Lexmark C935hdn User Manual

5Press the ribbon cable connector into the hard disk connector on the system board.
6Flip the hard disk over, and then press the three posts on the mounting plate into the holes on the system board.
The hard disk snaps into place.
7Reinstall the system board.
Installing an internal print server or port interface card
CAUTION—SHOCK HAZARD: Turn the printer off, and unplug the power cord from the wall outlet before
continuing. If you have any other devices attached to the printer, turn them off as well and...

An internal print server allows connection from the printer to the local area network (LAN). An optional port interface
card expands the ways the printer can connect to a computer or external print server.
1Access the system board.
2Unpack the internal print server or port interface card.
3Remove the metal plate on the system board tray that covers the connector slot and save the metal plate.
4Align the connector on the internal print server or port interface card with the connector on the system board....

Reinstalling the system board
Warning—Potential Damage: System board electrical components are easily damaged by static electricity. Touch
something metal on the printer before touching any system board electronic components or connectors.
Note: This operation requires a #2 Phillips screwdriver.
1Gently insert the system board into the printer.
2Replace the cover screws, and then turn them clockwise.
3Tighten the screws firmly.
Attaching cables
Connect the printer to the computer using a USB cable or...

1USB port
2Ethernet port
Installing options24
Downloaded From ManualsPrinter.com Manuals 

Loading paper and specialty media
This section explains how to load the 520-, 867-, and 1133-sheet trays, and the multipurpose feeder. It also includes
information about paper orientation, setting the Paper Size and Paper Type, and linking and unlinking trays.
Setting the Paper Size and Paper Type
The Paper Size setting is determined by the position of the paper guides in the tray for all trays except the multipurpose
feeder. The Paper Size setting for the multipurpose feeder must be set manually. The...

5Press  repeatedly until Units of Measure appears, and then press .
6Press  repeatedly until  appears next to the correct unit of measure, and then press .
Submitting Selection appears, followed by the Universal Setup menu.
Specify the paper height and width
Defining a specific height and width measurement for the Universal paper size (in the portrait orientation) allows the
printer to support the size, including support for standard features such as duplex printing and printing multiple pages
on one...

Loading the 520-sheet trays
The Size Sensing setting is only available for A5- and statement-size paper.
Loading the 520‑sheet trays
The printer has a standard 520‑sheet tra y (T ray 1 ), an d it may h ave one o r m ore o ptional 520‑sheet trays. All 520‑sheet
trays support the same paper sizes and types. Paper may be loaded in the trays in either the long‑edge or short‑edge
orientation.
1Grasp the handle, and pull the tray out.
2Squeeze the width guide tabs together as shown, and move the width guide to...

3Squeeze the length guide tab inward as shown, and slide the guide to the correct position for the paper size being
loaded.
Note: Use the size indicators on the bottom of the tray to help position the guides.
4Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the
edges on a level surface.
5Load the paper stack with the recommended print side faceup. Load the paper in either the long‑edge or short‑edge
orientation as shown below:
Notes:
Load...

7Align the tray, and insert it.
8If a different type of paper was loaded than the type previously loaded in the tray, change the Paper Type setting
for the tray from the control panel.
Using A5 or statement paper sizes
The printer trays cannot distinguish between A5‑ (148 x 210 mm) and statement‑size (140 x 216 mm) paper when both
sizes are loaded in the printer trays. From the Size Sensing menu, specify which size you want the printer to detect.
Load either A5‑ or statement‑size paper in the paper...

Loading the 867‑ and 1133‑sheet trays
Although the 867-sheet tray and the 1133-sheet tray are different in appearance, they support the same paper sizes
and types and require the same process for loading paper. Use these instructions to load paper in either tray:
1Grasp the handle, and open the tray.
2Squeeze the length guide tab inward as shown, and slide the guide to the correct position for the paper size being
loaded.
3Flex the sheets back and forth to loosen them, and then fan them. Do not fold or...