Lexmark T654n User Manual

Ordering a maintenance kit
When 80 Routine maintenance needed appears, order a maintenance kit. The maintenance kit contains all
the items necessary to replace the pick rollers, the charge roll, the transfer roller, and the fuser.
Notes:
Using certain types of paper may require more frequent replacement of the maintenance kit. The charge roll,
fuser, pick rollers, and transfer roller can also be individually ordered and replaced as necessary.
To check the fuser type (T1 or T2) installed in the printer,...

Ordering pick rollers
When the paper fails to properly feed from the tray, order new pick rollers.
Part namePart number
Pick rollers 40X4308
Ordering staple cartridges
When Staples Low or Staples Empty appears, order the specified staple cartridge.
For more information, see the illustrations inside the stapler door.
Part namePart number
Staple Cartridges–3 pack 25A0013
Ordering a transfer roller
When toner smudges appear on the front or back of printed pages, order a replacement transfer roller.
Part...

CAUTION—POTENTIAL INJURY:  Before moving the printer, follow these guidelines to avoid personal injury or
printer damage:
Turn the printer off using the power switch, and then unplug the power cord from the wall outlet.
Disconnect all cords and cables from the printer before moving it.
Lift the printer off of the optional drawer and set it aside instead of trying to lift the drawer and printer at the same
time.
Note: Use the handholds located on both sides of the printer to lift it off the optional...

Administrative support
Finding advanced networking and administrator information
This chapter covers basic administrative support tasks. For more advanced system support tasks, see the Networking
Guide on the Software and Documentation CD and the Embedded Web Server Administrators Guide on the Lexmark
Web site at www.lexmark.com.
Using the Embedded Web Server
If the printer is installed on a network, the Embedded Web Server is available for a range of functions including:
Viewing a virtual display of the...

To set up e‑mail alerts:
1Type the printer IP address into the address field of your Web browser.
Note: If you do not know the IP address of the printer, then print a network setup page and locate the IP
address in the TCP/IP section.
2Click Settings.
3Under Other Settings, click E‑mail Alert Setup.
4Select the items for notification, and type in the e‑mail addresses.
5Click Submit.
Note: See your system support person to set up the e‑mail server.
Viewing reports
You can view some reports from the...

3Press the arrow buttons until Settings appears, and then press .
4Press the arrow buttons until General Settings appears, and then press .
5Press the arrow buttons until Timeouts appears, and then press .
6Press the arrow buttons until Power Saver appears, and then press .
7Press the arrow buttons to increase or decrease the number of minutes before the printer enters Power Saver
mode, and then press 
.
Restoring the factory default settings
If you want to retain a list of the current menu settings for...

Troubleshooting
Solving basic problems
Solving basic printer problems
If there are basic printer problems, or the printer is unresponsive, make sure:
The power cord is plugged into the printer and a properly grounded electrical outlet.
The electrical outlet is not turned off by any switch or breaker.
The printer is not plugged into any surge protectors, uninterrupted power supplies, or extension cords.
Other electronic equipment plugged into the outlet is working.
The printer is turned on. Check the...

Solving printing problems
Multiple‑language PDFs do not print
The documents contain unavailable fonts.
1Open the document you want to print in Adobe Acrobat.
2Click the printer icon.
The Print dialog appears.
3Select Print as image.
4Click OK.
Error message about reading USB drive appears
Make sure the USB drive is supported. For information regarding tested and approved USB flash memory devices, visit
the Lexmark Web site at www.lexmark.com.
Jobs do not print
These are possible solutions. Try one or...

MAKE SURE YOU ARE USING A RECOMMENDED USB, SERIAL, OR ETHERNET CABLE
For more information, visit the Lexmark Web site at www.lexmark.com.
MAKE SURE PRINTER CABLES ARE SECURELY CONNECTED
Check the cable connections to the printer and print server to make sure they are secure.
For more information, see the setup documentation that came with the printer.
Confidential and other held jobs do not print
These are possible solutions. Try one or more of the following:
PARTIAL JOB, NO JOB, OR BLANK PAGES PRINT
The...

Job prints from the wrong tray or on the wrong paper
C
HECK THE PAPER TYPE SETTING
Make sure the paper type setting matches the paper loaded in the tray:
1From the printer control panel, check the Paper Type setting from the Paper menu.
2Before sending the job to print, specify the correct type setting:
For Windows users, specify the type from Print Properties.
For Macintosh users, specify the type from the Print dialog.
Incorrect characters print
M
AKE SURE THE PRINTER IS NOT IN HEX TRACE MODE
If Ready...