Land Rover Range Rover In Car Entertainment 3rd Edition Rover Manual

							Caring for Compact Discs
19 IMPORTANT
Use standard 12cm CDs only.
DO NOT use irregularly shaped or
damaged CDs - these may damage
the compact disc changer.
8cm CD singles must NOT be used,
even if a CD adaptor is fitted.
The CD autochanger should not be
used in temperatures outside the
range -10
°C to +60°C.
If the CD autochanger overheats,’CD
OVER TEMP’will be displayed -
change to radio or tape mode until
the unit has cooled.
The CD autochanger should only be
used as described - any other
application or method of use could
result in the user being exposed to
invisible laser radiation exceeding the
limit of laser class 1.
NOTE:Additional magazines can be
obtained from a Land Rover dealer.CARING FOR COMPACT DISCS
Dirt, dust, condensation and heat can
damage discs. Always observe the following
precautions:
NEVERtouch the horizontal playing surface
(the unlabelled side) of a disc! Handle discs
by holding the outer edges, or the edge of
the central hole and the outer edge, between
finger and thumb.
ALWAYSreturn discs to their boxes after use
(dirt detracts from the sound quality).
NEVERleave the disc or the box exposed to
excessive heat or direct sunlight!
NEVERuse a solvent or abrasive cleaner!
Dust or dirt should be removed from the
playing surface by wiping with a clean, dry,
lint-free cloth always wipe in a straight line
from the centre to the edge of the disc! 
						

							Security Code
20
SECURITY CODE INFORMATION
To reduce the risk of theft, Range Rover
radio/cassette and CD players are
programmed with a four digit security code.
Once activated, this code prevents the unit
from functioning if it is illegally removed
from the vehicle. There are 10,000 different
codes - making your radio equipment
valueless to a thief unless he has the correct
one. In addition, each unit is further
protected by a time delay penalty system that
effectively defies even the most systematic
attempt to break the code.
NOTE:If an incorrect code is entered, a one
minute time delay is imposed before a
second code can be attempted. Each time a
wrong code is entered, the time delay
doubles (2 min, 4 min, 8 min, etc.) making
theft a very unattractive proposition.
The vehicle was supplied with a Security
Information card. This card contains a record
of the four digit security code, as well as the
unit’s unique serial number. The serial
number is also stamped into the metal side
of the unit and, in the event of theft, would
confirm proof of ownership.
It is VERY IMPORTANT that you keep a safe
record of the security code and heed the
following advice:
NEVER keep a record of the security code
in the vehicle.
PLEASE stick the security warning
stickers where the potential thief is sure
to see them, but where they do not
impede your vision of traffic and
pedestrians.
If you lose your code number, contact the
nearest Land Rover dealer, who will be
able to obtain this information for you.Activating the code
Your dealer will have correctly activated the
security code before you took delivery of the
vehicle. This is confirmed whenever you
switch the unit on by’CODE’appearing
BRIEFLY in the display.
If this display is absent, the radio will still
work, but will not be protected by the
security code. If this is the case, you should
activate the code by keeping the’up’tuning
button depressed while turning the set on (a
two-tone bleep will sound). Before activating
the code, ensure that you have the Security
Information card with the security code on it. 
						

							Security Code
21
ICE0106
ENTERING THE SECURITY CODE
If the code has not already been entered, or
power to the set has been interrupted, the
code MUST be entered before the set will
operate. Enter the code as follows:
Switch on the radio (’CODE’appears in
the display). Press pre-set button 1.
Press either the up or down tuning button
(highlighted in illustration) until the first
digit of the security code appears in the
display. Press pre-set 1 to store the first
digit in the unit’s memory.
Use either tuning button to select the
second digit of the code (correct digit
appears in the display). Press pre-set 1 to
store the second digit.
Select the third digit, again using the
tuning buttons (until the correct digit is
displayed). Press pre-set 1 to store the
third digit.
Select the final digit (the display now
shows the full four digit code). Press
pre-set 1 to store the final digit.If the correct code has been selected, a
two-tone bleep sounds and the radio will
operate.
NOTE:If an incorrect code has been entered,
the first time delay period commences.
During the delay period,’WAIT’appears in
the display - DO NOT switch off. At the end
of the delay period,’CODE’reappears in the
display and you can then enter the correct
code. Remember; the time delay period
doubles each time an incorrect code is
entered.