Kyocera FS C5300DN User Manual

Machine Parts 1-1
1 Machine Parts
This chapter provides explanations and illustrations for you to 
determine the parts and their functions. Try to be familiar with 
the names and functions of these parts for correct use and 
optimal performance.
This chapter contains explanations on the following topics:
Components at the Front of the Printer 1-2
Components at the Left of the Printer 1-2
Internal Components 1-3
Components at the Rear of the Printer 1-3
Operation Panel 1-4
Downloaded From...

1-2Machine Parts 
Components at the Front of the Printer
1 Operation Panel
2 Front Cover
3 Paper Stopper
4 Top Cover (Top Tray)
5 MP (Multi-Purpose) Tray
6 Paper Cassette
7 Power Switch
Components at the Left of the Printer
8 Left Cover
9 Waste Toner Box
10 Main Charger Units on the Drum Units
11 Magenta Toner Container (M)
12 Cyan Toner Container (C)
13 Yellow Toner Container (Y)
14 Black Toner Container (K)
2
5
613
7
4
8
9 10
11 12 13 14
Downloaded From ManualsPrinter.com Manuals 

Machine Parts 1-3
Internal Components
15 Paper Transfer Unit
16 Paper Ramp
17 Duplex Unit
18 Envelope Switch
Components at the Rear of the Printer
19 USB Memory Slot
20 Power Cord Connector
21 Option Interface Slot
22 Network Indicators
23 Network Interface Connector
24 USB Interface Connector
25 Rear Cover
18
19
2021 2223
24
25
15
17
16
Downloaded From ManualsPrinter.com Manuals 

1-4Machine Parts 
Operation Panel
26 Message Display
27 Ready Indicator
28 Data Indicator
29 Attention Indicator
30 Arrow Keys
31 [MENU] Key
32 [OK] Key
33 [GO] Key
34 [Cancel] Key
26 27 28
2930 31
3233 34
Downloaded From ManualsPrinter.com Manuals 

Printing Operation 2-1
2 Printing Operation
This chapter contains explanations on the following topics:
Changing Network Interface Parameters 2-2
Printing a Network Interface Status Page 2-10
Installing the Printer Driver 2-11
Printing from Application Software 2-17
Downloaded From ManualsPrinter.com Manuals 

2-2Printing Operation 
Changing Network Interface Parameters
This printer supports TCP/IP, TCP/IP (IPv6), NetWare, AppleTalk, IPP, 
SSL Server, IPSec protocols and Security Level. (For details refer to 
Advanced Operation Guide.)
TCP/IP, TCP/IP (IPv6) settings
1Press [MENU].
2Press U or V repeatedly until Network > appears.
3Press Z. Each time you press U or V, the selection changes. Refer 
to the explanations below when specifying the settings.
Set this item to On when you connect to a network using...

Printing Operation 2-3
TCP/IP
This section describes how to enable the TCP/IP protocol. 
1If TCP/IP is set to Off, use U or V to select On and press [OK].
2Press Z. Each time you press U or V, the selection changes.
3Display the item you want to set and press [OK]. A blinking question 
mark (?) appears while you are setting DHCP and Bonjour. A 
blinking cursor (_) appears while you are setting IP Address, 
Subnet Mask and Gateway.
4Press U or V to select On or Off as the setting for DHCP and 
Bonjour....

2-4Printing Operation 
TCP/IP (IPv6)
This section describes how to enable the TCP/IP (IPv6) protocol.
1If TCP/IP (IPv6) is set to Off, use U or V to selecto On and press  
[OK].
2Press Z. Each time you press U or V, the selection changes.
3Display the item you want to set and press [OK]. A blinking question 
mark (?) appears while you are setting RA(Stateless) and 
DHCPv6.
4Press U or V to select On or Off as the setting for RA(Stateless) 
and DHCPv6.
5Press [OK].
6Press [MENU]. The display returns to...

Printing Operation 2-5
3Press Z. Each time you press U or V, the selection changes. Refer 
to the explanations below when specifying the settings.
If you are using NetWare, AppleTalk, IPP, SSL Server or IPSec 
to connect to a network, you must enter an administrator ID. By 
default, the administrator ID is the numeric part of your printers model 
name. If you use FS-C5300DN, enter 5300. 
If you are using NetWare, AppleTalk, IPP, SSL Server or IPSec 
to connect to a network, you must enter an...

2-6Printing Operation 
Set the Security Level to High.
NetWare
This section explains the procedure for enabling NetWare.
1Enter the administrator ID and password. Then, if NetWare is set to 
Off, use U or V to select On and press [OK].
2Press Z.
3Press [OK]. A blinking question mark (?) appears. Each time you 
press U or V, the selection changes.
4Display the item you want to set and press [OK].
5Press [MENU]. The display returns to Ready.
>Security Level
  High
>NetWare       >
  On
>>Frame Type
  Auto...