Land Rover Rover 214 Repair 1689 12 Rover Manual

1689 Rover 214 & 414 Updated Version 09/97
12
Chapter 12
Body electrical systems
Bulbs (exterior lamps) - renewal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Bulbs (interior lamps) - renewal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Cigar lighter - removal and refitting . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Clock - removal and refitting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Dim-dip headlamp system - operation  . . . . . . . . ....

Fuses
Fuse Rating (amps) Circuit(s) protected
1 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clock, instruments, direction indicators and dim-dip unit
2 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Starter signal
3 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Central locking
4 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

1 General information and
precautions
General information
The electrical system is of the 12-volt
negative earth type and comprises a 12-volt
battery, an alternator with integral voltage
regulator, a starter motor and related
electrical accessories, components and
wiring. The battery is of the maintenance-free
(sealed for life) type and is charged by the
alternator, which is belt-driven from a
crankshaft-mounted pulley.
While some repair procedures are given,
the usual course of action is to renew a...

voltage. Most problems can be traced to a
loose connection. Bear in mind that some
circuits are only live when the ignition switch
is switched to a particular position.
Finding a short circuit
6One method of finding a short circuit is to
remove the fuse and connect a test light or
voltmeter to the fuse terminals with all the
relevant electrical components switched off.
There should be no voltage present in the
circuit. Move the wiring from side to side while
watching the test light. If the bulb lights...

Under no circumstances should this fuse be
removed as this may cause inflation of the
airbag. Refer to your Rover dealer if you think
fuse renewal is necessary.
4To remove a fuse, first switch off the circuit
concerned (or the ignition), then fit the
tweezers and pull the fuse out of its terminals.
Slide the fuse sideways from the tweezers.
The wire within the fuse is clearly visible. If the
fuse is blown, the wire will be broken or
melted.
5Always renew a fuse with one of an
identical rating. Never use...

5Refitting is the reverse of the removal
procedure.
Models with airbag (SRS)
6Remove the ignition key and wait at least
ten minutes to allow the SRS system backup
circuit to fully discharge. Disconnect both
battery leads, earth lead first, to avoid
accidental detonation of the airbag.
7Set the steering in the dead-ahead position
then lock the steering column in its lowest
position. 8Remove the airbag unit.
9Remove the steering wheel, see Chap-
ter 10.
10Remove the five fusebox cover securing
screws and...

22Undo the retaining screws and remove
the switch from the trim panel (see
illustration).
23On refitting tighten the switch screws
securely.
Courtesy lamp switches
24With the door open, undo the two screws
securing the switch to the body. Pull out the
switch and tie a piece of string to the wiring to
prevent it dropping into the body.
25Disconnect the switch and remove it from
the vehicle.
26Refitting is a reverse of removal.
Handbrake warning lamp 
switch
27From inside the vehicle, carefully prise out...

release it from the rear of the lamp (see
illustration).
4Withdraw the bulb.
5When handling a new bulb, use a tissue or
clean cloth to avoid touching the glass with
the fingers. Moisture and grease from the skin
can cause blackening and rapid failure of this
type of bulb.
6Refitting is the reverse of the removal
procedure. Ensure that the new bulbs locating
tabs are correctly located in the lamp cutouts.
Front sidelamp
7Working in the engine compartment, twistoff the large circular plastic cover and...

from the top of the lamp body to gain access
to the bulb.
24The bulb is of the capless (push fit) type
and can be pulled out of the lamp unit.
25Refitting is a reverse of the removal
procedure.
6 Bulbs (interior lamps)-
renewal
2
General
1Refer to Section 5.
Courtesy lamps
2Carefully prise the lens off the lamp unit
then remove the festoon bulb from its end
contacts.
3Fit the new bulb using a reversal of the
removal procedure. Check the tension of the
spring contacts and if necessary, bend them
so that...

13All bulbs, with the exception of the main
panel illumination bulb, are integral with their
holders. The main panel illumination bulb is of
the capless type and is a push fit in its holder
(see illustrations). Be very careful to ensure
that the new bulbs are of the same rating as
those removed as this is especially important
in the case of the ignition/battery charging
warning lamp.
14Refitting is the reverse of the removal
procedure.
Facia illumination bulbs
15To renew the various facia illumination...