Lexmark C736 Service Manual

Repair information4-129
  5026
Go Back Previous
Next
9.Remove the four screws (G) from the bottom pan.
10.With one hand, disengage the gear (H), then grasp the paper pick assembly, and pull forward and 
downward to disengage the assembly until the front (J) and rear locking tabs release (not visible). 

4-130Service Manual 5026  
Go Back Previous
Next
11.Lower the paper pick mechanism, and remove through the front of the printer. 
Note:  Make sure the JTRAY1 and JTRAY2 connectors do not bind when passing through the frame 
access hole.
Installation notes:
1.Remove the waste toner assembly. See “Waste toner assembly removal” on page 4-174.
2.Replace the rear frame cover to protect the system board.
3.Turn the printer on its back.
4.Slide the paper pick assembly toward the back of the printer, and down to...

Repair information4-131
  5026
Go Back Previous
Next
6.Reach into the printer, and replace the front right screw (C) to secure the paper pick assembly.
7.Set the printer upright.
8.Secure the remaining three screws (D).
9.Remove the rear frame cover.
10.Route the cables through the hole in the frame, and connect them to JFDPCK1 (E) and JTRAY1 (F).
11.Replace the rear frame cover.
12.Replace the waste toner assembly. 
13.Replace the toner cartridges.
14.Replace the transfer module with the photoconductor...

4-132Service Manual 5026  
Go Back Previous
Next
Photoconductor unit removal
Not a FRU
Warning:  To avoid damaging the photoconductor drum, hold the photoconductor units by their handle and 
place the photoconductor units on a clean surface. See “Handing the photoconductor unit” on 
page 4-2 for additional information.
1.Open the front access door.
2.Lift the right end handle (A) of the photoconductor unit, releasing from the mount.
3.Lift the unit up and away from the left side of printer, ensuring the...

Repair information4-133
  5026
Go Back Previous
Next
Pick arm roll removal and replacement
See “Pick arm roll” on page 7-5 for the part number.
The autocompensator pick roll tires are located in the base printer. There are also tires in all input options. If you 
have additional input options, and you are having problems with media picking, replace these tires also. Always 
replace the pick arm rolls in pairs. The rolls come in a package of two.
Warning:  Remove only the rubber tires and not the pick...

4-134Service Manual 5026  
Go Back Previous
Next
Installation notes: Install the new rubber tires with the surface texture turning in the direction as shown.
Note:  Feel the rubber surface to verify it turns properly in the direction shown.
Printer pad removal
1.Slide the corner of the printer containing the damaged pad over the corner of the table. 
2.Remove the side cover that corresponds to the damaged pad so you can see if the pad fully seats in the 
installation holes.
3.Pull the pad tabs (A) from...

Repair information4-135
  5026
Go Back Previous
Next
Printhead removal, installation, and adjustment
See “Printhead assembly” on page 7-9 for the part number.
Service tip—Testing the new printhead
See “Printhead verification” on page 3-35 for quick way to verify that the existing printhead is failing 
before installing the new printhead. If the new printhead also fails, the existing printhead is probably 
working properly, so the system board is probably the failing component.
Printhead removal
1.
Turn...

4-136Service Manual 5026  
Go Back Previous
Next
period of time. Place a clean, dry cloth over the transfer module and photoconductor units until they are 
required.
8.Remove all of the toner cartridges.
9.Remove the right cover and the right side cover (attached). See “Right cover removal” on page 4-37. 
10.Remove the LVPS. See “Low-voltage power supply (LVPS) removal” on page 4-112. 
11.Remove the system board support shield. See “System board support shield removal” on page 4-157. 
12.Push the top...

Repair information4-137
  5026
Go Back Previous
Next
13.Remove the three printhead mounting screws (D). 

4-138Service Manual 5026  
Go Back Previous
Next
14.Remove the printhead alignment screw cover (E).
15.While still holding the printhead in place, loosen the printhead alignment screw (F) until the printhead 
comes out.
Warning:  Secure the printhead when loosening the printhead alignment screw. Failure to do this allows 
the printhead to fall out of the printer, potentially damaging the printhead. 
Install the printhead and replace parts
Warning:  
•When reinstalling the printhead, it is important to...