Land Rover Iidtool For Discovery 3 Britpart Manual

							P11
IIDTool
5. Activating the IIDTool
To activate the IIDTool, you will need access to the exact vehicle it will be used on. Once your activation 
code is noted, you will need an internet connection to get your unlock code.
1.  Ensure that the vehicle is in Park (or in Neutral with the handbrake applied for manual transaxle) 
and in a safe environment.  
 
 Turn the key to the ON position.
The OBD connector is located at the bottom 
dash panel above and outside the brake 
pedal on the driver’s side of the vehicle.
GAP Diagnostic 7/15/2014 All right reserved
User manual: Version 8, Firmware V3.0
Land Rover Discovery 3/LR3, Range Rover Sport 2004-2009
    
						

							P12
IIDTool
  Using the integrated interface
2.  Connect the IIDTool and wait until the message «IIDTool Ready» appears on your instrument 
display. If the Bluetooth interface is to be used, connect the mobile device to the tool 
(see page P9 for connecting instructions). You can now call up the IIDTool by pressing the 
Resume / Enter button for 2 seconds.  
3.  Navigate to the following submenu : IIDTool Menu->IIDTool Confi g->Enter Unlock Code
4.  Take note of the 10 characters code, go to our website and follow the instructions to retrieve 
your unlock code. Both the activation and unlock codes are in hexadecimal format: 0 to 9 and A 
to F.
 http://www.GAP-diagnostic.com/support/unlock.html
5.  Go back to the vehicle and follow steps 1. to 4. Press Resume / Enter once more and enter the 
unlock code using the Speed + / Menu up and Speed - / Menu down buttons to change cha-
racters and Resume / Enter to go to the next character. If you make a mistake, exit the IIDTool 
menu with the On-Off / Back button and re-enter the menu with a 2 sec. press / hold of the 
Resume / Enter button.
GAP Diagnostic 7/15/2014 All right reserved
User manual: Version 8, Firmware V3.0
Land Rover Discovery 3/LR3, Range Rover Sport 2004-2009 
						

							P13
IIDTool
 
 
Using the mobile App
To proceed with the following steps, your mobile device will have to be connected on the internet. If not 
possible, you will have to fi ll up the form on our website using another device connected to the internet. 
1.  Ensure that the vehicle is in Park and in a safe environment. 
2.  Connect the IIDTool on the vehicles OBD port.
3.  Wait a few seconds and connect the IIDTool 
Pro on the mobile device.  
4.  Press on «Activate» to display the activation page:
5.  If you have not yet created an account on our website, press on Register. Else, press on LogIn 
to log on our website and proceed with step 7 by returning to the App. You can also register 
directly on our website using another device connected on the internet.
6.  Complete the registration process and return to the App to Log In.
7. Press on Activate, fi ll up the blanks on the website form and press Submit. If your mobile 
device is not connected to the internet, note the 10 character code and on our website, 
click on My GAP->Activate My Product after you have logged in. In both cases, the unlock 
code will be sent to you by e-mail.
8.  Once you have received the unlock code by e-mail, enter it in the Enter Unlock fi eld of the App 
and press on Unlock.
. 
GAP Diagnostic 7/15/2014 All right reserved
User manual: Version 8, Firmware V3.0
Land Rover Discovery 3/LR3, Range Rover Sport 2004-2009 
						

							P14
IIDTool
Once the unlock code is entered correctly, the IIDTool will backup the original suspension calibration 
and CCF content. Confi rmation messages will appear and the unit will enter the menu.
•  Once your IIDTool is activated, please proceed with updating the fi rmware to the latest 
version. Instructions on how to update your tool can be found on the page P7.
•  You can enable the enhanced functions on additional vehicles by purchasing additional VIN 
licenses from a Britpart dealer. Once you have your new license(s), connect the IIDTool to a 
new vehicle and follow the procedure above to activate the IIDTool. When you access the GAP 
Diagnostic website to receive your unlock code you will be asked to enter your new VIN license 
as well.
•  When unlocked on a vehicle, the IIDTool does an automatic backup of the vehicle’s height set-
tings and vehicles confi gurations. For details about the backup procedure, please consult the 
Save/Restore section of this manual. 
•  You can also unlock your IIDTool for future vehicles before connecting the unit to these particu-
lar vehicles. Please consult the Save Restore section of this manual for more details.
GAP Diagnostic 7/15/2014 All right reserved
User manual: Version 8, Firmware V3.0
Land Rover Discovery 3/LR3, Range Rover Sport 2004-2009 
						

							1
IIDTool
Contents, for
Land Rover Discovery 3/LR3, Range Rover Sport 2004-2009
II. Using the IIDTool D3-2
III. Menu tree D3-5
IV.  Main Menu Options D3-6
V.  Vehicle control modules software updates Defi nitions D3-SU-1
VI. Service Test Routine Defi nitions D3-SR-1
VII. Limited Warranty W1
D3- GAP Diagnostic 7/15/2014 All right reserved
User manual: Version 8, Firmware V3.0
Land Rover Discovery 3/LR3, Range Rover Sport 2004-2009 
						

							2
IIDTool
II. Using the IIDTool
 Integrated Interface
Your IIDTool needs no additional cables or power supply. 
GAP Diagnostic 7/15/2014 All right reserved
User manual: Version 8, Firmware V3.0
Land Rover Discovery 3/LR3, Range Rover Sport 2004-2009D3-
The IIDTool is controlled with the vehicle’s cruise control 
switchgear. 
The functions are:
1.  Speed +  = Menu up / increase value
2.  Speed -   = Menu down / decrease value
3.  Resume  = Enter*
4.  On-Off     = Back one level / Exit
*When viewing a confi guration in the car confi guration menu, 
pressing the Resume button will show the next available 
option for this confi guration.
 
 
   
   
   
   
   
    
						

							3
IIDTool
Information is displayed on the instrument cluster message center. Due to limited space, longer mes-
sages such as error codes are scrolled through automatically. 
 
   
  
 
Note: When the following symbol is displayed , the IIDTool will continue the current process after 
the Speed + / Menu up button is pressed.
D3- GAP Diagnostic 7/15/2014 All right reserved
User manual: Version 8, Firmware V3.0
Land Rover Discovery 3/LR3, Range Rover Sport 2004-2009 
						

							4
IIDTool
 Use
1.  Ensure that the vehicle is in Park (or in Neutral with the handbrake applied for manual transaxle) 
and in a safe environment.  
 
   
•    If the vehicle is outside, start the engine.
•    If in a garage, Turn the key to the ON position. 
•    If you plan to use the device for more than 10 minutes with the engine not running, connect 
a power supply (Midtronic’s PSC-550 or equivalent) to the vehicle’s battery. 
 Note: Battery chargers are not suitable due to poor line regulation.
2.  Wait until no more warning messages are displayed on the instrument cluster. Connect the 
IIDTool and wait until the message «IIDTool Ready» appears on your instrument display. If the 
Bluetooth interface is to be used, connect the mobile device to the tool (see page P9 for 
connecting instructions). You can now call up the IIDTool by pressing Resume / Enter for 2 
seconds.  
3.  Navigate the menu by using the Resume / Enter button to enter, the On-Off / Back button to 
exit or go back, and the Speed + / Menu up and Speed - / Menu down buttons to navigate up or 
down or change values.
4.  To exit the IIDTool menu use the On-Off / Back button to navigate to the top level menu and 
press  On-Off / Back again or move the vehicle*. The message “Exiting Menu” confi rms that the 
session is terminated. The IIDTool can be disconnected anytime except when re-fl ashing  an 
ECU or performing a CCF write.
   
 *Except while viewing a live value. Please read Section 7 Live Values for more details.
Remove the IIDTool from the OBD connector when done!
Additional Information’s
  First use ECU scan
Upon fi rst use on a vehicle, the IIDTool will scan the vehicle and note the presence of all ECU’s on 
communications buses. The resulting list is stored in the IIDTool memory for up to 20 vehicles. 
 
WARNING
Upon entering, some functions will display warning messages. 
The fi rst time these functions are used, the warnings messages 
will be displayed 3 times and cannot be skipped. When these 
functions are used again later, a press of the Resume / Enter 
button skips the warning message.
By pressing the Resume / Enter button, the user confi rms that 
he has read and understood the warnings.
Note: The majority of functions will work with both the key to the ON position or with the engine running. 
Here is a list of functions that won’t work if the engine is running. The key must be in the ON position.
•   Clear fault of the RCM-Airbag ECU.
•   Clear fault of the BCM-Body Control ECU.
•   Service Reminder Reset.
GAP Diagnostic 7/15/2014 All right reserved
User manual: Version 8, Firmware V3.0
Land Rover Discovery 3/LR3, Range Rover Sport 2004-2009D3- 
						

							5
IIDTool
III. Menu tree 
GAP Diagnostic 7/15/2014 All right reserved
User manual: Version 8, Firmware V3.0
Land Rover Discovery 3/LR3, Range Rover Sport 2004-2009
D3- 
						

							6
IIDTool
IV. Main Menu Options
1.  Read fault
 
Defi nition
When an abnormal situation or behavior is detected by an ECU, it registers a fault code that can be 
accessed by a diagnostic tool. To view faults currently stored in any ECU, select the Read Fault option 
in the top level menu and press Resume / Enter to enter.
 
  Checking for faults using the Select ECU function
The ECU list will now be displayed. The menu is navigated up and down with the Speed + / Menu up 
and Speed - / Menu down buttons. Choose an ECU to be checked and press Resume / Enter to enter. 
If there are no faults stored in the ECU’s memory, the message ‘No Fault Stored’ will appear and the 
IIDTool will automatically go back to the ECU selection menu.
  Checking for faults using the Scan ECU function
The IIDTool will proceed with scanning each ECU to see if there are faults stored in memory. Once 
fi nished, only the ones with at least one fault stored will be displayed in the list. The menu is navigated 
up and down with the Speed + / Menu up and Speed - / Menu down buttons. Choose an ECU to be 
checked and press Resume / Enter to enter.
Note: The IIDTool does not enter the ECU list at the bottom – you can scroll both up AND down from 
the starting point. The list is not in alphabetical order.
 
GAP Diagnostic 7/15/2014 All right reserved
User manual: Version 8, Firmware V3.0
Land Rover Discovery 3/LR3, Range Rover Sport 2004-2009D3-