Knoll Systems Ht221 Projector User Manual
Have a look at the manual Knoll Systems Ht221 Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 14 Knoll Systems manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![](/img/blank.gif)
Storing the most recent “PICTURE ADJ,” “FINE PICTURE,” “H\ POSITION,” AND “V POSITION” settings You can store the above present settings in the memory. CUSTOM 1 to 5. 1. Select the input source RGB (see page 13). 2. Press MENU to display the main menu. 3. Press the cursor up or down key to select “SETTING MENU.” 4. Press L-CLICK to display the SETTING MENU. 5. Press the cursor up or down key to select “CUSTOM MEMORY.” 6. Press the cursor +/- key to select the memory CUSTOM 1 to 5. 7. Press L-CLICK to store the settings. The menu will be turned off after storing the settings. Retrieving data from the custom memory/Setting “RGB” to “STANDARD” The stored settings in the CUSTOM 1 to 5 memories can be retrieved as follows: 1. Select “RGB” as the input source (see page 13). 2. Press the cursor +/- key to select the memory CUSTOM 1 to 5 or “STANDARD.” If you select “STANDARD,” the unit will select the most suitable resolution automatically. 3. Press L-CLICK to retrieve the settings. If the image (and the menu) has disappeared because the wrong custom memory is selected Carry out the following steps. 1. Turn off the source connected to the RGB IN connector. The incoming signals from the source go down and blue, black, or focus pattern screen will be displayed (the background type differs depending on the “BACKGROUND” setting. See page 19.). 2. Select the right custom memory by restarting Retrieving data from the custom memory above. Selecting the starting mode for the next projector use Set “STARTING RGB” to “LATEST” to use the most recent settings (RGB STANDARD or CUSTOM 1 to 5) when you turn on the unit next. If you set “STARTING RGB” to “STANDARD,” the unit will select the most suitable resolution every time you turn on the unit. 1. Carry out steps 1 to 4 in “Storing the most recent settings” on the previous page. 2. Press the cursor up or down key to select “STARTING RGB.” 3. Press the cursor +/- key to select either “LATEST” or “STANDARD.” 4. Press L-CLICK. The change of settings will be confirmed. Resetting the present settings to factory settings To reset the changed “PICTURE ADJ,” “FINE PICTURE,” “H PO\ SITION,” and “V POSITION” to the factory settings, carry out the following steps. 1. Carry out steps 1 to 4 in “Storing the most recent settings” on the previous page. 2. Press the cursor up or down key to select “RESET.” The horizontal frequency of the present incoming signal appears under the title “RESET.” 3. Press and hold down the cursor + key for more than three seconds until “COMPLETE” appears instead of the horizontal frequency. Resetting the present settings and all the custom memories to factory settings Note: If you carry out this procedure, not only the custom memories but also all the menu items except for “LAMP USAGE,” and “LANGUAGE” will be reset. 1. Carry out steps 1 to 4 in “Storing the most recent settings” on the previous page. 2. Press the cursor up or down key to select “ALL RESET.” 3. Press and hold down the cursor + key for more than three seconds until “COMPLETE” appears under the title “ALL RESET.” 21
![](/img/blank.gif)
Adjusting the picture elements The picture elements such as brightness, contrast, white balance, and so on can be adjusted individually for each input source. The adjustable items vary depending on the input source and “INPUT MODE” setting. (The elements marked with “O” are adjustable.) VIDEO S-VIDEO RGB BRIGHTNESS O O CONTRAST O O COLOR O -- TINT O -- SHARPNESS O -- WHITE BALANCE O O 1. Select the input source. 2. Press MENU to display the main menu. 3. Press the cursor up or down key to select “IMAGE ADJ MENU.” 4. Press L-CLICK to display the IMAGE ADJ MENU. 5. Press the cursor up or down key to select “BRIGHTNESS,” then press the cursor +/- key to adjust the brightness. 6. Press the cursor up or down key to select “CONTRAST,” then press the cursor +/- key to adjust the contrast. 7. Press the cursor up or down key to select “COLOR,” then press the cursor +/- key to adjust the color. If the input source is RGB and “INPUT MODE” is “RGB,” skip t\ his step and go to step 10. 8. Press the cursor up or down key to select “TINT,” then press the cursor +/- key to adjust the tint. Note: The tint control doesn’t operate with a PAL or SECAM source. 9. Press the cursor up or down key to select “SHARPNESS,” then press the cursor +/- key to adjust the sharpness. If the input source is RGB, skip this step and go to the next step. 10.Press the cursor up or down key to select “WHITE BALANCE,” then press L-CLICK. The WHITE BALANCE menu appears. 11.Press the cursor up or down key to select each item in the WHITE BALANCE menu, and then press the cursor +/- key to adjust the item for the white color balance. Selecting the picture type The picture types can be selected individually for each input source according to the video content and your preferences. 1. Select the input source. 2. Press MENU to display the main menu. 3. Press the cursor up or down key to select “IMAGE ADJ MENU.” 4. Press L-CLICK to display the IMAGE ADJ MENU. 5. Press the cursor up or down key to select “IMAGE MODE.” 6. Press L-CLICK to display the IMAGE MODE menu. 7. Press the cursor up or down key to select “GAMMA,” then press the cursor +/- key to select the gamma mode. 22
![](/img/blank.gif)
The following three types of gamma modes can be selected according to your preferences: • NORMAL, • NATURAL 1, or • NATURAL 2. 8. Press L-CLICK. 9. Press the cursor up or down key to select “INPUT MODE,” then press the cursor +/- key to select the input mode. If the input source is VIDEO or S-VIDEO, the following two types can be selected: • GRAPHICS for displaying a graphic image, or • TEXT for displaying a text image such as the image from the document camera. 10. Press L-CLICK 11. Press the cursor up or down key to select “WHITE PICTURE,” then press the cursor +/- key to select the white picture mode. The following two types can be selected: • NORMAL, or • QUIET to reduce brightness for better color expression, 12. Press L-CLICK . Activating the power saving function This function operates only with an RGB input source. If the input signals from the RGB IN connector go down for more than five minutes, the projector will automatically turn off and enter the standby mode. 1. Press MENU to display the main menu. 2. Press the cursor up or down key to select “POWER MENU.” 3. Press L-CLICK to display the POWER MENU. 4. Press the cursor up or down key to select “POWER OFF,” then press the cursor + key to select “ON” to activate the power saving function. To deactivate the function, set “POWER OFF” to “OFF” by pressing the cursor – key. Activating the on-screen function If you activate the on-screen function, • The input source “VIDEO,” “S-VIDEO,” or “RGB” will be displayed for three seconds when you have selected the input source with the remote control, and • The message “POWER OFF/ENTER” will be displayed on the screen when you press the projector POWER button. If “DISPLAY” is set to “ON” this pre\ vents the projector from being turned off accidentally. 1. Press MENU to display the main menu. 2. Press the cursor up or down key to select “SETTING MENU.” 3. Press L-CLICK to display the SETTING MENU. 4. Press the cursor up or down key to select “DISPLAY,” then press the cursor + key to select “ON” to activate the on-screen function. To deactivate the function, set “DISPLAY” to “OFF” by pressing the cursor – key. Turning the projector off with on screen functions With the remote control: Press the POWER OFF button a for 2 seconds (the projector will turn off regardless of the “POWER OFF” settin\ g) With the projector keypad: Press the POWER button for 2 seconds. The projector will turn off. 23
![](/img/blank.gif)
Checking hours of lamp use The lamp housing must be replaced after 1000 hours of use. When 1000 hours have elapsed the\ STATUS indicator will light in red. Periodically check hours of lamp use in the menu so that you will have time to purchase a new lamp housing before the old one is burnt out. 1. Press MENU to display the main menu. 2. Press the cursor up or down key to select “POWER MENU.” 3. Press L-CLICK to display the POWER MENU. 4. Press the cursor up or down key to select “LAMP USAGE.” to display the lamp hours. Resetting the lamp use hours to zero You need to reset the lamp use hours to zero after replacing the lamp housing. 1. Carry out the steps above. 2. Press the POWER ON button on the remote control for more than ten seconds. “LAMP USAGE” will be set to zero. If the projector doesn’t turn on because lamp use exceeds 1100 hours. The projector is designed not to turn on after the lamp use has exceeded 1100 hours. (If the unit is in use, it will go off). If this happens you must replace the lamp housing with a new one immediately. After replacing the lamp housing, you need to reset the lamp use hours to zero to enable you to turn on the unit. You should never reset the projector lamp usage with a lamp that has exceeded 1100 hours. There is a real possibility that the lamp could blow up destroying the projector innards and causing injury or death. 1. Switch on the main power. 2. Press the POWER OFF button on the remote control for more ten seconds. “LAMP USAGE” will be reset to zero and the STATUS indicator will go o\ ff. Resetting all to the factory settings All the menu items and CUSTOM 1 to 5 memories can be reset to the factory settings except for the followings: • LANGUAGE • LAMP USAGE 1. Press MENU to display the main menu. 2. Press the cursor up or down key to select “SETTING MENU.” 3. Press L-CLICK to display the SETTING MENU. 4. Press the cursor up or down key to select “ALL RESET.” 5. Press the cursor + key for more than three seconds. “COMPLETE” appears under the title “ALL RESET” after the reset has completed. . . . . . . . . . . . 24
![](/img/blank.gif)
Specifications Optical DMD TM Single Chip Digital Micro Device (DMD), 1024x768 dots Lens Manual zoom, manual focus F3.0 f =35 to 42mm Lamp High Performance compact lamp 150W Image Size 635 to 7620mm (25 to 300 inches) diagonal Projection Distance 1.2 to 12.3m Light Output 1300 ANSI lumens (normally white) Contrast Ratio 800:1 Color Temperature 7000 Kelvin Electrical Inputs Video (NTSC / PAL / SECAM / NTSC4.43) RGB (H:15 to 85 kHz, V:50 to 85 Hz) Video Bandwidth 60 MHz Color Reproduction Full color, 16.7 million colors simultaneously. Horizontal Resolution NTSC 500, PAL 500, SECAM 300, NTSC4.43 350 TV lines RGB 1024 dots horizontal, 768 dots vertical Power Requirement 100 to 120/220 to 240 VAC, 50/60 Hz Input Current 2.2A/1.0 A (400W) Mechanical Dimensions 23.5cm (W) x 5.8cm (H) x 29.7cm (D) 9.3 x 2.3 x 11.7 Net Weight 2.6 kg/5.7 lbs Operational Temperatures Data projector: 5 degree to 35 degree Celsius (41 degree to 95 degree Fahrenheit), 30 to 85% humidity Remote control: 0 degree to 60 degree Celsius (32 degree to 140 degree Fahrenheit) Regulations UL Approved (UL 1950, CSA 950) Meets DOC Canada requirements Meets FCC Class A requirements Meets EMC Directive (EN55022, EN61000-3-2, EN61000-3- 3, EN50082-1) Meets Low Voltage Directive (EN60950, TUV GS Approved) CE Approved for EU D-Sub Pin Assignments 1 Red 6 Red Gnd 11 GND 2 Green 7 Green Gnd 12 SDA 3 Blue 8 Blue Gnd 13 Horizontal Sync 4 GND 9 N/C 14 Vertical Sync 5 GND 10 Digital Gnd 15 SCL 25
![](/img/blank.gif)
. . Troubleshooting This section helps you resolve problems while setting up or using your projector. Common Problems & Solutions Problem Check These Items Does not turn on Check that the cord is plugged in. Test the outlet. Check the status light to see if the projector has overheated or the lamp usage exceeds 1100 hours. No picture Use the menu icons to select your source (Video, S- Video, or RGB). Ensure your source cables are connected properly. Adjust the brightness and contrast Remove the lens cap. Is the STATUS indicator blinking? Image isn’t square to the screen Reposition the projector to improve its angle to the screen Use remote control keystone button to correct offset. Picture is blurred Adjust the focus Reposition the projector to improve its angle to the screen. Ensure that the distance between the projector and screen is within the minimum and maximum adjustment range of the lens Remote control does not work Install new batteries. Low batteries may activate the laser but be insufficient to generate IR commands. Make sure there are no obstacles between you and the projector. Stand within 13 feet (4m) of the projector. The STATUS indicator is lit or blinking See the Status Light message chart on the next page. Cross color in RGB mode If “Auto Picture” is off, turn it on. If “Auto Picture” is on, turn it off and balance the image with the Picture Adjustment icon and Fine Picture Adjustment icon 26
![](/img/blank.gif)
When the STATUS indicator on the projector keypad lights or blinks Status Light Message Condition Status OFF Normal On Continually The projector lamp has exceeded 1000 hours of operation and should be replaced. Blinking Very Rapidly (On and off in a cycle of 1 sec.) The lamp housing is not correctly installed. Install it correctly. Blinking Rapidly (On and off in a cycle of 4 sec.) The temperature protector has been triggered. If the room temperature is high, move the projector to a cool location. If the temperature within the projector is high, check the cooling fan ventilation hole and the ventilation hole on the bottom of the projector. If any holes are blocked, remove whatever is blocking them. The temperature protector has been triggered. If you switch the main Power switch Off, then immediately switch it On again; sometimes the power does not come on. If this happens, wait one minute, and then switch the power On again. The lamp lighting voltage error detection protector has been triggered. Wait at least one minute before switching it on again. If this does not solve the problem, please contact your dealer. Blinking Slowly (On and off in a cycle of 8 sec.) The cooling fan has stopped. Contact your Knoll dealer for service. Blinking Very Slowly (On and off in a cycle of 12 sec.) The lamp is not turned on. The projector was turned off and back on too quickly. Turn off the projector, wait one minute, then turn the projector back on. Or the lamp is burnt out. Replacing the lamp housing After the lamp has been operating for 1000 hours or longer, the STATUS indicator on the control panel will light and “LAMP USAGE” icon, which shows hours of total lamp use, will be displayed on the screen. When this happen, turn off the unit and replace the lamp housing with new one. The unit will not be go on after 1100 hours. (It will go off\ if it is in use.) ***CAUTION*** • DO NOT TOUCH THE LAMP immediately after it has been used. It will be extremely hot. Allow at least one hour for the lamp to cool before handling. • DO NOT LOOSEN ANY SCREWS except for those mentioned in the instructions \ below. There is danger of electric shock. 27
![](/img/blank.gif)
Lamp housing replacement procedure 1. Wait at least one hour for the lamp to cool 2. Unplug the power cord. 3. Turn the unit upside down carefully. 4. Loosen the lamp cover securing screw and remove the lamp cover. CAUTION: Do not use a lamp housing other than the Knoll replacement lamp housing. Order this from your Knoll dealer using your projector’s model number (see “Note” below). 5. Loosen the three lamp housing securing screws. (This projector has a safety switch.) 6. Hold the handle then pull the lamp housing upward to remove it. 7. Install the new lamp housing. 8. Secure the lamp housing with the three screws. 9. Replace and secure the lamp cover with the securing screw. 10. Return the unit to the normal position, connect the power cord, and turn on the unit. 11. Reset the lamp time. Select the lamp usage time menu, then press the POWER ON button on the remote control and hold it down for at least ten seconds. Note: When the lamp usage time reaches 1100 hours, it becomes impossible to switch on the power and menus are not displayed. In this case, press the remote control POWER OFF button for at least 10 seconds in the standby mode. It is possible to confirm whether it has been reset or not by checking whether the STATUS indicator is extinguished. Obtain a replacement lamp from your dealer where the projector was purchased. When ordering a replacement lamp, specify the correct special replacement lamp – model name U2-150 (Product code 28-640). Knoll Systems 145 Tyee Drive Point Roberts, WA USA 98281 11791 Machrina Way, Richmond BC Canada V7A 4V3 © Copyright 1999-2001 All Rights Reserved 28