Land Rover Discovery Series Ii In Car Entertainment Nas Rover Manual

							Radio Tuning
9
RADIO PRE-SET BUTTONS
The six pre-set buttons (7) can be used to
manually store up to twelve FM stations (six
each on FM1 and FM2) and twelve AM
stations (six each on AM1 and AM2). The
pre-sets are programmed as follows:
Programming the pre-sets
·Select the required waveband (FM1, FM2,
AM1 or AM2).
·Tune to the desired frequency using
either automatic or manual tuning.
·Press and hold one of the pre-set buttons
until a bleep sounds. The frequency is
now stored (the display shows the
waveband and frequency or name of the
station to which you have tuned).
NOTE:Once the pre-sets have been
programmed, they will be retained by the
unit until they are re-programmed or until the
battery is disconnected.
Operating the pre-sets
Once the pre-set buttons have been
programmed, operation is simple; select the
desired waveband, then press the pre-set
button of your choice.
734ICE0083
AUTO-STORE
Auto-store enables you to rapidly tune and
store the strongest FM and AM radio signals
in a single operation. This facility is
particularly useful if you are in an unfamiliar
area and have little knowledge of local
transmitter frequencies.
Programming auto-store
Press and hold the appropriate waveband
selection button (3 or 4) until a bleep sounds
(the radio mutes and the display shows
either FM AUTOSTORE or AM
AUTOSTORE).
Auto-store scans the waveband to find the
six strongest frequencies and then stores
them on either the FM2 or AM2 pre-set
buttons in order of signal strength.
NOTE:Auto-store overwrites any stations
already stored on the FM2 or AM2 pre-set
buttons.
Radio play resumes when the operation is
complete.
NOTE:If auto-store is unable to find six
strong stations, the remaining pre-set
buttons remain blank.
Operating auto-store
To tune to one of the auto-store frequencies,
select FM2 or MW2, then press the pre-set
button of your choice; the frequency or radio
station name appears on the display. 
						

							Radio Data System
10
RADIO DATA SYSTEM (RDS)
This radio is equipped with RDS (Radio Data
System). RDS operates on the FM waveband
and enables the radio to receive other
information in addition to radio signals,
including:
·the programme service name(this
enables the set to display the radio
station name instead of the frequency).
·programme type selection(allows choice
of listening by one of 15 programme
types rather than by radio station name).
·an alarm announcement system(this
enables the set to give priority to
emergency information; eg. a very
serious accident or natural disaster). All
other audio functions will be overridden
(ALERT appears in the display).Receiving RDS stations
The radio is automatically in the RDS mode
whenever the FM waveband is selected.
Whenever an RDS radio station is received,
the radio station name illuminates in the
display.
NOTE:Not all FM radio stations broadcast
RDS. If a non-RDS station is received the
RDS features described previously will not be
available.
Local radio stations
Reception of most local radio stations is
intentionally limited to a comparatively small
area around the transmitter. 
						

							Programme Type
11
95ICE0111
PROGRAMME TYPE (PTY)
PTY is a service whereby RDS compatible
radio stations are able to transmit a signal
which identifies the programme content.
Your radio is able to receive and decipher
this signal, thereby enabling you to select a
programme category, which will then be
given priority over other broadcasts.
For example, if you want to listen to classical
music, select the CLASSICAL category and
the set will automatically search for and
broadcast a station transmitting the
CLASSICAL PTY code.
Operating PTY
Select your chosen PTY category as follows:
·Press the Programme type button (9); the
current PTY category will appear in the
display (eg. COUNTRY).
·To change the category, scroll up or
down through the list of 22 options using
the tuning buttons (5).
·Press the Programme type button again -
the radio will search through the
waveband for a station broadcasting the
selected PTY code.In some circumstances (depending on the
time of day, popularity of programme choice,
etc), the set may not be able to immediately
locate a radio station broadcasting the
chosen PTY code - the display will show NO
PTY and return to the original station.
The 22 categories available for selection are
as follows.
1.NEWS
2.INFORM
3.SPORTS
4.TALK
5.ROCK
6.CLASSIC ROCK
7.ADULT HIT
8.SOFT ROCK
9.TOP 40
10.COUNTRY
11.OLDIES
12.SOFT
13.NOSTALGIA
14.JAZZ
15.CLASSICAL
16.R & B
17.SOFT R&B
18.LANGUAGE
19.REL MUSIC - (religious music)
20.REL TALK - (religious talk)
21.PERSONALITY
22.PUBLIC 
						

							Headphone Controls
12
H2563
MODE
1
3
2
4
HEADPHONE CONTROLS
The rear passenger headphone controls only
operate with the radio/cassette player
switched on. Plug the headphones into the
socket (arrowed in illustration) to activate the
controls - bass response from the vehicle
speakers reduces and the headphone
symbol, along with a symbol indicating the
current headphone unit mode, appears in the
display.
NOTE:To override the drop in bass response,
press and hold the on/off volume control on
the radio/cassette player.
NOTE:Only headphones compatible with a
3.5 mm jack plug socket can be used. To
obtain optimum sound quality, use
headphones with a resistance of 16 Ohms.
1. Volume controls
Press the +/- buttons to increase/reduce
headphone volume output.
2. Mode control
If a tape and CDs have been loaded, press
the control to change between cassette, CD
and radio play back.
NOTE:Changing mode using the headphone
control unit does NOT effect the audio output
for the rest of the vehicle.3. Auto search controls
The auto search controls has no effect if the
headphone control unit is in the same mode
as the radio/cassette player. For example; if
the radio/cassette player AND the headphone
unit are both in tape mode, the control does
not operate.
During radio play:
Press the appropriate button to search up or
down the selected waveband to locate the
next or previous radio station.
During tape play:
Press the appropriate button to skip to the
beginning of the next, or current track. Press
repeatedly to search through more than one
track.
During CD play:
Press the appropriate button to skip to the
beginning of the next, or current track.
Press and hold the button to search through
more than one track on the currently selected
CD. The search stops when the button is
released.
4. Selection button
The selection button has no effect if the
headphone control unit is in the same mode
as the radio/cassette player.
During radio play:
Press to select the next pre-set station on the
current waveband.
During tape play:
Press to reverse the direction of play.
During CD play:
Press to select the next CD in the
autochanger. 
						

							Radio Reception
13
Distortion, interference and lack of signal
clarity, are often attributed to a fault in the
radio - this is rarely the case.
Problems of this kind are usually caused by
phenomena such as atmospheric conditions,
signal strength, hilly terrain, tall buildings,
bridges and even electrical interference from
power lines.
Please remember:A car radio receives
signals while the vehicle is in motion (unlike
a domestic set) - constantly changing
direction and moving away from, or nearer
to, the transmitter whilst negotiating terrain
with widely differing reception
characteristics. Some interference is to be
expected from time to time.
FM transmitters can only broadcast over a
limited range and good, clear signals will
only be received in the immediate area of the
transmitter. When travelling, it may benecessary to re-tune the radio from time to
time, to offset the effects of moving from
one transmitter area to another.
The broadcast range for good stereo
reception (usually within a 30 to 40 mile
radius of the transmitter) is noticeably less
than it is for mono.
FM Signals (like light waves) travel in a
straight line, so large obstacles, such as tall
buildings, can shield the car from the signal
causing distortion or loss of reception
(known as dead spots).
Distortion can also occur if FM signals
received directly from the transmitter mix
with signals which have been reflected by
obstructions such as mountains, hills and tall
buildings (this is known as multi-path
distortion).
ICE 0052  
						

							Care of Cassette Player and Tapes
14 ICE 0054
Use only good quality tapes with a maximum
capacity of ninety minutes (C90). Check that
both spools rotate freely and remove any
loose turns at the start of the tape by winding
one spool with a pen or pencil.
Cassette player
In use, the tape head accumulates dust and
contamination, gradually impairing sound
reproduction and, in extreme cases, reducing
volume too. To combat contamination, clean
the tape head periodically (after
approximately every 20 hours playing time)
by passing a wet type cleaning cassette
through the player.
NOTE:Because your cassette player is fitted
with auto reverse, the cleaning cassette must
be played in both directions.
The tape will require more frequent cleaning
in winter, as contamination is greater in
conditions of low temperature and increased
humidity. However, the use of good quality
tapes, keeps the build up to a minimum.Cassette tapes
·Always store cassettes in their boxes
when not in use.
·Never leave cassettes in the vehicle
during extremes of temperature. In
particular, do not leave tapes in direct
sunlight as they may warp and become
unuseable, or jam the tape player
mechanism.
·Fast forward, or rewind tapes every 8 to
10 plays to prevent them from becoming
too tightly wound.
·Ensure that labels attached to the cassette
are glued firmly in place.
·DO NOT leave tapes in the cassette player
for more than a few hours in very cold or
humid conditions - the oxides on the tape
surface may contaminate the cassette
player mechanism.
NOTE:After continuous playing, cassettes
may become hot to touch. This is normal
and will not harm good quality tape. 
						

							CD Autochanger & Discs
15
ICE0096231
COMPACT DISC CHANGER UNIT (if fitted)
The CD autochanger is located under the
right hand front seat. The flap at the front of
the seat pedestal allows access to insert and
remove magazines.
Removing/inserting the magazine
Fully open the sliding cover (1) to insert or
remove the magazine. Keep the cover closed
at all other times to prevent dust and dirt
from entering the changer unit.
Press the button (2) to eject the magazine.
Insert the magazine (3) in the direction of the
arrow marked on the magazine casing and
push it fully into the changer. Finally, close
the sliding cover.
ICE0097
3
Loading & unloading the magazine
Holding the magazine as shown (arrow
uppermost), remove each CD tray in turn.
Place a disc (label side uppermost) onto
each tray - holding ONLY the outside edge
and centre hole of the disc. Load only one
disc in each tray. Correctly align the tray with
the parallel slots on each side of the
magazine and slide the tray into the
magazine.
To unload the magazine, hold the magazine
with the arrow uppermost, pull out each tray
in turn, holding the tray securely so as not to
drop the disc. Unload one disc at a time and
handle only the edge and centre of the disc.
ICE0043 
						

							Caring for Compact Discs
16 IMPORTANT
·Use standard 12cm CDs only.
·DO NOT use irregularly shaped or
damaged CDs - these may damage
the compact disc changer.
·8cm CD singles must NOT be used,
even if a CD adaptor is fitted.
·The CD autochanger should not be
used in temperatures outside the
range -10
°Cto+60°C.
·In the unlikely event that the CD
autochanger overheats, CD OVER
TEMP will be displayed - change to
radio or tape mode until the unit has
cooled.
·The CD autochanger should only be
used as described - any other
application or method of use could
result in the user being exposed to
invisible laser radiation exceeding the
limit of laser class 1.
NOTE:Additional magazines can be
obtained from a Land Rover dealer.CARING FOR COMPACT DISCS
Dirt, dust, condensation and heat can
damage discs. Always observe the following
precautions:
NEVERtouch the horizontal playing surface
(the unlabelled side) of a disc! Handle discs
by holding the outer edges, or the edge of
the central hole and the outer edge, between
finger and thumb.
ALWAYSreturn discs to their boxes after use
(dirt detracts from the sound quality).
NEVERleave the disc or the box exposed to
excessive heat or direct sunlight!
NEVERuse a solvent or abrasive cleaner!
Dust or dirt should be removed from the
playing surface by wiping with a clean, dry,
lint-free cloth always wipe in a straight line
from the centre to the edge of the disc! 
						

							Security Code
17
SECURITY CODE INFORMATION
NOTE:Your vehicle was delivered with the
security code disabled, if you wish to have
the code activated, consult your Land Rover
dealer.
To reduce the risk of theft, Discovery
radio/cassette and CD players are
programmed with a four digit security code.
Once activated, this code prevents the unit
from functioning if it is illegally removed
from the vehicle. There are 10,000 different
codes - making your radio equipment
valueless to a thief unless he has the correct
one. In addition, each unit is further
protected by a time delay penalty system that
effectively defies even the most systematic
attempt to break the code.
NOTE:If an incorrect code is entered, a one
minute time delay is imposed before a
second code can be attempted. Each time a
wrong code is entered, the time delay
doubles (2 min, 4 min, 8 min, etc.) making
theft a very unattractive proposition.
The vehicle was supplied with a Security
Information card. This card contains a record
of the four digit security code, as well as the
units unique serial number. The serial
number is also stamped into the metal side
of the unit and, in the event of theft, would
confirm proof of ownership.It is VERY IMPORTANT that you keep a safe
record of the security code and heed the
following advice:
·NEVER keep a record of the security code
in the vehicle.
·PLEASE stick the security warning
stickers where the potential thief is sure
to see them, but where they do not
impede your vision of traffic and
pedestrians.
·If you lose your code number, contact the
nearest Land Rover dealer, who will be
able to obtain this information for you. 
						

							Security Code
18
ICE0085
ENTERING THE SECURITY CODE
If the code has not already been entered, or
power to the set has been interrupted, the
code MUST be entered before the set will
operate. Enter the code as follows:
·Switch on the radio (CODE appears in
the display). Press pre-set button 1.
·Press either the up or down tuning button
(highlighted in illustration) until the first
digit of the security code appears in the
display. Press pre-set 1 to store the first
digit in the units memory.
·Use either tuning button to select the
second digit of the code (correct digit
appears in the display). Press pre-set 1 to
store the second digit.
·Select the third digit, again using the
tuning buttons (until the correct digit is
displayed). Press pre-set 1 to store the
third digit.
·Select the final digit (the display now
shows the full four digit code). Press
pre-set 1 to store the final digit.
If the correct code has been selected, a
two-tone bleep sounds and the radio will
operate.
NOTE:If an incorrect code has been entered,
the first time delay period commences.
During the delay period, WAIT appears in
the display - DO NOT switch off. At the end
of the delay period, CODE reappears in the
display and you can then enter the correct
code. Remember; the time delay period
doubles each time an incorrect code is
entered.