Lexmark E260d User Manual

1
2 3 45
1Rear300 mm (12 in.)
2Right side200 mm (8 in.)
3Front300 mm (12 in.)
4Left side12.7 mm (0.5 in.)
5Top300 mm (12 in.)
Printer configurations
Basic model
The following illustration shows the printer front with its basic features or parts:
Learning about the printer
11
Downloaded From ManualsPrinter.com Manuals 

1Front door release button
2Paper stop
3Standard exit bin
4Printer control panel
5System board door
6Standard 250-sheet tray (Tray 1)
7Manual feeder door
8Front door
The following illustration shows the printer back with its basic features or parts:
Learning about the printer
12
Downloaded From ManualsPrinter.com Manuals 

1Rear door
2Ethernet port
Note: The Ethernet port is a feature on network models only.
3USB port
4Parallel port
5Printer power cord socket
6Power switch
7Security slot
Configured models
The following illustration shows the printer configured with an optional 250- or 550-sheet drawer:
Learning about the printer
13
Downloaded From ManualsPrinter.com Manuals 

1Front door release button
2Paper stop
3Standard exit bin
4Printer control panel
5System board door
6Standard 250-sheet tray (Tray 1)
7Optional 250- or 550-sheet drawer (Tray 2)
8Manual feeder door
9Front door
Understanding the printer control panel
The printer control panel features six lights and two buttons.
Learning about the printer
14
Downloaded From ManualsPrinter.com Manuals 

Item
1Error light
2Jam light
3Load paper light
4Toner light
5Ready light
6Continue button
7Stop button
Learning about the printer
15
Downloaded From ManualsPrinter.com Manuals 

Additional printer setup
Installing internal options
CAUTION—SHOCK HAZARD:  If you are accessing the system board or installing optional hardware or memory
devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall
outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and
unplug any cables going into the printer.
You can customize your printer connectivity and memory capacity by adding optional...

1Ethernet connector
Note: The Ethernet port is a feature on network models only.
2USB port
3Parallel connector
4Memory card connector
5Optional card connector
6Optional card connector
Installing a memory card
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory
devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall
outlet before continuing. If you have any other devices attached to the printer,...

An optional memory card can be purchased separately and attached to the system board. To install the memory card:
1Turn the printer off.
2Access the system board.
3Unpack the memory card.
Note: Avoid touching the connection points along the edge of the card.
4Align the memory card with its connector on the system board.
5Push open the latches on both ends of the memory connector.
Warning—Potential Damage: Memory cards are easily damaged by static electricity. Touch a grounded metal
surface before you...

It may require some force to fully seat the card.
7Ensure that each latch fits over the notch on each end of the card.
8Close the system board door.
9Turn the printer back on.
10Open the printers folder:
aClick , or click Start and then click Run.
bIn the Start Search or Run box, type control printers.
cPress Enter, or click OK.
The printers folder opens.
11Right-click your printer icon.
12Click Properties.
13Click Install Options.
Note: Memory cards designed for other printers may not work with your...

An optional drawer attaches under the printer. A drawer consists of two parts: a tray and a support unit. The printer
supports one optional drawer; you can install a 250- or 550-sheet drawer.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory
devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall
outlet before continuing. If you have any other devices attached to the printer, then turn them off...