Land Rover Discovery Ii Valeo Bcu Ecu Manual

 
 Single point entry: Single point entry is a function that allows the driver to unlock just 
the drivers door, thus leaving all the other doors in a locked state. It is an option that can 
be enabled using this setting. To use single point entry, press the unlock button on the 
remote transmitter once. Depressing the unlock button a second time in the space of one 
minute unlocks the remaining doors. Single point entry is also possible by turning the key 
in the drivers door lock to the unlock...

 
 Low battery warning: If this setting is set to enabled, the BCU will alert the driver of 
the vehicle if the remote transmitter battery requires replacing. The remote transmitter 
measures its battery voltage and when the voltage goes below a threshold it will transmit 
a special code to the BCU to request that it informs the driver by flashing the LED on-
off-on short flashes of 50mS and off for 2000mS. This is conditional upon the drivers 
door being open and the ignition in an off position, or the...

 
 Alarm sounder: Depending upon the build specification of a vehicle it may have one of 
a small choice of sounders available for audible notification of events by the alarm. This 
setting allows the alarm sounder option to be configured to accommodate any of the fitted 
options either on their own or in conjunction with any other fitted sounder. The sounders 
which can be used are: 
 Battery backed sounder (BBS), located inside the exterior body panel near the 
fuel release solenoid, is a warning...

LED will follow flash rate 2. When the BCU receives an unlock signal (this indicates that 
the security system has been activated), the LED will follow flash rate 2 until the ignition 
is next turned to position II. The LED will flash one longer period if the EKA code 
sequence is started. 
 Passive immobile: When enabled with this setting, passive immobilization prevents the 
vehicle from being started unless a correctly programmed remote transmitter key is used 
to start the vehicle. This system works...

sending a signal to tell the other sensor that it is currently active. When the BCU provides 
power to both sensors, the first to operate sends a 5mS pulse along the signal wire to 
indicate that it has activated. After a period of 458mS the first sensor will switch off. The 
other sensor will, after a delay of 42mS, start to detect movement within the vehicle and 
also send the 5mS signal to declare that it is active along the signal wire. If one of the 
sensors detects movement when it is activated, it...

 
 EKA option: This setting allows configuration of the EKA facility and how its usage 
effects the central locking. Available options are: 
 EKA (emergency key access) is DISABLED. 
 EKA (emergency key access) is enabled and the door locks operate electrically 
(ENABLED). 
 EKA (emergency key access) is enabled, but the door locks do not operate 
electrically (NO UNLOCK). 
 Cruise control: This option is used if Cruise Control is fitted to the vehicle. 
 Air conditioning: This option is used if...

 
INFO 
 
 Serial No: This shows the serial number allocated to BCU. 
 Date: This shows the date of the BCU. 
 Hardware No: This shows the hardware number of the BCU. 
 Software No: This shows the software number of the BCU. 
 Alarm Type: This shows the version number allocated to the alarm specification of the 
BCU. The value is usually 10 but may be different in some countries, altering this 
number does not change the functionality of the alarm. 
 VIN: The vehicles VIN number, the first 3 digits...

 
WASH WIPE 
 Front wiper enable 
 Tail wiper enable 
 Head lamp power wash 
 
HEATED SCREEN 
 Heated screen 
 Heat. Rear screen lamp 
CHECK ENGINE 
 Check engine lamp 
 
OUTPUTS - SECURITY 
Security 
 Horn 
 BBUS ALL 
 BBUS ST 
 Fuel flap 
 Alarm LED 
 Ignition interlock 
 Crank Enable 
 Volumetric power 
 Robust immo. 
 Transponder Power 
LOCKING 
 Lock 
 Unlock 
 Superlock 
 Single point entry 
 
 
 
 
 
 
  

 
 
 
 
KEY PROGRAM 6 DIGIT INNER CODE (Used on the Nanocom Evolution Mk 2) 
 
This function allows you to program one or more keys on the 4 slots available (the suspension 
plip is not used) by means of the 6 digit code printed on the label of the circuit inside the fob. 
The code must be written in the desired slot and confirmed with the corresponding button. We 
suggest using the first slot available. Once the code is inserted and confirmed the SYNC KEY 
function is required to synchronize the fob’s...

If the odometer error setting is enabled in the settings section the display will also flash when the 
BCU odometer value is different to the IP (instrument pack) odometer value.  
 
EKA CODE - READ - SET 
This is a four digit code, each digit of the EKA code can be between 1 and 16.