Kyocera FS 1320D User Manual

							Option6-1
6Option
This chapter explains the options for this printer.
General Information 6-2
Expansion Memory Modules 6-3
Removing a Memory Module 6-5
Verifying the expanded memory 6-5
Paper Feeder (PF-100) 6-6
Network Interface Card (IB-23) 6-7
CompactFlash (CF) Card 6-8
Downloaded From ManualsPrinter.com Manuals 
						

							6-2Option
General Information
The printers have the following options available to satisfy your printing 
requirements. 
For instructions on installing individual options, refer to the 
documentation included with the option. Some options are explained in 
the following sections.
NoteInstall the memory module before installing the optional 
paper feeder (PF-100).
Expansion Memory 
Module (DIMM 
64/128/256/512 MB)
Paper Feeder (PF-100) CF Card
Network Interface 
Card (IB-23)
Downloaded From ManualsPrinter.com Manuals 
						

							Option6-3
Expansion Memory Modules
To expand the printer memory for more complex print jobs and faster 
print speed, you can plug in optional memory module (dual in line 
memory module) in the memory slot provided on the printer main 
controller board. You can select additional memory module from 64, 128, 
256 or 512MB. The maximum memory size is 544MB.
Precautions for handling the printers main controller 
board and memory module
To protect electronic parts, discharge static electricity from your body by 
touching a water pipe (faucet) or other large metal object before handling 
the memory module. Or, wear an antistatic wrist strap, if possible, when 
you install the memory module.
Always hold the main controller board or a memory module by its edges 
as shown below to avoid damaging electronic parts.
Note The expansion memory should only be installed by your 
service technician. We shall not be liable for any damages caused 
by improper installation of expansion memory.
Correct Incorrect
Downloaded From ManualsPrinter.com Manuals 
						

							6-4Option
Installing the Memory Module
1
Turn off the printer and disconnect the power cord and printer cable.
2Remove the right cover as shown in the figure.
3Remove the fixing tape in case of the first installation. Then, remove 
the memory slot cover as shown in the figure.
4Push out the clamps on both ends of the memory socket.
5Remove the memory module from its package.
6Aligning the cutouts of the memory module with the matching keys of 
the socket, carefully plug the memory module into the memory 
socket until it clicks in place.
Downloaded From ManualsPrinter.com Manuals 
						

							Option6-5
7The memory module is secured to the memory socket with the 
clamps.
8Reinstall the memory slot cover and the right cover.
Removing a Memory Module
To remove a memory module, remove the right cover and the memory 
slot cover from the printer. Then, carefully push out the two socket 
clamps. Ease the memory module out of the socket to remove.
Verifying the expanded memory
To verify that the memory module is working properly, test it by printing a 
status page.
Downloaded From ManualsPrinter.com Manuals 
						

							6-6Option
Paper Feeder (PF-100)
The PF-100 allows you to add one (for FS-1120D) or two (for FS-1320D) 
more paper cassette to the bottom of the printer for continuous feeding 
of a large volume of paper. Each paper cassette can hold up to 
approximately 250 sheets of ISO A4, ISO A5, JIS B5, Letter, or Legal 
size (80g/m
2) paper. This feeder is attached at the bottom of the printer 
as shown on the left.
Downloaded From ManualsPrinter.com Manuals 
						

							Option6-7
Network Interface Card (IB-23)
The network interface card supports TCP/IP, IPX/SPX, NetBEUI and 
AppleTalk protocols, so that the printer can be used on network 
environments including Windows, Macintosh, UNIX, NetWare, etc. 
The network interface card must be installed in the option interface slot 
that is located at the back of the printer.
1Turn off the printer and disconnect the power cord and printer cable.
2Open the rear cover.
3Remove the optional interface slot cover.
4Insert the Network Interface Card and secure it with the screws 
removed in step 3.
5Close the rear cover, and connect the printer cable.
6Connect the power cord, and turn on the printer.
7Configure the network address from Quick Setup. For more 
information, refer to Operation Guide of the network card.
CAUTION  Before inserting a network interface card in the 
printer, make sure that the printer is switched off.
Downloaded From ManualsPrinter.com Manuals 
						

							6-8Option
CompactFlash (CF) Card
To read the optional fonts, macros, and overlays stored in the CF card, 
insert the CF card to the slot of the printer according to the following\
 
steps.
The maximum size of the CF card is 256MB. For details of the CF card, 
contact your service technician.
1Turn off the printer and disconnect the power cord and printer cable.
2Open the rear cover.
3Remove the optional interface slot cover.
When the Network Interface Card is installed, remove it.
CAUTION  Before inserting a CF card  in the printer, make 
sure that the printer is switched off.
Downloaded From ManualsPrinter.com Manuals 
						

							Option6-9
4Insert the CF Card.
5Secure it with the screws removed in step 3.
6Connect the power cord and printer cable and turn on the printer. 
Downloaded From ManualsPrinter.com Manuals 
						

							6-10Option
Downloaded From ManualsPrinter.com Manuals