Land Rover Discovery Series Ii 01my In Car Entertainment Nas Rover Manual

R980 - Cassette Player

14. Tape reverse
Press to play the opposite side of the tape.
15. Dolby B noise reduction†
Press when playing tapes recorded using the 
Dolby B NR system (display shows the double ‘D’ 
symbol).
16. Tape scan button
Press the SCAN button to listen to the first 10 
seconds of each track on the tape (both sides). 
The display shows ‘TAPE SCAN’. The scan 
continues until the button is pressed again or 
until another function is selected.
†Noise reduction manufactured under license....


R980 - Compact Disc Player
C ompa ct Disc  Play er
COMPACT DISC PLAYER CONTROLS*
17. CD mode selectorPress to select CD player mode. Playback starts 
from the point on the disc at which play last 
stopped, or from the start of the first disc if the 
magazine is newly inserted. The display shows 
disc number (‘CD1’) and track number (‘01’). If 
no magazine has been inserted into the 
autochanger, ‘NO MAGAZINE’ is displayed.
At the end of each disc, playback automatically 
continues with the next disc...

R980 - Radio Tuning

Rad io  Tu ningRADIO TUNING
Manual tuning
If you know the frequency of the radio station you 
are seeking, or you need to select a radio station 
that is too weak to be found by automatic tuning, 
use manual tuning, as follows:
Select the desired waveband (FM or AM), then 
press the ‘MAN ’ button (6). By briefly pressing 
either tuning button (5), the frequency changes 
(either up or down) in steps of 0.1 MHz for FM, 
or 1 kHz for AM. 
Fast manual tuningBy keeping either tuning...


R980 - Radio Tuning
RADIO PRE-SET BUTTONS
The six pre-set buttons (7) can be used to 
manually store up to twelve FM stations (six each 
on FM1 and FM2) and twelve AM stations (six 
each on AM1 and AM2).The pre-sets are 
programmed as follows:
Programming the pre-sets
•Select the required waveband (FM1, FM2, 
AM1 or AM2).
•Tune to the desired frequency using either 
automatic or manual tuning.
•Press and hold one of the pre-set buttons 
until a bleep sounds. The frequency is now 
stored (the display...

R990 - Radio
	
 R99 0 Au dio Sy stemRadio
SOUND CONTROLS
1. On/off and volume control
Press to switch on (display shows ‘LAND 
ROVER’). Press again to switch off.
Rotate steadily to right or left to adjust the 
volume. Note that turning the control rapidly has 
no effect!
The volume can also be adjusted using the 
remote switches on the steering wheel (see 
‘Owners handbook’).
NOTE: If you have a car telephone with a mute 
signal output connected to the stereo system, 
radio, tape or CD play...



R990 - Radio
Balance: 
Press three times then rotate volume control to 
left or right to adjust balance between left and 
right speakers. Display shows:
•‘BAL R9’ = max sound from RIGHT
•‘BAL 0’ = equal balance
•‘BAL L9’ = max sound from LEFT
Fader: 
Press four times then rotate volume control to 
left or right to adjust balance between front and 
rear speakers. Display shows:
•‘FAD F9’ = max sound from FRONT
•‘FAD 0’ = equal balance
•‘FAD R9’ = max sound from REAR
Press the button again to return to...

R990 - Radio


RADIO CONTROLS
3. FM waveband selector
Press briefly to select FM frequencies. There are 
two FM bands (FM1 and FM2). Both have the 
same tuning range, and each one can be used to 
store six frequencies on the pre-set buttons.
Press and hold to activate auto-store (on FM2 
only - see ‘AUTO-STORE’, page 21). 
4. AM waveband selectorPress briefly to select one of the three AM bands 
(AM1, AM2 and WB). Both AM wavebands can 
be used to store six stations on the pre-set 
buttons. For more...


R990 - Cassette Player
C as sette Play er
CASSETTE PLAYER CONTROLS
10. Tape mode selector
Press to select tape play (display shows ‘SIDE-1’ 
or ‘SIDE-2’).
If the set is switched off during tape play, the 
cassette remains in stand-by mode. Play 
resumes when the set is switched on again.
11. Cassette compartmentInsert the tape with the open side to the right and 
push in gently. The radio mutes and tape play 
starts immediately.
NOTE: At the end of either side of the tape, play 
will automatically...

R990 - Cassette Player

14. Tape reverse
Press to play the opposite side of the tape.
15. Dolby B noise reduction†
Press when playing tapes recorded using the 
Dolby B NR system (display shows the double ‘D’ 
symbol).
16. Tape scan button
Press the SCAN button to listen to the first 10 
seconds of each track on the tape (both sides). 
The display shows ‘TAPE SCAN’. The scan 
continues until the button is pressed again or 
until another function is selected.
†Noise reduction manufactured under license....


R990 - Compact Disc Player
C ompa ct Disc  Play er
COMPACT DISC PLAYER CONTROLS*
17. CD mode selectorPress to select CD player mode. Playback starts 
from the point on the disc at which play last 
stopped, or from the start of the first disc if the 
magazine is newly inserted. The display shows 
disc number (‘CD1’) and track number (‘01’). If 
no magazine has been inserted into the 
autochanger, ‘NO MAGAZINE’ is displayed.
At the end of each disc, playback automatically 
continues with the next disc...