Lexmark E360d User Manual

1Rear door
2Ethernet port
Note: The Ethernet port is a feature on network models only.
3USB port
4Parallel port
5Printer power cord socket
6Power switch
7Locking device port
Learning about the printer
11
Downloaded From ManualsPrinter.com Manuals 

Configured models
The following illustration shows the printer configured with an optional drawer:
1Front door release button
2Paper stop
3Standard exit bin
4Printer control panel
5System board door
6Standard 250‑sheet tray (Tray 1)
7Optional 250‑ or 550‑sheet drawer (Tray 2)
8Multipurpose feeder door
9Front door
Using the standard exit bin and paper stop
The standard exit bin holds up to 150 sheets of 20 lb paper. It collects print jobs facedown. The standard exit bin includes
a paper stop that keeps...

To open the paper stop, pull it so it flips forward.
Notes:
Do not leave the paper stop in the open position if you are printing on transparencies. Doing so may cause
creases in the transparencies.
When moving the printer to another location, make sure the paper stop is closed.
Learning about the printer
13
Downloaded From ManualsPrinter.com Manuals 

Additional printer setup
Installing internal options
CAUTION—SHOCK HAZARD:  If you are accessing the system board or installing optional hardware or memory
devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the
wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well,
and unplug any cables going into the printer.
You can customize your printer connectivity and memory capacity by adding optional...

1Ethernet connector
Note: The Ethernet port is a feature on network models only.
2USB port
3Parallel connector
4Memory card connector
5Optional card connector
6Optional card connector
Installing a memory card
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory
devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the
wall outlet before continuing. If you have any other devices attached to the printer,...

An optional memory card can be purchased separately and attached to the system board. To install the memory card:
1Turn the printer off.
2Access the system board.
3Unpack the memory card.
Note: Avoid touching the connection points along the edge of the card.
4Align the memory card with its connector on the system board.
5Push open the latches on both ends of the memory connector.
Warning—Potential Damage: Memory cards are easily damaged by static electricity. Touch a grounded metal
surface before you...

It may require some force to fully seat the card.
7Ensure that each latch fits over the notch on each end of the card.
8Close the system board door.
9Turn the printer back on.
10Open the printers folder:
aClick , or click Start and then click Run.
bIn the Start Search or Run box, type control printers.
cPress Enter, or click OK.
The printers folder opens.
11Right‑click your printer icon.
12Click Properties.
13Click Install Options.
Note: Memory cards designed for other printers may not work with your...

Installing a flash memory or firmware card
The system board has two connections for an optional flash memory or firmware card. Only one of each may be installed,
but the connectors are interchangeable.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory
devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the
wall outlet before continuing. If you have other devices attached to the printer, then turn them...

4Push the card firmly into place.
Notes:
The entire length of the connector on the card must touch and be flush against the system board.
Be careful not to damage the connectors.
5Close the system board door.
Installing hardware options
Installing a 250‑ or 550‑sheet drawer
CAUTION—POTENTIAL INJURY: The printer weight is greater than 18 kg (40 lb) and requires two or more
trained personnel to move it safely.
Additional printer setup
19
Downloaded From ManualsPrinter.com Manuals 

An optional drawer attaches under the printer. A drawer consists of two parts: a tray and a support unit. The printer
supports one optional drawer; you can install a 250‑ or 550‑sheet drawer.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory
devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the
wall outlet before continuing. If you have any other devices attached to the printer, then turn them off...