Kyocera FS 1120DN User Manual

							ix
Safety Infor mation
Laser Safety
This printer is certified as a Class 1 laser product under the U.S. 
Department of Health and Human Services (DHHS) Radiation 
Performance Standard according to Radiation Control for Health and 
Safety Act of 1968. This means that the printer does not produce 
hazardous laser radiation. Since radiation emitted inside the printer is 
completely confined within protective housings and external covers, the 
laser beam cannot escape from the printer during any phase of user 
operation.
Laser Notice
This printer is certified in the U.S. to conform to the requirements of 
DHHS 21 CFR Subchapter for Class I (1) laser products, and elsewhere 
is certified as a Class I laser product conforming to the requirements of 
IEC 825.
Radio Frequency Transmitter
This machine contains a transmitter module. We, the manufacturer 
(Kyocera Mita Corporation) hereby declare that this equipment (page 
printer), model FS-1120D and FS-1320D are in compliance with the 
essential requirements and other relevant provisions of Directive 
1999/5/EC.
Radio Tag Technology
In some countries, the radio tag technology used in this equipment to 
identify the toner container may be subject to authorization, and the use 
of this equipment may consequently be restricted.
DANGER  CLASS 3B INVISIBLE LASER RADIATION 
WHEN OPEN. AVOID DIRECT EXPOSURE TO BEAM.
CAUTION   Use of controls or adjustments or performance 
of procedures other than those specified herein may result 
in hazardous radiation exposure.
Downloaded From ManualsPrinter.com Manuals 
						

							x
Caution Labels
The printer bears any of the following labels.
CDRH Regulations
The Center for Devices and Radiological Health (CDRH) of the U.S. 
Food and Drug Administration implemented regulations for laser 
products on August 2, 1976. These regulations apply to laser products 
manufactured after August 1, 1976. Compliance is mandatory for 
products marketed in the United States. A label indicating compliance 
with the CDRH regulations must be attached to laser products marketed 
in the United States.
Ozone Concentration
These printers generate ozone gas (O3), which may concentrate in the 
place of installation and cause an unpleasant smell. To minimize the 
concentration of ozone gas to less than 0.1ppm, we recommend you not 
to install the printer in a confined area where ventilation is blocked.
Laser inside the printer
(Laser radiation warning) Laser inside the printer
(Laser radiation warning)For Europe, Asia, and 
other countries For U.S.A. and 
Canada
Downloaded From ManualsPrinter.com Manuals 
						

							xi
DECLARATION OF CONFORMITY TO
2004/108/EC, 2006/95/EEC, 93/68/EEC, 1999/5/EC and 2009/125/EC
We declare under our sole responsibility that the product to which this 
declaration relates is in conformity with the following specifications. EN55024
EN55022 Class B
EN61000-3-2
EN61000-3-3
EN60950-1
EN60825-1
EN300 330-1
EN300 330-2
EN62301
Canadian Department of Communications 
Compliance Statement
This Class B digital apparatus complies with Canadian ICES-003.
Avis de conformité au x normes du ministere 
des Communications du Canada
Cet appareil numérique de la classe B est conforme à la norme NMB-
003 du Canada.
EN ISO 7779
Maschinenlärminformations-Verordnung 3. GPSGV, 06.01.2004: Der 
höchste Schalldruckpegel beträgt 70 dB (A) oder weniger gemäß EN 
ISO 7779.
EK1-ITB 2000
Das Gerät ist nicht für die Benutzung im unmittelbaren Gesichtsfeld am 
Bildschirmarbeitsplatz vorgesehen. Um störende Reflexionen am 
Bildschirmarbeitsplatz zu vermeiden, darf dieses Produkt nicht im 
unmittelbaren Gesichtsfeld platziert werden.
Disclaimer
Kyocera Mita will not be liable to customers or any other person or entity 
for any loss or damage caused or alleged to be caused directly or 
indirectly by equipment sold or furnished by us, including but not limited 
to, any interruption of service, loss of business or anticipatory profits, or 
consequential damages resulting from the use or operation of the 
equipment or software.
Downloaded From ManualsPrinter.com Manuals 
						

							xii
Safety Instructions Regarding the 
Disconnection of Power
Caution:  The power plug is the main isolation device! Other switches on 
the equipment are only functional switches and are not suitable for 
isolating the equipment from the power source.
VORSICHT:  Der Netzstecker ist die Hauptisoliervorrichtung! Die 
anderen Schalter auf dem Gerät sind nur Funktionsschalter und könn\
en 
nicht verwendet werden, um den Stromfluß im Gerät zu unterbrechen.
Energy Saving Function
This printer comes equipped with a Sleep Mode where printer function 
remains in a waiting state but power consumption is still reduced to a 
minimum when there is no activity with the printer within a set amount of 
time.
Sleep Mode
This printer automatically enters Sleep Mode when approximately 15 
minutes have passed since the printer was last used. The amount of 
time of no activity that must pass before Sleep Mode is activated may be 
lengthened.
Duplex Printing
This printer includes duplex printing as a standard function. For example, 
by printing two single-sided originals onto a single sheet of paper as a 
duplex printing, it is possible to lower the amount of paper used. 
Recycled Paper
This printer supports recycled paper which reduces the load on the 
environment. Your sales or service representative can provide 
information about recommended paper types.
Energy Star (ENERGY STA R®) Program 
We have determined as a participating company in the International 
Energy Star Program that this product is compliant with the standards 
laid out in the International Energy Star Program.
Downloaded From ManualsPrinter.com Manuals 
						

							xiii
Symbols
The sections of this guide and parts of the machine marked with symbols 
are safety warnings meant to protect the user, other individuals and 
surrounding objects, and ensure correct and safe usage of the machine. 
The symbols and their meanings are indicated below.
The following symbols indicate that the related section includes safety 
warnings. Specific points of attention are indicated inside the symbol.
The following symbols indicate that the related section includes 
information on prohibited actions. Specifics of the prohibited action are 
indicated inside the symbol. 
The following symbols indicate that the related section includes 
information on actions which must be performed. Specifics of the 
required action are indicated inside the symbol.
Please contact your service representative to order a replacement if the 
safety warnings in this Operation Guide are illegible or if the guide itself 
is missing. (fee required) DANGER
: Indicates that serious injury or even death will very 
possibly result from insufficient attention to or incorrect 
compliance with the related points.
WARNING : Indicates that serious injury or even death may 
result from insufficient attention to or incorrect compliance with 
the related points.
CAUTION : Indicates that personal injury or mechanical 
damage may result from insufficient attention to or incorrect 
compliance with the related points.
.... [General warning]
.... [Warning of danger of electrical shock]
.... [Warning of high temperature]
.... [Warning of prohibited action]
.... [Disassembly prohibited]
.... [Alert of required action]
.... [Remove the power plug from the outlet]
.... [Always connect the machine to an outlet with a ground 
connection]
Downloaded From ManualsPrinter.com Manuals 
						

							xiv
Installation Precautions
Environment
Caution
Avoid placing the machine on or in locations which are unstable 
or not level. Such locations may cause the machine to fall down 
or fall over. This type of situation presents a danger of personal 
injury or damage to the machine.
Avoid locations with humidity or dust and dirt. If dust or dirt 
become attached to the power plug, clean the plug to avoid the 
danger of fire or electrical shock.
Avoid locations near radiators, heaters, or other heat sources, or 
locations near flammable items, to avoid the danger of fire.
To keep the machine cool and facilitate changing of parts and 
maintenance, allow access space as shown below. Leave 
adequate space, especially around the rear cover, to allow air to 
be properly ventilated out of the printer.
Other Precautions
Adverse environmental conditions may affect the safe operation and 
performance of the machine. Install in an air-conditioned room 
(recommended room temperature: around 23°C (73.4°F), humidity: 
around 60% RH), and avoid the following locations when selecting a site 
for the machine.
•Avoid locations near a window or with exposure to direct sunlight.
• Avoid locations with vibrations. 
• Avoid locations with drastic temperature fluctuations. 
• Avoid locations with direct exposure to hot or cold air.
• Avoid poorly ventilated locations.
During printing, some ozone is released, but the amount does not cause 
any ill effect to ones health. If, however, the printer is used over a long 
period of time in a poorly ventilated room or when printing an extremely 
large number of copies, the smell may become unpleasant. To maintain 
the appropriate environment for print work, it is suggested that the room 
be properly ventilated.
11-13/16
(300mm) 7-7/8
(200mm)
11-13/16
(300mm) 19-11/16
(500mm)
7-7/8
(200mm)
Downloaded From ManualsPrinter.com Manuals 
						

							xv
Power Supply/Grounding the Machine
Warning
Do not use a power supply with a voltage other than that 
specified. Avoid multiple connections in the same outlet. These 
types of situations present a danger of fire or electrical shock.
Plug the power cord securely into the outlet. If metallic objects 
come in contact with the prongs on the plug, it may cause a fire or 
electric shock.
Always connect the machine to an outlet with a ground 
connection to avoid the danger of fire or electrical shock in case 
of an electric short. If an earth connection is not possible, contact 
your service representative.
Other precautions
Connect the power plug to the closest outlet possible to the machine.
The power supply cord is used as the main disconnect device. Ensure 
that the socket/outlet is located/installed near the equipment and is 
easily accessible.
Handling of plastic bags
Warning
Keep the plastic bags that are used with the machine away from 
children. The plastic may cling to their nose and mouth causing 
suffocation.
Downloaded From ManualsPrinter.com Manuals 
						

							xvi
Precautions for Use
Cautions when using the machine
Warning
Do not place metallic objects or containers with water (flower 
vases, flower pots, cups, etc.) on or near the machine. This 
situation presents a danger of fire or electrical shock should they 
fall inside. 
Do not remove any of the covers from the machine as there is a 
danger of electrical shock from high voltage parts inside the 
machine.
Do not damage, break or attempt to repair the power cord. Do not 
place heavy objects on the cord, pull it, bend it unnecessarily or 
cause any other type of damage. These types of situations 
present a danger of fire or electrical shock.
Never attempt to repair or disassemble the machine or its parts as 
there is a danger of fire, electrical shock or damage to the laser. If 
the laser beam escapes, there is a danger of it causing blindness.
If the machine becomes excessively hot, smoke appears from the 
machine, there is an odd smell, or any other abnormal situation 
occurs, there is a danger of fire or electrical shock. Turn the main 
power switch off ({) immediately, be absolutely certain to remove the 
power plug from the outlet and then contact your service representative.
If anything harmful (paper clips, water, other fluids, etc.) falls into 
the machine, turn the main power switch off ( {) immediately. 
Next, be absolutely certain to remove the power plug from the 
outlet to avoid the danger of fire or electrical shock. Then contact your 
service representative.
Do not remove or connect the power plug with wet hands, as 
there is a danger of electrical shock.
Always contact your service representative for maintenance or 
repair of internal parts.
Caution
Do not pull the power cord when removing it from the outlet. If the 
power cord is pulled, the wires may become broken and there is a 
danger of fire or electrical shock. (Always grasp the power plug 
when removing the power cord from the outlet.)
Always remove the power plug from the outlet when moving the 
machine. If the power cord is damaged, there is a danger of fire or 
electrical shock.
If the machine will not be used for a short period of time 
(overnight, etc.), turn the power switch off (O). If it will not be used 
for an extended period of time (vacations, etc.), remove the power 
plug from the outlet for safety purposes during the time the machine is 
not in use..
Always hold the designated parts only when lifting or moving the 
machine.
For safety purposes, always remove the power plug from the 
outlet when performing cleaning operations.
Downloaded From ManualsPrinter.com Manuals 
						

							xvii
If dust accumulates within the machine, there is a danger of fire or 
other trouble. It is therefore recommended that you consult with 
your service representative in regard to cleaning of internal parts. 
This is particularly effective if accomplished prior to seasons of 
high humidity. Consult with your service representative in regard 
to the cost of cleaning the internal parts of the machine.
Other precautions
Do not place heavy objects on the machine or cause other damage to 
the machine.
Do not open the upper front cover, turn off the main power switch, or pull 
out the power plug during printing.
When lifting or moving the machine, contact your service representative.
Do not touch electrical parts, such as connectors or printed circuit 
boards. They could be damaged by static electricity.
Do not attempt to perform any operations not explained in this 
handbook.
Use shielded interface cables.
Caution
Use of controls or adjustments or performance of procedures other than 
those specified herein may result in hazardous radiation exposure.
Cautions when Handling Consumables 
Caution
Do not attempt to incinerate the Toner Container. Dangerous 
sparks may cause burns.
Keep the Toner Container out of the reach of children.
If toner happens to spill from the Toner Container, avoid inhalation 
and ingestion, as well as contact with your eyes and skin.
• If you do happen to inhale toner, move to a place with fresh 
air and gargle thoroughly with a large amount of water. If coughing 
develops, contact a physician.
• If you do happen to ingest toner, rinse your mouth out with water and 
drink 1 or 2 cups of water to dilute the contents of your stomach. If 
necessary, contact a physician.
• If you do happen to get toner in your eyes, flush them thoroughly 
with water. If there is any remaining tenderness, contact a physician.
• If toner does happen to get on your skin, wash with soap and water.
Do not attempt to force open or destroy the Toner Container.
Other precautions
After use, always dispose of the Toner Container in accordance with 
Federal, State and Local rules and regulations.
Store all consumables in a cool, dark location.
If the machine will not be used for an extended period of time, remove 
the paper from the cassette, return it to its original package and reseal it.
Downloaded From ManualsPrinter.com Manuals 
						

							xviii
About the Operation Guide
This Operation Guide contains the following chapters:
1Machine Parts
This chapter explains the names of parts.
2 Loading Paper
This chapter explains paper specifications for this printer and how to 
load paper into the cassette or MP tray.
3Printing
This chapter explains how to install the printer driver, print from your PC, 
and use the application software included in the CD-ROM. 
4 Maintenance
This chapter explains how to replace the toner container and how to care 
for your printer.
5 Troubleshooting
This chapter explains how to handle printer problems that may occur, 
such as paper jams.
6 Options
This chapter explains the options for this printer.
7 Specifications
This chapter lists the specifications of this printer.
Downloaded From ManualsPrinter.com Manuals