Land Rover Range Rover Audio Tv Navigation System Lm Aus Rover Manual

							58
Off-Road Navigation
Compass
The red compass arrow always points to True 
North (to an accuracy of ±15°). True North is the 
basis from which heading and bearing readings 
are calculated.
Heading
The heading is the direction in which the vehicle 
is pointing. The navigation computer and GPS 
satellite receiver work in conjunction to calculate 
the difference in degrees (°) between the vehicles 
direction and True North - this is the reading 
displayed.
Heading Up icon
This indicates the direction in which the direction 
arrow should be pointing to follow the shortest 
route (by distance) to the destination or next 
waypoint. The icon will remain at the top of the 
compass part of the guidance display.
Bearing
The bearing is the direction (as the crow flies) to 
the destination or next waypoint. The bearing is 
calculated in degrees (°) from True North.
Altitude
The altitude reading is accurate to within 150 
feet. If a valid reading is not available, the last 
known altitude will be shown. 
						

							59
Television
Television
TELEVISION CONTROLS
2. Display
7. MENU button
Press to obtain the general menu and also to 
return to the menu from a system feature.
8. Right rotary control
Turn to select a menu item, press to confirm 
selection.
H47568
2
7 
						

							60
Television
TV INTRODUCTION 
Up to 10 TV stations can be stored manually or 
automatically. Picture format and TV format can 
be adjusted to suit individual requirements and 
teletext can be used to display the latest news 
and information.
NOTE: For occupant safety, the TV picture is only 
displayed with the vehicle stationary and the 
handbrake applied.
SELECTING TV
Press the MENU button (7) on the control panel 
to display the menu.
•Turn the control to select ‘Television’.
•Press the control to confirm selection.
Searching for a station
•Turn the right rotary control (8) to select 
‘Search’.
•Press the control to confirm selection.•Turn the control again to start the station 
search.
Station search is halted when a station with a 
sufficiently strong signal is located on a 
reception channel.
If reception quality deteriorates, a search 
procedure starts automatically. If the word 
‘Mute’ appears on the screen, this indicates that 
the TV sound has been automatically 
suppressed.
Trial view and selection
You can display all the memorised stations 
briefly and then select one.
•Turn the right rotary control (8) to select 
‘Programme’.
•Press the control and hold in for about 
1 second.
•Press the control again to continue viewing 
the displayed stations.
Storing stations manually
You can allocate stations to any presets you 
wish:
•Turn the right rotary control (8) to select 
‘Search’. 
•Press the control to confirm selection.
•Turn the control again to start station search. 
Station search is halted when a station with a 
sufficiently strong signal is located.
•Press the control again and hold in for about 
1 second.
MENU
On Road Navigation
On-board computer
Aux heat/vent
Set
DSP
Monitor off
Code
Off Road Navigation
Television
TMC30.07.200114:10Monday
H4758
Search ProgrammeCH 40
24
Set
Teletext
 
Display Zoom 
21 -30Autostore
H4165
Search ProgrammeCH 40
24
Set
Teletext
 
Display Zoom 
Hold key to store channel
H4167 
						

							61
Television
•Turn the control until the desired memory 
position between 1 and 30 is displayed.
•Press the control to store the selection.
Storing stations automatically
•Turn the right rotary control (8) or press until 
the TV menu is displayed.
•Turn the control to select ‘Autostore’.
•Press the control again to start an automatic 
station search with memorising.
If the inputs are not made within 4 seconds, this 
process will have to be repeated.
The first 10 stations are stored in memory 
locations 21 - 30.
Selecting a stored station
The station stored in memory location 21 is 
automatically shown when TV is selected.
To select a different memorised station:
•Turn the right rotary control (8) or press until 
the TV menu is displayed.
•Turn the control again to select ‘Programme’.
•Press the control again to confirm selection.
•Turn the control until the desired station is 
tuned.
Selecting TV format
Not all countries use the same TV format. 
However, you can adapt your unit to accept the 
format of the country in which you are driving.
(PAL, SECAM, NTSC)
•Turn the right rotary control (8) or press until 
the TV menu is displayed.
•Turn the control again to select ‘Set’.
•Press the control again to confirm selection.
•Turn the control to select ‘TV format’.
Search
Programme
CH 40
24
21 -30
Set
Teletext
 
Display Zoom 
Autostore
H4168
Search ProgrammeCH 40
CH 43
24
21 -30
Set
Autostore
Teletext 
Display 
H4163
Search
Programme
CH 40
CH 43
24
21 -30
Set
Autostore
Teletext 
Display 
H4164 
						

							62
Television
•Press the control to confirm selection.
•Turn the control to select the country in which 
you are currently travelling from the list 
displayed.
•Press the control to confirm/exit.
ADJUSTING THE TV SCREEN
Adjusting contrast, brightness and colour
•Turn the right rotary control (8) to select ‘Set’.
•Press the control to confirm selection.
•Turn the control again to select the desired 
control.
•Press the control again to confirm selection.•Turn the control to alter the setting.
•Press the control to confirm/exit.
Adjusting picture format
•Turn the right rotary control (8) or press until 
the TV menu is displayed.
•Turn the control again to select ‘Display’.
•Press the control again to confirm selection.
•Turn the control to select the desired picture 
format:
4:3
16:9
Zoom - proportional enlargement.
•Press the control to confirm/exit.
Contrast
H4275
returnTV-FormatEnglandColourBrightness
H4276
TV-FormatEngland
Contrast
H4234
returnTV-FormatEnglandColourBrightness
Search ProgrammeCH 40
24
21 -30
Set
Autostore
Teletext Display Zoom 
H4169 
						

							63
Television
Selecting Teletext
•Press the MENU button (7) on the control 
panel.
•Turn the right rotary control (8) to select 
‘Television’.
•Press the control to confirm selection.
•Turn the control again or press until the TV 
menu is displayed.
•Turn the control to select ‘Teletext’.
•Press the control to view teletext.
If the inputs are not made within four seconds, 
this process will have to be repeated.
Selecting information
Turn the right rotary control (8) until the desired 
page number appears at the top left.
The page will be located and displayed. 
Subsequent pages will be displayed 
automatically if the information extends over one 
page.
Suppressing next page
If the information occupies more than one page, 
the signal to move onto the next page comes 
from the transmitter. You can suppress it as 
follows:
•Press the right rotary control (8) to enter the 
teletext menu.
•Turn the control to select ‘Hold’.
•Press the control again to confirm selection.
Search ProgrammeCH 40
24
21 -30
Set
Autostore
Teletext 
Display Zoom 
H4170
CHILL OUT AND GET ON THE SLOPES   226SKI DEALS  Take a  look:ITV WEST MIDLANDS
Ski holidays           226
Holiday index           200
TELETEXT SHOWCASE   105NEW Mobile Ring Tone Service p35
at our selection of
ski offers and head for
the pistes this winter
100
TELETEXT
Teletext 100 Oct1911:21:12
H4256
Hold TV 
Zoom  Page 
H4172 
						

							64
Television
Enlarging text
•Press the right rotary control (8) to enter the 
teletext menu.
•Turn the control to select ‘Zoom’.
•Press the control again to confirm selection.
•To enlarge the text, press the control: 
once to enlarge the upper half of the screen 
display
twice to enlarge the lower half of the screen 
display.
•To see the complete screen display again, 
press the control for a second time.
To quit teletext
•Press the right rotary control (8) to enter the 
teletext menu.
•Turn the control to select ‘TV’.
•Press the control again to return to TV 
reception. 
						

							65
System Settings
System SettingsSYSTEM SETTINGS
Altering the system settings
Your vehicle is delivered with a basic setting for 
all displays, which depends upon the country for 
which the vehicle is intended.
These settings can be altered to suit your 
preferences.
Press the MENU button on the control panel to 
display the general menu screen.
•Turn the right rotary control (8) until ‘Set’ is 
highlighted.
•Press the control to obtain a list of possible 
settings.
You can alter:
•The language of the display texts,
•The units of measurement for distance, fuel 
consumption and temperature,
•The time and date
and the way these are expressed.The following can also be changed by turning the 
control further:
1. Memo
Shortly before the hour, three signal tones 
will be emitted. If you have switched on this 
function, you will see a soundwave symbol 
at the bottom edge of the display screen, 
after the day.
2. Audio + OBC
Means radio and on-board computer 
displays appear on the screen at the same 
time.
1. On-board computer display
You can choose whether to have the outside 
temperature or your estimated time of 
arrival displayed.
2. Colour set
Means you select a set of colours for the 
display screen from the three options 
available.
3. Day/night
Means you can switch the automatic 
day/night changeover function for colour 
set on or off.
MENU
On Road Navigation
On-board computer
Aux heat/vent
Set
DSP
Monitor off
Code
Off Road Navigation
Television
TMC30.07.200114:10Monday
H4759
Temp Consumpt.Distance
Audio+OBCClock
Date
SET
TMC
30.07.200114:10
SW   3 - 1 / 10
Language
Memo
C1/100km Km
on
24 h
dd.mm GB
on
oF o
milesF
mphKm/l
12 h set
off
mm.dd set
off
Monday
H4122 
						

							66
System Settings
To change the date
For an example, changing the date is used to 
illustrate how to alter a system setting.
•Turn the right rotary control (8) until ‘Date’ is 
highlighted.
•Press the control to confirm this.
•Turn until ‘set’ is highlighted.
•Press to start the adjustment procedure.
•Turn the control to adjust the year.
•Press to store.
•In the same way, set the month and weekday.
The date entry is memorised with your last save.
You can also choose the order in which you wish 
the date to be displayed; either the days (dd) first 
followed by the months (mm) or in the opposite 
order.
Temp Consumpt.Distance
Audio+OBCClock
Date
SET
TMC
30.07.200114:10
SW   3 - 1 / 10
Language
Memo
C1/100km Km
on
24 h
dd.mm GB
on
oF o
milesF
mphKm/l
12 h set
off
mm.dd set
off
Monday
H4123
Temp Consumpt.DistanceDATE
Audio+OBCClock
Date
SET
TMC
30.07.200114:10
SW   3 - 1 / 10
Language
Memo
on
24 h
dd.mmon12 h set
off
mm.dd set
off
Monday
12/01/01
H4124 
						

							67
Troubleshooting
T ro ubles hoo tingWHAT TO DO IF....
Radio
What to do if:
•The radio automatically begins a station 
search with RDS switched on?
The strength of the station transmitting has 
decreased and no alternative frequency for 
this station is available.
The radio reverts to the frequency of the station 
previously received.
Cassette
What to do if:
•The quality of audio reproduction from 
cassettes deteriorates?
The tape head may be dirty and requires 
cleaning.
•The display shows ‘TAPE CLEAN’
This message appears twice in succession 
when a cassette is inserted after 50 hours of 
operation.
•The display shows ‘TAPE ERROR’.
The tape in the cassette player will not move 
or is jammed. Remove the cassette from the 
tape player. If you are able to identify the 
cause of the problem and put it right, you may 
put the cassette back into the tape drive and 
then wind it fully forwards or fully rewind. If 
the message is still displayed, the cassette 
should not be used.
CD
What to do if one of the following warnings is 
displayed:
•‘NO DISKS’
the magazine is empty.
•‘NO DISK’
no CD in the compartment or a CD has been 
inserted incorrectly.
•‘NO MAGAZINE’
no magazine is inserted.•‘CD CHECK’
the contents of the CD are still being read into 
the system.
•‘HIGH TEMP’
operating temperature is too high. replay 
commences automatically when the correct 
operating temperature has been reached.
Navigation
What to do if:
•You call-up your vehicle current position but 
the display is not accurate?
You are in a poor reception area, you are in an 
area not covered by the map, or the system is 
currently calculating your position..
•The GPS logo disappears from the screen?
Reception is interrupted; a building or similar 
obstruction may be the cause.
•An address from the destination list is not 
transferred to the route guidance 
programme?
The address is not on the map CD currently in 
use. Choose an address as close as possible 
to the original one, if necessary by the graphic 
destination input method.
•An address without a street is not transferred 
to the destination guidance programme?
There is no defined city centre on the map CD 
for the place that you have entered. Enter any 
street or a specific destination, such as the 
railway station, for the town or city in 
question. Then start destination guidance.
•You wish to input a destination address but 
the correct letter of the alphabet cannot be 
selected?
The addess is not on the map CD currently in 
use. In this case the system will not offer you 
the non-existent letters to choose from. 
Choose an address as close as possible to the 
original one, if necessary by the graphic input 
method.