Lexmark C 950 Service Manual

Repair information 4-227
  5058-030
Go Back Previous
Next
5.Remove the screw (C) securing the bracket to the machine.
6.Remove the bracket.
7.Remove the TTM tray 4 media feeder.
Reinstallation note:  When replacing the TTM tray 4 media feeder, ensure that the following parts are removed 
and installed on the new TTM tray 4 media feeder: 
•Rear metal bracket
•TTM tray 4 lower guide
•TTM tray 4 feeder upper guide 

4-228  Service Manual 5058-030  
Go Back Previous
Next
TTM tray 4 media transport removal
1.Pull the TTM tray 4 media tray from the machine.
2.Remove the two screws (A) securing the TTM tray 4 media transport to the machine.
3.Slide the TTM tray 4 media transport out of the machine and remove it. 

Repair information 4-229
  5058-030
Go Back Previous
Next
TTM tray 4 media tray removal
1.Remove the TTM tray 4 media transport. See “TTM tray 4 media transport removal” on page 4-228.
2.Remove the screw (A) securing the lock bracket to the machine.
3.Remove the lock bracket.
4.Gently lift and remove the TTM tray 4 media tray from the machine. 

4-230  Service Manual 5058-030  
Go Back Previous
Next
TTM tray 4 media turn guide removal
1.Open the left door.
2.Gently press the lower edges of the tray module 4 media turn guide.
3.Remove the tray module 4 media turn guide from the machine.
TTM upper transport motor removal
1.Remove the tray module rear cover. See “Tray module rear cover removal” on page 4-215.
2.Disconnect the cable (A).
3.Release the harness from the clamp (B). 

Repair information 4-231
  5058-030
Go Back Previous
Next
4.Remove the two screws (C) securing the TTM upper transport motor to the machine.
5.Remove the TTM upper transport motor. 

4-232  Service Manual 5058-030  
Go Back Previous
Next
Bridge unit removal procedures
Bridge decurler rear cover removal
1.Remove the bridge unit assembly. See “Bridge unit assembly removal” on page 4-236. 
2.Remove the three screws (A) securing the bridge decurler rear cover to the machine.
3.Remove the bridge decurler rear cover. 

Repair information 4-233
  5058-030
Go Back Previous
Next
Bridge decurler right cover removal
1.Remove the bridge unit assembly. See “Bridge unit assembly removal” on page 4-236.
2.Remove the two screws (A) securing the bridge decurler right cover to the machine. 
3.Remove the bridge decurler right cover.
Bridge decurler top cover removal
1.Remove the bridge unit assembly. See “Bridge unit assembly removal” on page 4-236.
2.Remove the bridge decurler rear cover. See “Bridge decurler rear cover removal”...

4-234  Service Manual 5058-030  
Go Back Previous
Next
4.Remove the two screws (A) securing the bridge decurler top cover to the machine.
5.Remove the bridge decurler top cover.
Bridge drive motor removal
1.Remove the bridge unit assembly. See “Bridge unit assembly removal” on page 4-236. 
2.Remove the bridge decurler rear cover. See “Bridge decurler rear cover removal” on page 4-232.
3.Remove the bridge unit right cover. See “Bridge decurler right cover removal” on page 4-233. 
4.Remove the four screws...

Repair information 4-235
  5058-030
Go Back Previous
Next
5.Disconnect the cable (B).
6.Remove the bridge drive motor. 

4-236  Service Manual 5058-030  
Go Back Previous
Next
Bridge unit assembly removal
1. Release the hook securing the bridge unit hookup cover (A) to the finisher.
2. Remove the bridge unit hookup cover (A).
3. Remove the finisher from the printer. 
B
Grounding strapGrounding strap