Page does not print
These are possible solutions. Try one or more of the following:
CHECK MESSAGES
If an error message appears, then resolve the error before trying to print again.
CHECK POWER
If the  light is not on, then make sure that the power cord is properly connected to the printer and plugged into
a known working electrical outlet that other electrical devices have been using.
REMOVE AND THEN RELOAD PAPER
CHECK INK
Check the ink levels, and then install new print cartridges if necessary.
CHECK CARTRIDGES
1Remove the print cartridges.
2Make sure the sticker and tape have been removed.
12
12
3Reinsert the cartridges.
CHECK PRINTER DEFAULT AND PAUSE SETTINGS
Using Windows
1
Do one of the following:
In Windows Vista
aClick .
bClick Control Panel.
 
52
Downloaded From ManualsPrinter.com Manuals 
						

							cUnder Hardware and Sound, click Printer.
In Windows XP
aClick Start.
bClick Printers and Faxes.
In Windows 2000
aClick Start.
bClick Settings ΠPrinters.
2Double-click the printer.
3Click Printer.
Make sure no check mark appears next to Pause Printing.
If a check mark does not appear next to Set As Default Printer, then you must select the printer for each file
that you want to print.
Using Macintosh
For Mac OS X version 10.5
1From the Finder desktop, click  ΠSystem Preferences ΠPrint & Fax.
2From the Default Printer pop-up menu, check if the printer is the default printer.
If the printer is not the default printer, then you must select the printer for each file that you want to print.
If you want to set the printer as the default printer, then select the printer from the Default Printer pop-up
menu.
3Click Open Print Queue.
The print queue dialog appears.
Make sure that the print job is not on hold. If the print job is on hold:
If you want to resume a particular print job, choose the document name, and then click Resume.
If you want to resume all print jobs in the queue, then click Resume Printer.
For Mac OS X version 10.4 and earlier
1From the Finder desktop, click Go ΠUtilities ΠPrint Center or Printer Setup Utility.
The Printer List dialog appears.
2Double-click the printer.
The print queue dialog appears.
Make sure that the print job is not on hold.
If the print job is on hold:
–If you want to resume a particular print job, choose the document name, and then click Resume.
–If you want to resume all print jobs in the queue, then click Start Jobs.
If the printer is not in bold, then it is not the default printer. You must select the printer for each file that
you want to print.
 
53
Downloaded From ManualsPrinter.com Manuals 
						

							If you want to set the printer as the default printer:
aGo back to the Printer List dialog, and then select the printer.
bClick Make Default.
DISCONNECT AND RECONNECT POWER SUPPLY
1Press  to turn off the printer.
2Disconnect the power cord from the wall outlet.
3Remove the power supply from the printer.
4Reconnect the power supply to the printer.
5Plug the power cord into the wall outlet.
6Press  to turn on the printer.
REMOVE AND REINSTALL THE SOFTWARE
If you encountered problems while installing, or if your printer does not appear in the printers folder or as a printer
option when sending a print job, then try uninstalling and reinstalling the software.
Removing and reinstalling the software
If the printer is not functioning properly, or if a communications error message appears when you try to use the
printer, you may need to remove and reinstall the printer software.
Using Windows
1Do one of the following:
In Windows Vista, click .
In Windows XP, click Start.
2Click Programs or All Programs, and then select the printer program folder from the list.
3Select Uninstall.
4Follow the instructions on the computer screen to remove the printer software.
5Restart the computer before reinstalling the printer software.
6Click Cancel on all New Hardware Found screens.
7Insert the installation CD, and then follow the instructions on the computer screen to reinstall the software.
If the install screen does not appear automatically after you restart your computer, do one of the following:
In Windows Vista:
a
Click .
bLocate the Start Search box.
cType D:\setup.exe, where D is the letter of your CD or DVD drive.
 
54
Downloaded From ManualsPrinter.com Manuals 
						

							In Windows XP:
a
Click Start ΠRun.
bType D:\setup.exe, where D is the letter of your CD or DVD drive.
Using Macintosh
1Close all open software applications.
2From the Finder desktop, double-click the printer folder.
3Double-click the Uninstaller icon.
4Follow the instructions on the computer screen to remove the printer software.
5Restart the computer before reinstalling the printer software.
6Insert the installation CD, and then follow the instructions on the computer screen to reinstall the software.
If the software still does not install correctly, visit our Web site at www.lexmark.com to check for the latest software.
1In all countries or regions except the United States, select your country or region.
2Click the links for drivers or downloads.
3Select your printer family.
4Select your printer model.
5Select your operating system.
6Select the file that you want to download, and then follow the directions on the computer screen.
Enabling the USB port in Windows
To confirm that the USB port is enabled on the computer:
1Do one of the following:
In Windows Vista
aClick  ΠControl Panel.
bClick System and Maintenance ΠSystem.
cClick Device Manager.
In Windows XP
aClick Start.
bClick Control Panel ΠPerformance and Maintenance ΠSystem.
cFrom the Hardware tab, click Device Manager.
In Windows 2000
aClick Start.
bClick Settings ΠControl Panel ΠSystem.
cFrom the Hardware tab, click Device Manager.
 
55
Downloaded From ManualsPrinter.com Manuals 
						

							2Click the plus sign (+) beside Universal Serial Bus Controller.
If USB Host Controller and USB Root Hub are listed, then the USB port is enabled.
For more information, see the computer documentation.
Solving printer power problems
The printer and the computer cannot exchange data.
These are possible solutions. Try one or more of the following:
MAKE SURE THE PRINTER POWER SUPPLY IS ATTACHED CORRECTLY
1Press  to turn the printer off.
2Disconnect the power cord from the wall outlet.
3Remove the power supply from the printer.
4Reconnect the power supply to the printer.
5Plug the power cord into the wall outlet.
6Press  to turn the printer on.
MAKE SURE THE PRINTER IS NOT IN SLEEP MODE
If the power light is blinking on and off slowly, then the printer is in sleep mode.
1Unplug the power cord from the wall outlet.
2Wait ten seconds, and then insert the power cord into the wall outlet.
3Press  to turn the printer on.
 
56
Downloaded From ManualsPrinter.com Manuals 
						

							Notices
Product information
Product name:
Lexmark 2600 Series
Machine type:
4433
Model(s):
001
Edition notice
January 2008
The following paragraph does not apply to any country where such provisions are inconsistent with local
law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in
certain transactions; therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the
information herein; these changes will be incorporated in later editions. Improvements or changes in the products
or the programs described may be made at any time.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make
these available in all countries in which it operates. Any reference to a product, program, or service is not intended
to state or imply that only that product, program, or service may be used. Any functionally equivalent product,
program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation
and verification of operation in conjunction with other products, programs, or services, except those expressly
designated by the manufacturer, are the user’s responsibility.
For Lexmark technical support, visit support.lexmark.com.
For information on supplies and downloads, visit www.lexmark.com.
If you don't have access to the Internet, you can contact Lexmark by mail:
Lexmark International, Inc.
Bldg 004-2/CSC
740 New Circle Road NW
Lexington, KY 40550
USA
© 2008 Lexmark International, Inc.
All rights reserved.
 
57
Downloaded From ManualsPrinter.com Manuals 
						

							UNITED STATES GOVERNMENT RIGHTS
This software and any accompanying documentation provided under this agreement are commercial computer
software and documentation developed exclusively at private expense.
Trademarks
Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United
States and/or other countries.
evercolor and PerfectFinish are trademarks of Lexmark International, Inc.
All other trademarks are the property of their respective owners.
Licensing notices
The following document can be viewed from the \Drivers\XPS directory on the installation software CD: Zopen.PDF.
Federal Communications Commission (FCC) compliance information
statement
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation.
The FCC Class B limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult your point of purchase or service representative for additional suggestions.
The manufacturer is not responsible for radio or television interference caused by using other than recommended
cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could
void the user's authority to operate this equipment.
Note: To assure compliance with FCC regulations on electromagnetic interference for a Class B computing device,
use a properly shielded and grounded cable such as Lexmark part number 1021294 for USB attach. Use of a substitute
cable not properly shielded and grounded may result in a violation of FCC regulations.
Any questions regarding this compliance information statement should be directed to:
Director of Lexmark Technology & Services
Lexmark International, Inc.
740 West New Circle Road
Lexington, KY 40550
(859) 232–3000
 
58
Downloaded From ManualsPrinter.com Manuals 
						

							Exposure to radio frequency radiation
The following notice is applicable if your printer has a wireless network card installed.
The radiated output power of this device is far below the radio frequency exposure limits of the FCC and other
regulatory agencies. A minimum separation of 20 cm (8 inches) must be maintained between the antenna and any
persons for this device to satisfy the RF exposure requirements of the FCC and other regulatory agencies.
Industry Canada compliance statement
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Standard
ICES-003.
Avis de conformité aux normes de l’industrie du Canada
Cet appareil numérique de classe B est conforme aux exigences de la norme canadienne relative aux équipements
pouvant causer des interférences NMB-003.
Industry Canada notice
The following notices are applicable if your printer has a wireless network card installed.
Industry Canada (Canada)
This device complies with Industry Canada specification RSS-210. Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
This device has been designed to operate only with the antenna provided. Use of any other antenna is strictly
prohibited per regulations of Industry Canada.
To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from
windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to
licensing.
The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit
RF fields in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health
Canada's Web site www.hc-sc.gc.ca/rpb.
The term "IC:" before the certification/registration number only signifies that the Industry Canada technical
specifications were met.
Industry Canada (Canada)
Cet appareil est conforme à la norme RSS-210 d'Industry Canada. Son fonctionnement est soumis aux deux conditions
suivantes :
(1) cet appareil ne doit pas provoquer d'interférences et (2) il doit accepter toute interférence reçue, y compris celles
risquant d'altérer son fonctionnement.
Cet appareil a été conçu pour fonctionner uniquement avec l'antenne fournie. L'utilisation de toute autre antenne
est strictement interdite par la réglementation d'Industry Canada.
 
59
Downloaded From ManualsPrinter.com Manuals 
						

							En application des réglementations d'Industry Canada, l'utilisation d'une antenne de gain supérieur est strictement
interdite.
Pour empêcher toute interférence radio au service faisant l'objet d'une licence, cet appareil doit être utilisé à l'intérieur
et loin des fenêtres afin de garantir une protection optimale.
Si le matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence.
L'installateur de cet équipement radio doit veiller à ce que l'antenne soit implantée et dirigée de manière à n'émettre
aucun champ HF dépassant les limites fixées pour l'ensemble de la population par Santé Canada. Reportez-vous au
Code de sécurité 6 que vous pouvez consulter sur le site Web de Santé Canada www.hc-sc.gc.ca/rpb.
Le terme « IC » précédant le numéro de d'accréditation/inscription signifie simplement que le produit est conforme
aux spécifications techniques d'Industry Canada.
European Community (EC) directives conformity
This product is in conformity with the protection requirements of EC Council directives 2004/108/EC and 2006/95/EC
on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility
and safety of electrical equipment designed for use within certain voltage limits.
A declaration of conformity with the requirements of the directives has been signed by the Director of Manufacturing
and Technical Support, Lexmark International, Inc., S.A., Boigny, France.
This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.
European EC directives conformity statement for radio products
The following notices are applicable if your printer has a wireless network card installed
This product is in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC,
and 1999/5/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic
compatibility, safety of electrical equipment designed for use within certain voltage limits and on radio equipment
and telecommunications terminal equipment.
Compliance is indicated by the CE marking.
The Alert sign indicates that there are restrictions within certain member states.
A declaration of conformity with the requirements of the directives is available from the Director of Manufacturing
and Technical Support, Lexmark International, S. A., Boigny, France.
The following restrictions apply:
Country/region
Restriction
All countries/regionsThis product is for indoor use only. This product may not be used outdoors.
L'ItaliaSi fa presente inoltre che l'uso degli apparati in esame è regolamentato da:
D.Lgs 1.8.2003, n.259, articoli 104 (attività soggette ad autorizzazione generale) e 105
(libero uso), per uso privato;
D.M. 28.5.03, per la fornitura al pubblico dell'accesso R-LAN alle reti e ai servizi di
telecomunicazioni.
 
60
Downloaded From ManualsPrinter.com Manuals