Land Rover Range Rover On Board Telephone Lm 2nd Edition Rover Manual

							Charges
40
Ch arge sShowing time and cost of last call
NOTE: Details shown in this section, Charges, 
assumes compatability with the network 
provider.
•   Call up the main menu.
•Select ‘TIMER CHARGE 6’ and confirm.
•Select ‘Last Call’ and confirm.
Display shows:
‘Last Call 02:00 Min 1.36GBP
(GBP = Great Britain Pounds)
•Select ‘OK’ to switch to the next higher level 
menu.
The display shows:
The duration of the last call.
The charges for the last call, assuming that the 
charge rate has been set (see determining the 
charge rate later in this section of the Handbook).
The number of units used, if your service 
provider supports this feature.
All cost/charges are a network-dependent 
service.
Showing time and cost of all calls
•   Call up the main menu.
•Select ‘TIMER CHARGE 6’ and confirm.
•Select ‘All Calls’ and confirm.
Display shows:
‘All Calls 20:00 Min 13.60GBP
•Select ‘OK’ to switch to the next higher level 
menu.
The display shows:
The duration of all calls.
The charges for all calls, assuming that the 
charge rate has been set (see determining the 
charge rate later in this section of the Handbook).
The number of units used, if the network 
operator supports this feature.
Resetting call duration and call charges
A SIM card that permits input of a PIN2 can be 
used to reset the duration of a call and the call 
charges.
•   Call up the main menu.
•Select ‘TIMER CHARGE 6’ and confirm.
•Select ‘All Calls’ and confirm.
Display shows:
‘All Calls 20:00 Min 13.60GBP
•Select ‘REJECT’ to reset the values to 0.
You are now requested to enter PIN2.
The display shows:
‘Enter PIN2’
Enter PIN2 (your code).
The display shows:
‘****’
Select ‘OK’
The values for the total call duration and the total 
charges are reset to 0.
Activating automatic charge display
If you wish to have the duration and charges 
incurred displayed automatically after every call:
•   Call up the main menu.
•Select ‘TIMER CHARGE 6’ and confirm.
•Select ‘AutoCharge Disp’ and confirm.
Display shows:
‘Autocharge Disp Off’
•Select ‘ALTER’
Display shows:
‘Autocharge Disp 

On’.
•Select ‘OK’.
The display shows:
‘

Autocharge Disp’.
Perform a similar operation to switch off the 
automatic charge display. 
						

							41
Charges
Switching on the 1 minute bleep
To hear a reminder signal every minute during a 
call:
•   Call up the main menu.
•Select ‘TIMER CHARGE 6’ and confirm.
•Select ‘1 Minute Bleep’ and confirm.
Display shows:
‘1Minute Bleep Off’
•Select ‘ALTER’
Display shows:
‘1 Minute Bleep

On’.
•Select ‘OK’.
The display shows:
‘

1 Minute Bleep’.
Perform a similar operation to switch off the 1 
minute bleep.
CHARGE LIMIT
A SIM card that permits input of a PIN2 can be 
set to permit use of only a predefined number of 
charge units. This restriction can only be 
determined, altered or cancelled with PIN2.
Activating and adjusting charge limit
•   Call up the main menu.
•Select ‘TIMER CHARGE 6’ and confirm.
•Select ‘Charge Limit’ and confirm.
Display shows:
‘Charge Limit Off’
•Select ‘ALTER’
Display shows:
‘Enter PIN2’.
•Enter PIN2 (your code).
•Select ‘OK’
Display shows:
‘Charge Limit 0 Units.
•   Select to delete the existing value.
•Enter new charge limit.
Display shows:
‘Charge Limit 100 Units’.•Select ‘OK’. The charge limit is now set to 100 
units.
To interrupt input, select ‘BACK’.
The option ‘BACK’ does not appear in the display 
until the new entry has been deleted completely.
The previous value is then retained.
Deactivating charge limit
•   Call up the main menu.
•Select ‘TIMER CHARGE 6’ and confirm.
•Select ‘Charge Limit’ and confirm.
Display shows:
‘Charge Limit 

On’
•Select ‘ALTER’
Display shows:
‘Enter PIN2’.
•Enter PIN2 (your code).
•Select ‘OK’
Display shows:
‘Charge Limit 123 Units’.
•   Select to delete the existing value.
•Enter new charge limit., e.g. 0
Display shows:
‘Charge Limit 0 Units’.
•Select ‘OK’ to store a new value
The limit is now set to 0 charge units; the limit is 
now deactivated. 
						

							Charges
42
Cancelling input
•Select ‘BACK’.
The option ‘BACK’ does not appear in the display 
until the new entry has been deleted completely.
The previous value is then retained.
CHARGE RATE
If your service provider transmits information on 
charges and you are registered for this service, 
after every call you will receive details of the 
number of charge units used.
You can enter the charge rate per unit as 
specified in your contract. The phone then 
calculates the cost of the call and displays it. If 
the number of units is not transmitted, you will 
only receive information on the call duration.
You can also enter the charge per minute. In this 
instance, the calculated costs may not be very 
precise.
NOTE: Charge rate is a network-specific feature.
Determining the charge rate
•   Call up the main menu.
•Select ‘TIMER CHARGE 6’ and confirm.
•Select ‘Charge Rate’ and confirm.
Display shows:
‘Per Unit:0.68 Per Min:1.00 Currency GBP’
•Select ‘ALTER’
Display shows:
‘Enter PIN2’.
•Enter PIN2 (your code).
•Select ‘OK’ to confirm the input.
You can now set the charge rate.
Altering the charge per unit
•Display shows:
‘Per Unit:0.68
•   Select to delete the existing value.
Enter new value.
Select ‘OK’ to store the input.
You can now alter the charge per minute.
Altering the charge per minute
•Display shows:
‘Per Min:1.00’
•   Select to delete the existing value.
Enter new value.
Select ‘OK’ to store the input.
You can now select the currency.
Selecting currency
•Display shows:
‘GBP’ 
•   Select to delete the existing entry.
Select new currency.
Select ‘OK’ to store the input.
You can now select the currency.
Cancelling input
•Select ‘BACK’.
The option ‘BACK’ does not appear in the display 
until you have deleted the complete entry. The 
previous value is retained. 
						

							43
System Settings
Use r Co nfigura tion
System SettingsLANGUAGE
Adjusting display language
• Call up the main menu.
•Select ‘SETTINGS 7’ and confirm.
•Select ‘Language’ and confirm.
All available languages are listed in the 
display.
•Select required language, e.g ‘English’ and 
confirm.
Display shows:
‘

English’.
The display texts will now appear in English.
KEY SETTINGS
Switching on key lock
• Call up the main menu.
•Select ‘LOCAL SETTINGS 8’ and confirm.
•Select ‘Keys’ and confirm.
•Select ‘Key Lock’ and confirm.
 is shown in the display, in the 
stand-by mode.
The key lock is now switched on.
   You can also switch on the key lock by 
pressing and holding this key.
NOTE: Even with the key lock switched on, it is 
possible to receive calls or make an emergency 
call.
Cancelling key lock
   Press and hold.
Switching on key acknowledge
• Call up the main menu.
•Select ‘LOCAL SETTINGS 8’ and confirm.
•Select ‘Keys’ and confirm.
•Select ‘Key Acknowledge’ and confirm.
•Select ‘Key Sound’ and confirm.
Display shows:
‘

Key Sound’
•   Set using the key.
The key lock is now switched on.
Switching off key acknowledge
• Call up the main menu.
•Select ‘LOCAL SETTINGS 8’ and confirm.
•Select ‘Keys’ and confirm.
•Select ‘Key Acknowledge’ and confirm.
•Select ‘Key Silent’ and confirm.
Display shows:
‘

Key Silent’
•   Set using the key.
The key lock is now switched off. 
						

							System Settings
44
Answering a call with any key
If you wish to answer incoming calls with any key 
on the handset:
• Call up the main menu.
•Select ‘LOCAL SETTINGS 8’ and confirm.
•Select ‘Any Key Answer’ and confirm.
Display shows:
‘Any Key Answer Off’.
•Select ‘ALTER’.
Display shows:
‘Any Key Answer 

On’.
•Select ‘OK’.
Display shows:
‘

Any Key Answer’.
Any key can now be pressed to accept a call.
Perform a similar operation to switch off the 
function.
EQUIPMENT SETTINGS
Switching on illuminated display
• Call up the main menu.
•Select ‘LOCAL SETTINGS 8’ and confirm.
•Select ‘Display’ and confirm.
•Select ‘Lighting’ and confirm.
Display shows:
‘Lighting Off’.
•Select ‘ALTER’.
Display shows:
‘Lighting 

On’
•Select ‘ON’.
Display shows:
‘

Lighting’.
Perform a similar operation to switch off the 
display lighting.
To maximise the stand-by time before the 
batteries require recharging, switch off the 
lighting.
Entering greeting text
• Call up the main menu.
•Select ‘LOCAL SETTINGS 8’ and confirm.
•Select ‘Display’ and confirm.
•Select ‘Greeting Text’ and confirm.
•You are now requested to enter text
Display shows:
‘Greeting: ’.
•Enter, for example, ‘Hello’ with the keypad.
Display shows:
‘Greeting: Hello’.
Select ‘OK’ to store the text and switch to the 
higher level menu.
The greeting appears in the display for a few 
seconds each time the mobile device is switched 
on.
Altering the greeting text
• Call up the main menu.
•Select ‘LOCAL SETTINGS 8’ and confirm.
•Select ‘Display’ and confirm.
•Select ‘Greeting Text’ and confirm.
•The display now shows the previous text
‘Greeting: Hello’.
•   Select to delete the text.
Enter new text with the keypad.
The display shows the new text.
Select ‘OK’ to store the text and switch to the 
higher level menu. 
						

							45
System Settings
Adjusting the switch-off timer
You can determine how long the car phone 
remains on stand-by after you have parked the 
vehicle, to protect the vehicle battery against 
being drained. The maximum value that can be 
set is 120 minutes.
• Call up the main menu.
•Select ‘SETTINGS 7’ and confirm.
•Select ‘Airtime Remain’ and confirm.
The current value set is shown in the display.
•   Select to delete the existing value.
•Enter a new value e.g.90.
• Select ‘OK’.
The stand-by time is now set to 90 minutes, that 
is, the phone will remain on stand-by for 90 
minutes after the vehicle ignition is turned off.
Activating EjectBox answering
If you would like to answer a call simply by taking 
the handset out of its cradle:
• Call up the main menu.
•Select ‘LOCAL SETTINGS 8’ and confirm.
•Select ‘EjectBox Answer’ and confirm.
Display shows:
‘EjectBox Answer Off’.
•Select ‘ALTER’.
Display shows:
‘EjectBox Answer 

On’.
•Select ‘OK’.
Display shows:
‘

EjectBox Answer’.
   It is now no longer necessary to press this 
key in order to answer a call.
Perform a similar operation to switch off 
EjectBox answering.
Resetting the handset
If you wish to cancel any modified settings on the 
handset and restore the manufacturer’s settings:
• Call up the main menu.
•Select ‘LOCAL SETTINGS 8’ and confirm.
•Select ‘Status’ and confirm.
•Select ‘Standard Value’ and confirm.
•Select ‘Mobile unit’ and confirm.
The handset settings are now reset to the 
standard values.
   Press to interrupt without saving. 
Any previously modified settings remain valid. 
						

							System Settings
46
Resetting the base station
To reset any previously modified settings on the 
handset to the manufacturer’s settings:
• Call up the main menu.
•Select ‘LOCAL SETTINGS 8’ and confirm.
•Select ‘Status’ and confirm.
•Select ‘Standard Value’ and confirm.
•Select ‘Base’ and confirm.
The base station settings are now reset to the 
standard values.
   Press to interrupt without saving.
Any previously modified settings remain valid.
Displaying phone ID number
• Call up the main menu.
•Select ‘LOCAL SETTINGS 8’ and confirm.
•Select ‘Status’ and confirm.
•Select ‘Phone Info’ and confirm.
The phone ID number is shown in the display.
Select ‘OK’ and switch to the next higher level 
menu.
NOTE: This is also known as the IMEI number 
and may be requested by the service provider.
WARNING
Do NOT log off the handset.
If you log off the handset and later wish to log 
back on, you will need to visit a Land Rover 
dealership to register the handset again.
RINGING TONES
Switching on call tone
• Call up the main menu.
•Select ‘TONES 1’ and confirm.
•Select ‘Call Tone’ and confirm.
To switch off call tone, select ‘Off’ and confirm.
Selecting ‘Beep’ as the ringing tone
If you want to select just a simple signal as the 
ringing tone.
• Call up the main menu.
•Select ‘TONES 1’ and confirm.
•Select ‘Call Tone’ and confirm.
•Select ‘Beep’ and confirm.
Display shows:
‘

Beep’.
Adjusting the ringing tone sound
You can choose from 16 pitches for the sound of 
the ringing tone. The currently selected tone 
pitch is heard as a reference. The volume may 
not be set to the value ‘0’.
• Call up the main menu.
•Select ‘TONES 1’ and confirm.
•Select ‘Sound’ and confirm.
Select the desired pitch with the display/rocker 
keys and confirm with ‘OK’ to store the setting.
Adjusting the ringing tone volume
The volume of the ringing tone can be adjusted in 
6 stages. The current volume is heard as a 
reference during adjusting.
• Call up the main menu.
•Select ‘TONES 1’ and confirm.
•Select ‘Volume’ and confirm.
Adjust the volume with the display/rocker keys 
for display control
or
Adjust the keys on the side of the handset.
Select ‘OK’ to store the setting. 
						

							47
System Settings
SERVICE SIGNALS
Switching on service signals
You can set your phone to emit special service 
signals when it establishes a connection with the 
network and after a number has been dialled.
• Call up the main menu.
•Select ‘SETTINGS 7’ and confirm.
•Select ‘Special Tones’ and confirm.
•Select ‘Service Signals’ and confirm.
Display shows;
‘Service Signals Off’.
•Select ‘ALTER’.
Display shows;
‘Service Signals 

On’.
•Select ‘OK’ and switch to the next higher 
menu level.
Display shows;
‘

Service Signals’.
Perform a similar operation to switch off the 
service signals.
CONTROL TONES
The warning signal indicating that the handset 
battery is almost discharged and the signal to 
indicate out of range cannot be switched off. 
						

							System Settings
48
STANDARD SETTINGS
Base unit
The standard settings of the car phone base 
station as supplied by the manufacturer.
These values above are set by activating the function ‘Base Unit standards settings’.
The following settings are not affected by the function ‘Base Unit standards settings’.
FunctionStandard settings
Ringing tone. On.
Number of call cycles before automatic answering. 3.
Automatic charge display. Off.
Automatic answering. Off.
CB signal. On.
DTMF touchtone. On.
Prevent new SIM. Off.
Duration of last call. 0.
Charge limit. Off.
Charge rate per minute. 0.
Duration of all calls. 0.
All calls incognito. Off.
Next call incognito. Off.
1 minute beep. Off.
Stand-by time. 1 minute.
Language. English.
Phone book sorting. Alphabetically.
TOP 8 list sorting. Alphabetically.
Loan phone. Off. 
						

							49
System Settings
Handset
The standard settings of the car phone base 
station as supplied by the manufacturer.
FunctionStandard setting
Call waiting. On.
Greeting text. None.
Lighting. On.
EjectBox answering. Off.
Any key answer. Off.
Sound of call tone. Level 5.
Volume of receiver. Level 3.
Volume of tone call. Level 3.
Key lock. Off.
Service signals. Off.
Key acknowledge. On.