Lenovo Thinkvision L193p Users Guide

OSD Icon on
Main MenuS ubme nu D e s cription Contro ls  and
Adjus tme nts(Analog) Controls  and
Adjus tme nts (Digital)
Options Menu Position Adjusts menu location on the screen. Same as Analog
Defa ult Re turns the  me nu p o sitio n to  the  d e fa ult se ttings.
C us to m    Ho rizo nta l: C ha nge s the  ho rizo nta l p o s itio n o f the  O S D.    Vertical: Changes the vertical position of the OSD.
   Save
F ac to ry De fa ult    Cancel
   Reset
Resets monitor to the original factory settings....

The display modes shown below have been optimized at the factory.
Table 2-3. Factory set display modes
Addre s s ability R e fre s h rate
640 x 350 70 Hz
640 x 480 60 Hz, 72 Hz, 75 Hz
720 x 400 70 Hz
800 x 600 60 Hz, 72 Hz, 75 Hz
1024 x 768 60 Hz, 70 Hz, 75 Hz
1280 x 1024 60 Hz, 75 Hz
Image rotation
Before rotating the monitor, you should set-up your computer to rotate the image.
Rotating the image may require special rotation software or you may find\
 that your
computer is preloaded with video graphic...

Caring for your monitor
Be sure to turn off the power before you perform any maintenance on the monitor.
Do not:· Apply water or liquid directly to your monitor.
· Use solvents or abrasives.
· Use flammable cleaning materials to clean your monitor or any other elec\
trical
equipment.
· Touch the screen area of your monitor with sharp or abrasive items. This type of
contact may cause permanent damage to your screen.
· Use any cleaner which contains an anti-static solution or similar additi\
ves. This
may...

Detaching the monitor stand
After placing the monitor face down on a clean surface or soft cloth, re\
move the four
screws from the stand to remove it from the monitor.
2-9L193p Flat Panel Monitor User’s Guide
 

Chapter 3. Reference information
This section contains monitor specifications, instructions to manually i\
nstall the
monitor driver, troubleshooting information, and service information.
Monitor specifications
Table 3-1. Monitor specifications for type-model 4431-HB2
Dimensio ns He ightDepth
Wid th378.69 mm (14.91 in.)
240 mm (9.44 in.)408 mm (16.06 in.)
S t a nd Tilt  r a nge R a nge : - 0
0, +300
Swivel Range: -450, +450
Lift Range: 110.0mm
Pivot Yes (clockwise 90 degree)
VESA mount Supported 100 mm...

Table 3-1. Monitor specifications for type-model 4431-HB2 (continued)
3-2
L193p Flat Panel Monitor User’s Guide
C o mmunic a tio ns VES A DDC C I
Supported Display Modes
(VESA Standard modes b etwe e n no te d  ra nge s) Horizontal frequency
Vertical frequency
30 kHz - 81 kHz
56 Hz - 76 Hz
Native Resolution 1280 x 1024 at 60 Hz
Temperature Operating Storage
Shipping10
0 to 350 C (50 to 950 F)
-20
0 to 600 C (-40 to 1400 F)
-20
0 to 600 C (-40 to 1400 F)
Humidity Operating Storage
Shipping10% to 80%
5%...

Proble m Possible  cause Suggested action Refe re nce
The wo rds O ut
o f Ra nge  a re
shown on the
screen, and the power indicator
is fla shing gre e n. The system is set to a
d is p la y mo d e  w hic h is not supported by the
mo nit o r. If yo u a re  re p la c ing a n o ld  mo nito r,
reconnect it and adjust the display
mode to within the specified range
fo r yo ur ne w mo nito r.
If using a Wind o ws  s yste m,  re sta rt
the system in safe mode, then select
a supported display mode for your...

Table 3-2. Troubleshooting (continued)
Manual image setup
If automatic image setup does not establish the image that you prefer, perform
manual image setup.
Note: Have your monitor powered on for about 15 minutes, until the monitor war\
ms
up.
1. Press 
  at the bottom of the monitor to open the OSD menu.
2. Use 
 or  to select  and press  to access.
Pro ble m Po s s ible  ca us e S ugg e s te d action R e fe re nce
Screen is blank and
power
ind ic a t o r  is
steady amber
o r fla s hing green The  mo...

Chapter 3. Reference information3-5
3. Use 
 or  to select 
Clock and Phase  adjustment.
· Clock  (pixel frequency) adjusts the number of pixels scanned by one horizont\
al
sweep. If the frequency is not correct, the screen shows vertical stripe\
s and the
picture does not have the correct width.
· Phase  adjusts the phase of the pixel clock signal. With a wrong phase adjustment,
the picture has horizontal disturbances in light picture.
4. When the image no longer looks distorted, save the Clock and...

3-6L193p Flat Panel Monitor User’s Guide
16. Close all open windows and remove the CD.
17. Restart the system.
Note:On LCD monitors, unlike CRTs, a faster refresh rate does not improve display
quality. Lenovo recommends using either 1280 x 1024 at a refresh rate of 60
Hz, or 640 x 480 at a refresh rate of 60 Hz.
Installing the monitor driver in Windows XP
Note:  This section must be completed before continuing with the Windows XP
automatic image setup.
1. Turn off the computer and all attached devices....