Lawn Mower 92 Cm Cutting Deck For Mountfield 2000 Series Instructions Manual Dutch Version

							
8211-3049-01
BRUKSANVISNINGKÄYTTÖOHJEET
BRUGSANVISNING BRUKSANVISNING
GEBRAUCHSANWEISUNG INSTRUCTIONS FOR USE MODE D’EMPLOI
GEBRUIKSAANWIJZINGISTRUZIONI PER L’USO
INSTRUCCIONES DE USO
INSTRUÇõES DE UTILIZAÇÃO INSTRUKCJA OBS £UGI
»HC“P”K÷»fl œOÀ‹«Œ¬¿“EÀfl NÁVOD K POU ®ITÍ
HASZNÁLATI UTASÍTÁS
NAVODILA ZA UPORABO
92 cm cutting deck
for Mountfield 2000 series 
						

							2
1
A
B
3
5
A+5
A
7
2
4
6
8 
						

							3
9
11
RL
10
L + R12
YZ
X
V
W 
						

							4
ENGLISHGB
SYMBOLS
The following symbols can be found on the 
machine to remind you of the care and attention 
that are required during use.
The symbols mean:
Warning!
Read the instruction manual and the safety 
manual before using the machine.
Warning!
Do not insert your hands or feet under the 
cover when the machine is in operation.
Warning!
Watch out for discarded objects. Keep 
onlookers away.
Warning!
Before starting repair work, remove the 
spark plug cable from the spark plug.
INSTALLATION
DECK ARMS
1. Install the left and right deck arms in the cutting 
deck’s front two corners. Use the existing screw 
and flat washer (fig. 1). Tighten the screw. After 
tightening, it should be possible to move the deck 
arms up and down.
2. Do not hook the rear part of the deck arms onto 
the deck yet (See “Cutting deck” point 7 below).
CUTTING DECK
1. Place the cutting deck in front of the machine. 
Set the maximum cutting height.
2. Remove the locking pin and the outermost flat 
washer from the machine’s steering knuckle.
3. Thread one deck arm onto the steering knuckle. 
Place the flat washer on the steering knuckle and 
secure with the locking pin. Repeat on the other 
side (fig. 2).
4. Force the V-belt onto the machine’s pulley A 
(fig. 3).
5. Lift up the deck’s rear part past the catch until it 
drops down. When the weight of the deck is resting on the upper side of the catch, the installation is 
correct (fig. 4).
6. Tension the belt with belt idler B. The belt idler 
should be on the inside of the belt and pull out to 
the left (viewed from the driver’s position).
7. Screw the lift spring into the machine’s lifting 
arm. (fig. 5). 
SETTING
In order for the deck to cut evenly and attractively, 
it has to be correctly adjusted: 
1. Make sure the air pressure in the tyres is correct:
Front: 0.4 bar (6 psi).
Rear: 1.2 bar (17 psi). 
2. Place the machine on a level floor. Undo the 
screws on either side of the deck (fig. 6). 
3. On the side of the deck arm are four short and 
two long lines. The upper long line (A) is the basic 
setting for a machine with 16” tyres (fig. 7).
Depending on the length of the grass, the deck can 
be adjusted in various ways:
4a. Cutting normal length grass:
Adjust the deck so that the front and rear edge of 
the cover are the same height above the floor. This 
position gives the best Mulch effect, i.e. the grass 
is cut up best.
4b. Cutting long grass:
Adjust the deck so that the cover’s rear edge is 
higher than the front edge. This position means 
that the deck can release the grass more easily at 
the rear edge.
5. After setting, tighten the screws properly. 
USE
CUTTING HEIGHT
The cutting height can be varied between a number 
of fixed positions, from 30 to 85 mm.
Note: Stated cutting heights apply when the 
machine is on a firm surface. 
CUTTING TIPS
For optimum Mulch effect, follow these tips:
- cut frequently.
- run the motor at full revs.
- keep the underside of the cutting deck clean.
- use sharp blades.  
						

							5
ENGLISHGB
- do not cut wet grass.
- cut twice (with different cutting heights) if 
the grass is long. 
SERVICE AND MAINTENANCE
PREPARATIONS
Unless otherwise stated, all service and 
maintenance must be carried out on a stationary 
machine when the motor is not running.
Prevent the machine from rolling by 
always applying the parking brake.
Prevent unintentional starting of the 
motor by always stopping the motor, 
disconnecting the spark plug cable 
from the spark plug and earthing it. 
Disconnect the negative cable from the 
battery. 
LUBRICATION
The deck arms are equipped with grease nipples 
(fig. 8).
Lubricate these after every 25 hours of operation 
(or at least once per season) with universal grease.
MAINTENANCE TIPS
To make cleaning and maintenance easier, the 
cutting deck can be folded up: 
1. Set the cutting height setting to the maximum 
cutting height. 
2. Lift the rear edge of the deck with one hand (fig. 
9). 
3. Push up the catch and release the rear edge of the 
deck (fig. 9).
4. Repeat the procedure on the other side.
5. Secure the tensioning arm on the hook.
6. Force the belt off the machine’s pulley.
7. Fold up the deck to the vertical position (fig. 10).
When the deck is folded down to working position, 
ensure that the catch drops down into position 
when the rear edge of the deck is lifted up (fig. 4).
CLEANING
After each use, the underside of the cutting deck 
should be rinsed off. If the grass has dried solid, scrape clean the 
underside. 
If necessary, paint the underside to prevent 
corrosion.
BLADES
Use protective gloves when changing 
blades to avoid cutting yourself.
Ensure that the blades are always sharp. This 
produces the best cutting results. 
Always check the blades after a collision. If the 
blade system has been damaged, defective parts 
should be replaced.
Always use original spare parts. Non-
original spare parts can entail a risk of 
injury, even if they fit the machine.
Install the blades according to fig. 11 
where the blade edge is marked. The folded-up 
edge of the blade should be positioned inwards 
towards the blade mount. 
The cutting system comprises two blade bars with 
two replaceable blades Y (fig. 12). When replacing 
blades, both should be replaced to avoid 
imbalance.
Install the new blades. Tighten screws V and W 
properly. Tightening torque: V - 9.8 Nm, W - 24 
Nm.
In the event of a powerful collision, the blades may 
be bent out. Undo the locking nut X and fold back 
the blade. Install a new original break bolt V. 
Tighten the locking nuts X and Z.
POSITIVE DRIVE BELT
Both blades are powered inside the deck by a 
positive drive belt. 
If one of the blades has struck a solid object (e.g. a 
stone), the belt tension may be altered. This can 
lead to the positive drive belt ‘over-meshing’ 
which, in the long term, can damage the blades. 
Following a powerful collision, always 
check that both blades are at right-
angles to each other (fig. 11). 
The working areas of the blades overlap each 
other. If the blades’ position in relation to each 
other has been altered, there is a considerable risk 
of the blades striking each other. This can entail  
						

							6
ENGLISHGB
serious damage to the cutting deck.
If this is the case, take the machine and cutting 
deck to a service workshop for repair and 
inspection. 
						

							NOTES
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
.................................................................................................................................................................... 
						

							Manufactured by GGP Sweden AB