Lexmark T652dtn User Manual

Menu itemDescription
Std Network Setup
Reports or Network Reports
Network Card
TCP/IP
IPv6
AppleTalk
NetWare
LexLink
Net  Setup
Reports or Network Reports
Network Card
TCP/IP
IPv6
Wireless
AppleTalk
NetWare
LexLinkFor descriptions and settings of the network setup menus, see the following:
“Network Reports menu” on page 111
“Network Card menu” on page 111
“TCP/IP menu” on page 112
“IPv6 menu” on page 113
“Wireless menu” on page 113
“AppleTalk menu” on page 114
“NetWare menu” on page 114
“LexLink menu” on...

Menu itemDescription
Network Address
UAA
LAALets you view the network addresses
Job Timeout
0‑225 secondsSets the amount of time in seconds that a network print job can take before it
is canceled
Notes:
90 seconds is the factory default setting.
A setting value of 0 disables the timeout.
If a value of 1–9 is selected, then the setting is saved as 10.
Banner Page
Off
OnAllows the printer to print a banner page
Note: Off is the factory default setting.
TCP/IP menu
Use the following menu items to view or...

Menu itemDescription
Enable BOOTP
On
OffSpecifies the BOOTP address assignment setting
Note: On is the factory default setting.
AutoIP
Yes
NoSpecifies the Zero Configuration Networking setting
Note: Yes is the factory default setting.
Enable FTP/TFTP
Yes
NoEnables the built-in FTP server, which allows you to send files to the printer using the
File Transfer Protocol.
Note: Yes is the factory default setting.
Enable HTTP Server
Yes
NoEnables the built-in web server (Embedded Web Server). When enabled, the...

This menu is available from the Network/Ports menu:
Network/Ports > Network  > Net  Setup > Wireless
Menu itemDescription
Network Mode
Infrastructure
Ad hocSpecifies the network mode
Notes:
Infrastructure mode lets the printer access a network using an
access point.
Ad hoc is the factory default setting. Ad hoc mode configures the
printer for wireless networking directly between it and a computer.
Compatibility
802.11n
802.11b/g
802.11b/g/nSpecifies the wireless standard for the wireless network
Choose...

Menu itemDescription
Activate
Yes
NoActivates NetWare support
Note: No is the factory default setting.
View Login NameLets you view the assigned NetWare login name
Note: This can be changed only from the Embedded Web Server.
Print ModeLets you view the assigned NetWare print mode
Note: This can be changed only from the Embedded Web Server.
Network NumberLets you view the assigned NetWare network number
Note: This can be changed only from the Embedded Web Server.
Select SAP Frames
Ethernet 802.2
Ethernet...

Standard USB menu
Menu itemDescription
PCL SmartSwitch
On
OffSets the printer to automatically switch to PCL emulation when a print job received
through a USB port requires it, regardless of the default printer language
Notes:
On is the factory default setting.
When the Off setting is used, the printer does not examine incoming data.
When the Off setting is used, the printer uses PostScript emulation if the PS
SmartSwitch setting is On. It uses the default printer language specified in the
Setup menu if...

Menu itemDescription
Job Buffering
Off
On
AutoTemporarily stores jobs on the printer hard disk before printing
Notes:
Off is the factory default setting.
The On setting buffers jobs on the printer hard disk.
The Auto setting buffers print jobs only if the printer is busy processing data
from another input port.
Changing this setting from the printer control panel and then exiting the
menus causes the printer to restart. The menu selection is updated.
Mac Binary PS
On
Off
AutoSets the printer to process...

Menu itemDescription
NPA Mode
On
Off
AutoSets the printer to perform the special processing required for bidirectional
communication following the conventions defined by the NPA protocol
Notes:
Auto is the factory default setting.
Changing this setting from the printer control panel and then exiting the
menus causes the printer to restart. The menu selection is updated.
Parallel Buffer
Disabled
Auto
3K to Sets the size of the parallel input buffer
Notes:
Auto is the factory default setting.
The Disabled...

Menu itemDescription
Honor Init
On
OffDetermines whether or not the printer honors printer hardware initialization
requests from the computer
Notes:
Off is the factory default setting.
The computer requests initialization by activating the Init signal from the
parallel port. Many personal computers activate the Init signal each time the
computer is turned on.
Parallel Mode 2
On
OffDetermines whether the parallel port data is sampled on the leading or trailing edge
of strobe
Notes:
On is the factory...

Menu itemDescription
PS SmartSwitch
On
OffSets the printer to automatically switch to PS emulation when a print job received
through a serial port requires it, regardless of the default printer language
Notes:
On is the factory default setting.
When the Off setting is used, the printer does not examine incoming data.
When the Off setting is used, the printer uses PCL emulation if PCL
SmartSwitch is set to On. It uses the default printer language specified in the
Setup menu if PCL SmartSwitch is set to...