Lenovo Ideapad 110s 11ibr User Guide

							17
Chapter 4. Troubleshooting
Frequently asked questions  
 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -   
This section lists frequently asked questions by category.
 Finding information
What safety precautions should I follow when using my computer?
The Lenovo  Safe
 ty and General Information Guide  which came with your computer contains 
safety precautions for using your computer. Read and follow all the precautions when using 
your computer.
Where can I find the hardware spec ifica
 tions for my computer?
You can find the hardware specification for your  computer 
 on the printed flyers which came 
with your computer.
Where can I find warranty information? For detailed warranty information on this machine, please visit below website to check out: 
support.lenovo.com/warrantystatus.
Drivers and preinstalled software
W

here are the installation discs for Lenovo  preinstalled
  software (desktop software)?
Your computer did not come with installation discs for Lenovo preinstalled software. If you 
ne ed to

 reinstall any preinstalled software, you can find the installation program on the D 
partition of your hard disk. If you cannot find the installation program there, you can also 
download it from the Lenovo consumer support website.
Where can I find drivers for the variou s ha

rdware devices of my computer?
If your computer is preinstalled with a Window s op
 erating system, Lenovo provides drivers for 
all the hardware devices that you need on the D partition of your hard disk. You can also 
download the latest device drivers from the Lenovo consumer support website.
 BIOS setup utility
W

hat is the BIOS setup utility? The BIOS setup utility is a ROM-based software. It  

displays basic computer information and 
provides options for setting boot devices, se curity, hardware mode, and other preferences.
How can I start the BIOS setup utility? To start the BIOS setup utility:
1Shut down the computer.
2Press the Novo button and then select  BIOS Setup.
How can I change the boot mode? There are two boot modes:  UEFI an
 d Legacy Support. To change the boot mode, start the BIOS 
setup utility and set boot mode to  UEFI or Legacy Support  on the boot menu. 
						

							18
Chapter 4. Troubleshooting
When do I need to change the boot mode?The default boot mode for your computer is  UEFI mode
 . If you need to install a legacy operating 
system, such as Windows, Linux or Dos, etc. (tha t is, any operating system before Windows 8) on 
your computer, you must change the boot mode to  Legacy Support. The legacy operating system, 
such as Windows, Linux or Dos, etc. cannot be  installed if you dont change the boot mode.
Getting help
How can I contact the customer support center?
See “Chapter 3. Getting help and service” in the Lenovo  Safety 
 and General Information Guide. 
						

							Chapter 4. Troubleshooting
19
Troubleshooting   - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -  -  - - - - - - - - - - - -   
Display problems
When I turn on the 
computer, nothing 
appears on the screen.•
If the screen is blank, make sure that:
- The AC power adapter is connected to the computer, and p
 lugged into a working electrical outlet.
- The computer power is on. (Press the Power button again  for
  confirmation.)
• If t
hese items are properly set, and the screen remains blank, 
have the computer serviced.
The screen goes blank 
whil
 e the computer is on. •
Your screen saver or power management may be enabled. Do 
one of the following to exit from the screen saver or to 
resume from sleep mode:
- Touch the touchpad.
- Press any key on the keyboard.
- Press the Power button.
-Press  F9 ( 
 ) to confirm whether the backlight of the 
LCD screen has been turned off.
BIOS password problems
I forgot my password. •If you forget your user password, ask the system 
administrator to clear your user password.
• If 
you forget your hard disk drive password, a Lenovo 
authorized servicer cannot reset your password or recover 
data from the hard disk. You must take your computer to a 
Lenovo authorized servicer or a marketing representative to 
have the hard disk drive replaced. Proof of purchase is 
required, and a fee will be charged for parts and service.
• If
 you forget your administrator password, a Lenovo 
authorized servicer cannot reset your password. You must 
take your computer to a Lenovo authorized servicer or a 
marketing representative to have the system board replaced. 
Proof of purchase is required , and a fee will be charged for 
parts and service. 
						

							20
Chapter 4. Troubleshooting
Sleep problems
The critical low-battery 
error message appears, 
and the computer 
immediately turns off.•
The battery power is getting low. Connect the AC power 
adapter to the computer.
The computer enters sleep 
mo
 de immediately after 
Power-on self-test (POST). •
Make sur e that:
- The battery pack is charged.
- The operating temperature is within the acceptable range.  See “Chapt
 er 2. Use and care Information” in the Lenovo 
Safety and General Information Guide .
Note:If the battery pack is charged an d the temperature is within range, have the computer serviced.
The computer does not 
return from sleep mode, 
and the computer does 
not work.•If your computer is in sleep mode, connect the AC power adapter 
to the computer, then press any key or the Power button.
•If the system still does not return from sleep mode, stops 
responding, or cannot be turned off, reset the computer. 
Unsaved data may be lost. To reset the computer, press and 
hold the Power button for four seconds or more. If the 
computer is still not reset, remove the AC power adapter.
Display panel problems
The screen is blank. •Do the following:
- If you are using the AC power adapter or the battery pack, 
and th
 e battery status indicator is on, press  F12 ( 
 ) to 
make the screen brighter.
- If the power indicator is off, press the Power button to  r
 esume from sleep mode.
- If the problem persists, follow the solution in the next  p
 roblem “The screen is unreadable or distorted.”
-Press  F9 ( 
 ) to confirm whether the backlight of the 
LCD screen has been turned off.
The screen is unreadable 
or
  distorted. •
Make sur e that:
- The display device driver is installed correctly.
- The screen resolution and color quality are correctly set.
- The monitor type is correct.
Incorrect characters 
appe
 ar on the screen. •
Is the operating system or programs installed correctly? If 
they are installed and configured correctly, have the 
computer serviced. 
						

							Chapter 4. Troubleshooting
21
Sound problems
No sound can be heard 
from the speaker even 
when the volume is 

turned up.
•Make sure that:
- The Mute function is off.
- The combo audio jack is not being used.
- Speakers are selected as the playback device.
Battery pack problems
Your computer shuts down 
before the battery status 
indicator shows empty.
-or-Your computer operates 
after the battery status 
indicator shows empty.
•Discharge and recharge the battery pack.
The computer does not 
operate with a fully 
charged battery pack.•The surge protector in the battery pack might be active. Turn 
off the computer for one minute to reset the protector; then 
turn on the computer again.
A hard disk drive problem
The hard disk drive does 
not work.•Make sure that the hard disk drive is included in the Boot 
menu in the BIOS setup utility correctly.
A startup problem
The Microsoft® Windows 
operating system does 
not start.
•For details, see “Recovery system” on page 15.
Recovery System problems
Failure to restore system 
partition to factory default.•The system partition (e.g. the partition size or the drive 
capacity of C) has been modified. 
						

							22
Chapter 4. Troubleshooting
Other problems
Your computer does not 
respond.•To turn off your computer, press and hold the Power button 
for four seconds or more. If the computer still does not 
respond, remove the AC power adapter.
•Your computer might lock when it enters sleep mode during 
a communication operation. Disable the sleep timer when 
you are working on the network.
The computer does not 
start from a device you 
want.•See the Boot menu of the BIOS setup utility. Make sure that 
the BIOS setup utility is set so that the computer starts from 
the device you want.
•Also make sure that the device from which the computer 
starts is enabled. Make sure that the device is included in the 
Boot menu in the BIOS setup utility correctly.
•While turned off, press the Novo button to select the device 
you want the computer to start from.
The connected external 
device does not work.•Do not connect or disconnect any external device cables other 
than USB while the computer power is on. Otherwise, you 
might damage your computer.
•When using high power consumption external devices such 
as an external USB optical disk drive, use an external device 
power adapter. Otherwise, the device may not be recognized, 
or the system may shut down as a result. 
						

							23
Trademarks
The following terms are trademarks or registered trademarks of Lenovo in the United States, 
other countries, or both.
Lenovo
ideapad
Microsoft and Windows are trademarks of Microsoft Corporation in the United States, other 
countries, or both.
Other company, products, or service names may be trademarks or service marks of others. 
						

							©Lenovo China 2016
en-US
Rev. AA00