Lexmark T622IN User Manual

							20
Installing an optional firmware cardFollow the instructions in this section to install an 
optional firmware card. The system board has one 
connection point for firmware cards.
Warning!Optional firmware cards are easily damaged by 
static electricity. Touch something metal on the 
printer before you touch a card.1Access the system board. (See page 17 for 
instructions.)
2Locate the holes on the system board near 
the option card connectors.
3Unpack the firmware card.
Avoid touching the metal pins on the bottom 
of the card. Save the packaging.
4Holding the firmware card by its sides, align 
the two pins on the card with the holes on 
the system board.
Orient the card so that the pins are closest 
to the edge of the board.
5Push in until the firmware card is firmly in 
place.
Resting posts
Pins
Card
Connectors
Downloaded From ManualsPrinter.com Manuals 
						

							21
 Installing an option cardYour printer has two connectors that support the 
following option cards:
Hard disk with adapter card
MarkNet™ internal print server
USB/Parallel 1284-C Interface Card
Parallel 1284-C Interface Card
Coax/Twinax Adapter for SCS
Tr i - P o r t  A d a p t e r
Refer to the documentation included with each 
card for detailed information about that specific 
card.
You need a small Phillips screwdriver to install 
these options.
Note:The Lexmark T622n model ships with an 
Ethernet print server already installed.
Warning!
Electronic components are easily damaged by 
static electricity. Touch something metal on the 
printer before you touch the card.1Follow the steps in “Accessing the printer 
system board” beginning on page 17.
2Locate the card connectors on the system 
board. If you are installing only one card, 
install it in connector 1. If you are installing 
two cards on a model with multiple 
connectors, use connector 1 first and then 
connector 2.
3Locate the two screws on the back of the 
printer that attach the metal plate to the slot. 
4Remove and save the two screws. Remove 
and discard the plate.
5Unpack the card. Save the packaging 
materials.
MarkNet internal print server
Tri-Port adapter
hard disk with adapter USB/Parallel 1284-C interface card MarkNet N2501e or N2401e
Connector 1
Connector 2
Downloaded From ManualsPrinter.com Manuals 
						

							226
Align the connection points on the card with 
the connector on the system board and push 
the card firmly into the system board 
connector.
7Insert the two screws saved from the metal 
plate (or the extra screws shipped with the 
card) into the holes.
8Tighten the screws to secure the card.
Reattaching the shield and closing
the doorsAfter you have installed option cards on the printer 
system board, follow these steps to reattach the 
shield and close the doors. 
 
1Grasp the shield by the tabs and align the 
three keyholes on the shield with the top 
three screws. Holding the shield by the tabs, 
slide it down onto the screws. Tighten all six 
screws.
 
2Close the side door. 
3Close the upper and lower front doors.
Note:If you have not completed the section 
“Setting up the printer” beginning on 
page 7, do so now.
Tabs
Downloaded From ManualsPrinter.com Manuals 
						

							23
Step 3: Load print material
Complete these instructions to load print material 
into any of the standard or optional trays. All paper 
trays are loaded in the same way.
1Remove the paper tray.
2Pull the width guide tab and slide the width 
guide to the far right side of the tray.
3Squeeze the length guide lever and slide the 
length guide to the correct position for the 
size paper you are loading.
Note:If a finisher is installed on the printer, see 
the Lexmark T Family Quick Reference or 
the Lexmark T620/T622 Publications CD 
for special paper loading instructions.
.
4Place the paper into the paper tray with the 
recommended print side face down for 
single-sided printing and face up for duplex 
printing. Do not fill paper above the paper 
capacity mark (fill line). 
5Pull the width guide tab and slide the width 
guide
 to the left until it lightly rests against 
the edge of the paper stack.
6Adjust the knob to show the size of the 
paper currently loaded.
Note:This setting serves as a visual reminder 
only; it has no effect on the operation of 
the printer.
7Reinstall the tray. 
Width guideWidth guide 
tab
Paper size indicatorsLength guide
Length guide 
lever
Width guideWidth 
guide tab
Paper capacity 
mark
Knob
Downloaded From ManualsPrinter.com Manuals 
						

							24
Step 4: Attach cables
You can attach your printer to a network or locally 
(directly to a computer).
Network printingYou can attach your printer to a network using stan-
dard network cables.
A 10BaseT/100BaseTX Fast Ethernet port is standard 
on the Lexmark T622n. You can add a Token-Ring or 
10Base2 Ethernet port to either printer model by 
installing an optional MarkNet internal print server.
To attach the printer to a network:
1Make sure the printer is turned off and 
unplugged.
2Connect the printer to a LAN drop or hub using 
standard cabling that is compatible with your 
network.
The printer automatically adjusts itself for the 
network speed.

						

							25

						

							26
model, you can locally attach the printer with a serial 
cable. We recommend Lexmark part number 1038693 
(50 ft). For details on LocalTalk or infrared connec-
tions, refer to the documentation that shipped with the 
Tri-Port Adapter.
Note:All Windows operating systems support parallel 
cable connections. However, only the Windows 
2000/98/Me operating systems support USB 
cable connections.
To attach the printer to a computer:
1Make sure the printer, computer, and any other 
attached devices are turned off and unplugged.
2Connect the printer to the computer using a 
parallel or USB cable.

						

							27
Step 5: Verify printer setup
Turning on the printer1Plug one end of the printer power cord into the 
socket at the back of the printer and the other end 
into a properly grounded outlet.
2Turn on the printer. If the printer is attached locally 
(directly to a computer), leave the computer and any 
other attached devices turned off. You will turn 
these on in a later step.
The printer requires time to warm up after you turn it 
on. During this period, the message Performing
Self Test appears on the operator panel display.
After the printer completes its internal tests, the 
Readymessage indicates the printer is ready to 
receive jobs.
If you see other messages on the display, refer to 
the Lexmark T620/T622 Publications CD for instruc-
tions on clearing the message. Click Printing, and 
then click Understanding printer messages.
3Go to “Printing a menu settings page” on page 28. If 
you attached the printer to a network, see“Printing a 
network setup page”.
Note:You can change the language that appears on the 
operator panel display. Refer to the Lexmark 
T620/T622 Publications CD for instructions.
Printing a network setup pageIf the printer is attached to a network, print a network 
setup page to verify the network connection. This page 
also provides important information that will help you con-
figure for network printing.
Downloaded From ManualsPrinter.com Manuals 
						

							281
Press Menu until you see Utilities Menu, and then 
press Select.
2Press Menu until you see Print Net Setup, and then 
press Select to print the page.
The network setup page prints and the printer 
returns to Ready status.
3Check the first section on the network setup page 
and confirm that Status is “Connected.”
Note:If an optional MarkNet card is installed in slot 1, you 
see Print Net1 Setup. If the card is installed in slot 
2, you see Print Net2 Setup.
If Status is “Not Connected,” your LAN drop may not 
be active or your network cable may be malfunction-
ing. Consult your network support person, and then 
print another network setup page to verify that you 
are connected to your network.
Save the network setup page for use with later 
instructions.
4See “Printing a menu settings page”.
Printing a menu settings pagePrint the menu settings page to review the default printer 
settings and to verify that printer options are installed cor-
rectly. For more information about using the printer opera-
tor panel and changing menu settings, refer to the 
Lexmark T620/T622 Publications CD.
1Press Menu until you see Utilities Menu, and then 
press Select.
2Press Menu until you see Print Menus, and then 
press Select to print the page.
The message Printing Menusis displayed.
3Verify that the options you installed are listed under 
“Installed Features.”
If an option you installed is not listed, turn the printer 
off, unplug the power cord, and reinstall the option.
4Verify the amount of memory installed is correctly 
listed under “Printer Information.”
5Verify that the paper trays are configured for the 
sizes and types of paper you loaded in the printer.
Downloaded From ManualsPrinter.com Manuals 
						

							29
Step 6: Configure for TCP/IP
If you have TCP/IP available on your network, we recommend that you assign an 
IP address to the printer.
Setting the printer
IP addressIf your network is using DHCP, an address is automatically assigned.
1Look for the address under the TCP/IP heading on the network setup page 
you printed in “Printing a network setup page” on page 27.
2Go to “Verifying the IP settings” on page 30 and begin with step 2.
Note:You can find instructions for other methods of setting the IP address in the 
online documentation on the drivers CD that shipped with your printer.
If your network is not using DHCP, then you must manually assign an IP address. 
One of the easiest ways is to use the operator panel:
1Press Menu until you see Network Menu, and then press Select.
2Press Menu until you see Standard Network, and then press Select.
Standard Network appears if you purchased a printer with an on-board net-
work port. If you have an optional MarkNet card installed in slot 1, you see 
Network Option 1. If the card is installed in slot 2, you see Network 
Option 2.
3Press Menu until you see Std Net Setup, and then press Select.
4Press Menu until you see TCP/IP, and then press Select.
5Press Menu until you see Set IP Address, and then press Select. 
6Change the address by pressing Menu to increase (or decrease) each 
number. Press Select to move to the next segment. Press Select when you 
are finished.
The message Saved appears briefly.
7Press Menu until you see Set IP Netmask, and then press Select. 
8Repeat step 6 to set the IP Netmask.
9Press Menu until you see Set IP Gateway, and then press Select. 
10Repeat step 6 to set the IP Gateway.
11When you are finished, press Go to return the printer to the Ready state.
Downloaded From ManualsPrinter.com Manuals